AirLive AirMax5X II 5G Outdoor CPE Installation Guide

AirLive AirMax5X II 5G Outdoor CPE

Device Installation

(AirMax5X II Outdoor CPE taken as an example)

Wireless Connection Topology

Point to Point

Bridge Ways

(“Two way bridge setup: One Push Bridge or LED Display Bridge, choose the one best for your setup.)

1. Config Masterl Slave CPE
   Put the switch to H, CPE will work as Master. Put the switch to C, CPE will work as Slave. Note : The pictures of the above products may change slightly according to the production cycle, and the final appearance is based on the physical object.

2. Point to Point Connection
   Press reset button on both master and slave CPE, will start bridging.
   Point to mult Point Connection
   Press reset button on master and mult slave CPEs, will start bridging.
   Note : Master CPE and slave CPE bridging actions (press reset button) need to be finished in 1 minute.

LED Display Bridge

1. Config Master CPE
   When bridge two CPES, make one work as master: press F to make H/ C blinking, and press S’ to change to “H, it will save automatically in 5 seconds.

2. Config Slave CPE
   Set another CPE to work as slave : press “F to make H/ C blinking, and press “S to change to “C’, it will save automatically in 5 seconds. Note:

3. CPE default working mode is AP mode after reset, IP is 192.168.1.253

4. is select button, can be used to choose master/ slave working mode, wifi channel, IP, and checking signal strength

5. is config button, can be used to set master/ slave working mode, wifi channel, IP

6. Point to Point Connection
   Press reset button on both master and slave CPE, will start bridging. Point to mult Point Connection as casat bıutan an maatar and mut alauaDrA will atat bridaina.

7. Change Wifi channel
   To avoid signal interference, need to change master CPE wifi channel only, slave CPE wil reboot and bridge to master CPE automatically. Press F twice, change channel by press S, CPE will save and reboot automatically in 5 seconds,

8. Change lP
   To avoid CPE IP conflicts, need to change CPE IP address. Press F three times until the IP is blinking, press S to change IP, CPE will save and reboot automatically in 5 seconds.

Web Configuration

PC configuration if PC connect CPE by wireless
Set PC wireless network IP to 192.168.1. x (x: 2.-250), same network segment as CPE, subnet mask: 255.255.255.0:

After IP address configuration, connect to CPE’s wireless SSID : Wireless 5.8G, and input password (Default Password: 123456789)

Login Web Configuration
Use a browser to access http://192.168.1.253, pop up the login page shown below,input the login password: admin, enter into the home page.

Repeat mode
Bridge the exist wireless signal then transmit Wi-Fi for more range

AP mode
In this mode, NAT, DHCR firewall, and all WAN-related functions are turned off. All wireless and wired interfaces are bridged together, regardless of LAN and WAN

Bridge Status

Login CPE (work as repeater), will see signal strength, green is normal, between -70dBm to 40dBm.

www.airive.com

Declaration of Conformity
We, Manufacturer/lmporter AirLive Technology Corporation 4F, No.132, Lane 235, Baoqian Rd., Xindian Dist., New Taipei City 23145, Taiwan Declare that the product Wi-Fi 5Ghz N300 Outdoor CPPE AirMax5X II is in conformity with In accordance with 2014/30/EU and 2014/35/EU Directive

Clause

• EN 55032:2015
• EN 62368-1
• CE marking

Description

• Electromagnetic compatibility (EMC)
• Electromagnetic compatibility (LVD)

Regulatory Approvals

CE Statement
This product complies with the 2014/30/EU and 2014/35/EU directives, including the following safety and EMC standards:

• EN 55032:2015
  Electromagnetic compatibility (EMC)

• ETSI EN 301 489-1 V2.2.3 (2019-11)
  Electromagnetic compatibility (EMC)

• ETSI EN 301 489-17 V3.2.4 (2020-09)
  Electromagnetic compatiblity (EMc)

• EN 55035:2017
  Electromagnetic compatibility (EMC)

• EN 62368-1:2014+A11:2017
  Electromagnetic compatibility (LVD) – Safety

• ETSI EN 302 502 V2.1.3 (2017-07)

• EN IEC 62311:2020

• EN 50665:2017

CE Marking Warning
This is a Class A product. In a domestic enviroment this product may cause radio interference in which case the user may be required to take adequate measures.

TroubleShooting

AirLive Technology Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of directive 2014/30/EU.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>