Uolfin A03773 Quinn 2-Light 13.6-Inch Black Incandescent Semi-Flush Mount Light Installation Guide

: June 3, 2024
: Uolfin

Table of Contents

IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
PARTS TYPE & QTY INCLUDING
- ACCESSORIES & QTY ENCLOSED
ASSE
MBLY & INSTALLATION INSTRUCTIONS
CLEANING
ORDERING PARTS
Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Uolfin A03773 Quinn 2-Light 13.6-Inch Black Incandescent Semi-Flush Mount Light Installation Guide

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture.
Tools Required

PARTS TYPE & QTY INCLUDING

(B) Round mounting plate (1)
(C) Green ground screw (1)
(E) Canopy (1)
(F) Knob nut (2)
(G) Stem (1)
(H) Iron frame (3)
(I) Sockets assembly (1)

ACCESSORIES & QTY ENCLOSED

(A) Plastic wire connector (3)
(D) Mounting screw (2)

ASSE

MBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position.
Unscrew knob nuts (F) from mounting plate (B).
Pass fixture wires through stem (G) and then screw stem (G) onto the top of iron frames (H). Hand tighten till snug.
Attach mounting plate (B) to the outlet box with mounting screws (D).
Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart

Connect wires according to the below chart
***Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord ( round & smooth )| *Parallel cord ( square & ridged )
ClearlBrown,Gold or Black without tracer| ClearlBrown,Gold or Black with tracer
Insulated wire ( other than green ) with copper conductor| Insulated wire ( other than green ) with silver conductor

*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth **( see illus. )

** Twist wires together with plastic wire connector until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (F) onto the pre-assembled threaded nipples on mounting plate (B).

Note: canopy (E) should be snug against the ceiling and knob nuts (F). If not, adjust the length of the pre-assembled threaded nipples on mounting plate assembly (B) by unscrewing the pre-assembled hex nuts and then screwing threaded nipples in or out of mounting plate (B) until the length is achieved. Tighten the hex nuts and back to step 7.
Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap.) Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.