Uolfin 4978119 2-Light 12 Inch LED Semi-flush Mount Light Instruction Manual

Uolfin 4978119 2-Light 12 Inch LED Semi-flush Mount Light

Item Number: 497811 9

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Mounting plate (1)

• (D) Green ground screw (1)

• (E) Hex nut (1)

• (F) Spring washer (1)

• (G) Flat washer (1)

• (H) Canopy (1)

• (I) Knob nut (2)

• (J) Stem (1)

• (K) Iron plate (1)

• (L) Iron frame (1)

• (M) Tube (1)

• (N) Sockets assembly (1)
  ACCESSORIES & QTY ENCLOSED:

• (A) Plastic Wire Connector (3)

• (B) Mounting screw (2)

• (O) Spanner (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above figure.

2. Unscrew knob nuts (I) from canopy (H), then gently remove mounting plate (C) from canopy (H) and set them aside for later installation.

3. Pass the fixture wires through iron frame (L), iron plate (K) and stem (J), then screw stem (J) to the top of tube (M).

4. Unscrew hex nut (E), remove spring washer (F) and flat washer (G) from stem (J).
   Screw canopy (H) onto the top of stem (J) then pass the fixture wires through the previously removed fittings as shown in the illustration and secure with hex nut (E). Tighten with spanner (O) till snug.

5. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

6. Carefully pass supply wires through the center of mounting plate (C).
   Secure mounting plate (C) to the outlet box with mounting screws (B).
   NOTE: the side of mounting plate marked “GND” must face out.

7. Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the below chart Connect wires according to the below chart
   Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

8. Raise canopy (H) to the outlet box. Align the holes in canopy (H) and the preassembled mounting screws on mounting plate (C), then secure canopy (H) with the previously removed knob nuts (I) till snug.
   Note: canopy (E) should be snug against the ceiling with the knob nuts (I). If not,remove canopy (H), adjust the length of the nipples on the mounting plate assembly (C) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled mounting screws in or out of the mounting plate until the secure length is achieved. Tighten the pre-assembled hex nuts and back to step 8.

9. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

10. Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

+1 850 296 2377 Working hours : Mon – Fri 9:00 a.m. – 16:00 p.m. EST uolfin@newdecorworld.com

uolfin@newdecorworld.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>