Uolfin 4978124 Matte Black and Gold Geometric Mini Kitchen Island Light Instruction Manual

Uolfin 4978124 Matte Black and Gold Geometric Mini Kitchen Island Light

Item Number: 4978124
WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3.  Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the
   “OFF” position.
   B) Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6.  Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8.  When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (A) Mounting plate assembly (1)
• (B) Green ground screw (1)
• (E) Canopy (1)
• (F) Strain relief (2)
• (G) Ball knob (2)
• (H) Cord (1)
• (I) Socket (1)
• (J) Iron frame (1)

ACCESSORIES & QTY ENCLOSED:

• (C) Plastic Wire Connector (3)
• (D) Mounting screw (2)
• (K) Allen wrench (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

3. Unscrew ball knobs (G) from canopy (E) then gently
   remove mounting plate assembly (A).

4. Adjust the length of cord (H) to achieve the desired height of the mounted fixture.

5. Use Allen wrench (K) to unscrew the screw in strain relief (F), carefully pull and push cord (H) through canopy (E) and strain relief (F) to lengthen or shorten the length of cord (H).

6. Once the desired height of fixture is achieved, carefully tighten the screw in strain relief (F) till snug

7. If needed, shorten the extra length of fixture wires from cords (H) so that they all are at least 6 inches (152.4 mm) long above canopy (E) within the outlet box.

6. Carefully pass supply wires through mounting plate assembly (A).
   Secure mounting plate assembly (A) to the outlet box with mounting screws (D).

7. Make wire connections
   Connect wires as below wires connection shown. PLEASE REFER TO THE FOLLOWING CHARTS, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Twist wires together with plastic wire connector (C) until tightly joined, and wrap each connector with approved electrical tape for a more secure connection and carefully tuck all wires into the outlet box. Note: be sure that no wire strands are exposed.

8. Remove ball knobs (G) from mounting plate assembly (A).
   Fix canopy (E) to mounting plate assembly (A) and secure with ball knobs (G).
   Note: canopy (E) should be snug against the ceiling and ball knobs (G). If not, adjust the length of the pre-assembled threaded nipples on mounting plate assembly (A) by unscrewing the pre-assembled hex nuts and then screwing the threaded nipples in or out of mounting plate (A) until the secure length is achieved. Tighten the hex nuts and back to step 8.

9. Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

10. 10. Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

+1 850 296 2377 Working hours : Mon – Fri 9:00 a.m. – 16:00 p.m. EST

uolfin@newdecorworld.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>