Uolfin M7IRFQHD242957R Bathroom Vanity 2 Light Instruction Manual

: June 1, 2024
: Uolfin

Table of Contents

Product Specifications
TOOLS REQUIRED
PARTS INCLUDING
ASSEMBLY & INSTALLATION INSTRUCTIONS
Frequently Asked Questions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Uolfin M7IRFQHD242957R Bathroom Vanity 2 Light

Uolfin-M7IRFQHD242957R-Bathroom-Vanity-2-Light-PRODUCT

Product Specifications

Green ground screw (1)
Mounting plate (1)
Backplate (1)
Knob nut (2)
Arm (1)
Socket (2)
Glass shade (2)
Mounting screw (2)
Plastic wire connector (3)

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instructions carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- B) Place the wall switch in the “OFF” position.
The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

Uolfin-M7IRFQHD242957R-Bathroom-Vanity-2-Light-FIG-1

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Backplate (1)
(F) Knob nut (2)
(G) Arm (1)
(H) Socket (2)
(I) Glass shade (2)

ACCESSORIES ENCLOSED

(A) Mounting screw (2)
(B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position.
Make assembly

Uolfin-M7IRFQHD242957R-Bathroom-Vanity-2-Light-FIG-4

Step A1: Unscrew knob nuts (F) from the back plate (E), then set them aside for later installation.
Step A2: Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3: Make wire connections
Connect wires as below wires connection shown below.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Uolfin-M7IRFQHD242957R-Bathroom-Vanity-2-Light-FIG-5

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in the back plate (E) with the preassembled mounting screws, then attach back plate (E) to the mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.

NOTE : back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled mounting screws in or out of mounting plate (D) until the secure length is achieved.
Tighten the pre-assembled hex nuts and back to Step A4.

Step A5:

Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
Screw glass shades (I) onto sockets (H).

Check everything is installed properly, then you can turn on the light. Enjoy!

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.