Uolfin 5106248 1-Light 11-in Textured Black Lantern Instruction Manual
- June 3, 2024
- Uolfin
Table of Contents
Uolfin 5106248 1-Light 11-in Textured Black Lantern
Item Number: 5106248
WARNING (To reduce the risk of fire, electric shock, or personal
-
Winjury):e suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the OFF position. -
Place the wall switch in the OFFposition.
-
-
Mounting surface should be clean, dry, flat, strong enough and 1/4 larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Back plate (1)
- (F) Arm (1)
- (G) Knob nut (2)
- (H) Lid (1)
- (I) Iron frame (1)
- (J) Screw (3)
- (K) Glass shade (1)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
-
Make assembly
Step A1: Unscrew knob nuts (G) from back plate (E), then set them aside
for later installation.
Step A2: Thread screws (J) through iron frame (I) and lid (H), then
tighten screws (J) to secure glass shades (K).
Step A3: Carefully pass the supply wires from the outlet box through
mounting plate (C). Secure mounting plate (C) to the outlet box with mounting
screws (A).
Step A4: Make wire connections
Connect wires as below wires connection shown.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A5: Align the holes in back plate (E) with the preassembled mounting screws, then attach back plate (E) to mounting plate (C) with the previously removed knob nuts (G). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (G). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (C) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled mounting screws in or out of mounting plate (C) until the secure length is achieved. Tighten the pre- assembled hex nuts and back to Step A5.
Step A6: Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is installed properly, then you could turn on the light. Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>