DEVELCO PRODUCTS MGW211 Squid.link 2B Extremely Flexible LoT Hub Installation Guide

June 3, 2024
Develco Products

DEVELCO-PRODUCTS-MGW211-Squid-link-2B-Extremely-Flexible-LoT-Hub-
logo

DEVELCO PRODUCTS MGW211 Squid.link 2B Extremely Flexible LoT Hub

DEVELCO-PRODUCTS-MGW211-Squid-link-2B-Extremely-Flexible-LoT-Hub-product-
image

Product description

This all-in-one gateway connects smart devices and provides you with monitoring and control functionalities via your smart system. As the gateway is simple to install, you can quickly start to use your smart system and enjoy the connected life.

Disclaimers

CAUTION:

  • Shocking hazard! Do not plug into power if the products have any sign of damage or exposure of wires.
  • Choking hazard! Keep away from children. Contains small parts.
  • Please follow the guidelines thoroughly. The Squid. link gateways are preventive, informing devices, not a guarantee or insurance that sufficient warning or protection will be provided, or that no property damage, theft, injury, or any similar situation will take place. Develop Products cannot be held responsible in case any of the above-mentioned situations occur.
Precautions
  • Do not remove the product label as it contains important information.DEVELCO-PRODUCTS-MGW211-Squid-link-2B-Extremely-Flexible-LoT-Hub-01
Getting started
  1. Connect the power cable to the gateway.
  2. Connect the power adapter to a wall socket.
  3. Connect an Ethernet cable from the gateway to an internet-connected home router.DEVELCO-PRODUCTS-MGW211-Squid-link-2B-Extremely-Flexible-LoT-Hub-02
  4. The LEDs on the front panel are turned on when the system is booting.
  5. The LEDs in the Ethernet connector are turned on and the green LED starts flashing indicating data communication.
  6. After a few minutes, the application is started and the system is ready for use.
Insert sim card

Before installing a sim card into the gateway, disconnect the power cable.

If you have a single sim card and no battery backup:

  • Simply insert the sim card into the card slot on the bottom of the gateway.

If you have dual sim and/or battery backup:

  1. To insert a sim card into your gateway, remove the cover to the sim slot in the battery compartment.DEVELCO-PRODUCTS-MGW211-Squid-link-2B-Extremely-Flexible-LoT-Hub-03
  2. Disconnect and remove the battery (if equipped)
  3. Slide the sim card into the sim card slot. If your gateway is a dual sim gateway and you only want to install one sim card, please install it in the sim card slot marked as number 1.DEVELCO-PRODUCTS-MGW211-Squid-link-2B-Extremely-Flexible-LoT-Hub-04
  4. Reinstall and connect the battery (if equipped)
  5. Reinstall the cover and reattach the screw to fasten it.

Installation of antennas

WHIP ANTENNA
If your gateway comes with a whip antenna, screw it on as shown in the illustration below. Do not over-tighten!DEVELCO-PRODUCTS-MGW211-Squid-link-
2B-Extremely-Flexible-LoT-Hub-05

If your gateway already came with the antenna screwed on, skip, and adjust the angle of the antenna as below.

For the best reception, make sure the antenna faces the centre of the room, and not directly into a wall/concrete. Avoid placing it in a way in which it presents an obstacle to users.

EXTERNAL DIVERSITY ANTENNA
If your gateway includes an external diversity antenna, it needs to be screwed on next to the battery compartment on the bottom of the gateway.
Screw it on as shown in the illustrations below. Do not over-tighten!

Place the antenna as high as possible in the room.

Resetting
Reset the gateway to avoid abnormal behavior by removing the power supply for a few minutes before reapplying it. In case the gateway does not start up, follow the steps below to reset the gateway to the factory setting.

STEPS FOR RESETTING

  1. Use a pen and hold down the reset button as indicated in the picture.
  2. Release the pen again when the LED on the front panel starts to flash continuously.
  3. The system will reboot and after a few minutes the application will be started again.

Battery replacement

If your gateway includes a battery backup, you can replace the battery in the following way.

CAUTION:

  • Do not attempt to recharge or open the batteries.
  • Risk of explosion if batteries are replaced by an incorrect type.
  • Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion
  • Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas
  • Maximum operation temperature is 50°C / 122°F
  • If you experience leakage from the batteries, immediately wash your hands and/or any affected area of your body thoroughly!

CAUTION: When removing cover for battery change – Electrostatic Discharge (ESD) can harm electronic components inside

  1. Open the battery compartment of the gateway with a screwdriver.
  2. Remove the battery from its place within the compartment.
  3. Disconnect the battery and connect the new one. The gateway uses a Li Pol (3,8 V / 2000 mA) battery.
  4. Insert the new battery in its space in the compartment and tuck the cables over or under the battery.
  5. Close the battery compartment and reattach the screw to fasten it.
Disposal
  • Dispose the product properly at the end of life. This is electronic waste which should be recycled.
  • This gateway optionally includes a Lithium battery. Please dispose of the battery according to your local regulations.

CE certification

The CE mark affixed to this product confirms its compliance with the European Directives which apply to the product and, in particular, its compliance with the harmonized standards and specifications.

IN ACCORDANCE WITH THE DIRECTIVES

  • Radio Equipment Directive (RED) 2014/53/EU
  • RoHS Directive 2015/863/EU amending 2011/65/EU
Other certifications
  • Zigbee 3.0 certified.

FCC Regulatory Compliance

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Regulatory Compliance

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Wireless communication

Zigbee:

  • Frequency: 2.4 GHZ
  • Output power: Up to +12 dBm “Declaration for EU Compliance”

WLAN:

  • Frequency: 2.4 GHZ
  • Output power: Up to +20 dBm “Declaration for EU Compliance”

Z-Wave:

  • Frequency: 868
  • Output power: Up to +4 dBm “Declaration for EU Compliance”

Wireless M-Bus:

  • Frequency: 868
  • Output power: Up to +12 dBm “Declaration for EU Compliance”

Bluetooth Low Energy:

  • Frequency: 2.4 GHZ
  • Output power: Up to +12 dBm “Declaration for EU Compliance”

EU Declaration of Conformity

Hereby, Develco Products A/S declares that this radio equipment is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: https://www.develcoproducts.com/products/gateways /squidlink-2x (for model MGW211-DP49 ) and https://www.develcoproducts.com/products/gateways/squidlink-2b (for model MGW221-DP29).

All rights reserved.
Develco Products assumes no responsibility for any errors, which may appear in this manual.
Furthermore, Develco Products reserves the right to alter the hardware, software, and/ or specifications detailed herein at any time without notice, and Develco Products does not make any commitment to update the information contained herein.

All the trademarks listed herein are owned by their respective owners.

Copyright © Develco Products A/S

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Develco Products User Manuals

Related Manuals