DEVELCO PRODUCTS H6500113 Wireless Keypad Installation Guide

DEVELCO PRODUCTS H6500113 Wireless Keypad Installation

Keypad

INSTALLATION MANUAL

Product description

The Keypad includes a tag reader and allows you to enable and disable an alarm system. The Keypad detects when a person is within operating distance, which will make it light up in the dark. The Keypad includes a tamper switch, making it ideal for security purposes.

Disclaimers

CAUTION

• Choking hazard! Keep away from children. Contains small parts.
• Please follow the guidelines thoroughly. The Keypad is a preventive, informing device, not a guarantee or insurance that sufficient warning or protection will be provided, or that no property damage, theft, injury, or any similar situation will take place. Develco Products cannot be held responsible in case any of the above-mentioned situations occur

Precautions

• Do not remove the product label as it contains important information.
• Be aware that electronics are sensitive to static electricity, so aim to discharge before touching, and avoid touching any components inside the device.
• Do not paint the device.
• Do not use tape for mounting the device outdoors.
• Do not use tape for mounting if you will use the device for security purposes, as the tamper switch will not function.
• When mounting with tape, make sure the surfaces are clean and dry.
• When mounting with tape, the room temperature should ideally be between 21° C and 38° C and minimum 16° C.
• Avoid mounting with tape on rough, porous or fibered materials such as wood or cement, as they reduce the tape bond.

Placement

• You can place the Keypad both indoors and outdoors in 0-50 degrees °C.
• Place the device, so it is easily accessible to users.
• Avoid placing the device in direct sunlight.
• Avoid placing the device in places exposed to direct rain.
• Avoid placing moving items 40 cm or less from the Keypad, as they will activate the presence sensor.
• When mounting the device outdoors, use screws rather than tape.

Getting started

1. Open the casing of the device by removing the screw at the bottom of the device.
2. Use the included screws to mount the back plate of the device on the wall
3. Alternatively, you can use the double adhesive tape to mount the backplate. Make sure to press firmly on the backplate with the tape to make it stick.
4. Insert batteries into the device respecting the polarities.
5. When the batteries are inserted, the Keypad will start searching (up to 15 minutes) for a Zigbee network to join. While the Keypad is searching for a Zigbee network to join, the yellow LED flashes.
6. If the scanning has timed out, a short press on the menu button inside the device will restart it.
7. After connecting the device to a network, attach the device to the back plate by hooking the device to the top of the back plate and pushing the device against the back plate.
8. Finally, reinsert the screw at the bottom of the device

Resetting

Resetting is needed if you want to connect your Keypad to another gateway or if you need to perform a factory reset to avoid abnormal behavior

STEPS FOR RESETTING

1. Open the casing of the device by removing the screw at the bottom of the device.
2. Press and hold the menu button inside the device with a thin pin – e.g. a paper clip
3. While you are holding the button down, the LED first flashes once, then two times in a row, and finally numerous times in a row.
4. Release the button while the LED is flashing numerous times in a row.
5. After you release the button, the LED shows one long flash, and the reset is completed.

Battery replacement

CAUTION

• Do not attempt to recharge or open the batteries.
• Risk of explosion if batteries are replaced by an incorrect type.
• Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas
• Maximum operation temperature is 50°C / 122°F
• If you experience leakage from the batteries, immediately wash your hands and/or any affected area of your body thoroughly

CAUTION

When removing cover for battery change – Electrostatic Discharge (ESD) can harm electronic components inside

1. To replace the batteries, remove the screw at the bottom of the device and open the casing.
2. Replace all four batteries inside the device, respecting the polarities.
3. Reattach the device to the backplate and reinsert the screw at the bottom of the device

Fault finding and cleaning

• In case of a bad or wireless weak signal, change the location of the device. Otherwise you can relocate your gateway or strengthen the signal with a smart plug.
• If the search for a gateway has timed out, a short press on the button will restart it.

Disposal

Dispose the product and batteries properly at the end of their lives. This is electronic waste which should be recycled

FCC statement

Changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio

TV technician for help.
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

IC statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. d’exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

ISED statement

Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B).

CE certification

The CE mark affixed to this product confirms its compliance with the European Directives which apply to the product and, in particular, its compliance with the harmonized standards and specifications

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED) 2014/53/ EU
• RoHS Directive 2015/863/EU amending 2011/65/EU
• REACH 1907/2006/EU + 2016/1688

All rights reserved

Develco Products assumes no responsibility for any errors, which may appear in this manual. Furthermore, Develco Products reserves the right to alter the hardware, software, and/ or specifications detailed herein at any time without notice, and Develco Products does not make any commitment to update the information contained herein. All the trademarks listed herein are owned by their respective owners Distributed by Develco Products A/S
Tangen 6 8200 Aarhus Denmark Copyright © Develco Products A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>