Dimplex TLC20LX-AU Toluca Deluxe Wall Mounted Electric Fire Heater Instruction Manual
- June 3, 2024
- Dimplex
Table of Contents
Dimplex TLC20LX-AU Toluca Deluxe Wall Mounted Electric Fire Heater Instruction Manual
The product complies with the Australian Safety Standards and the Standard Electromagnetic Compatibility.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: If the appliance is damaged, check immediately with the supplier before installation and operation. Do not use this appliance in the immediate surroundings of a bath, shower or swimming pool. Do not use outdoors. This appliance must not be located immediately above or below a fixed socket outlet or connection box.
WARNING: The appliance carries the Warning Symbol indicating that it must not be covered or has a Do not cover label. Do not cover or obstruct in any way the heat outlet grille located above the flame window on the appliance Overheating will result if the appliance is accidentally covered. Do not place material or garments on the appliance, or obstruct the air circulation around the appliance, for instance by curtains or furniture, as this could cause overheating and a fire risk. In the event of a fault unplug the heater. Unplug the appliance when not required for long periods. The supply cord must be placed on the right hand side of the heater away from the heat outlet underneath the appliance. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintained shall not be made by Children. Children should be kept away unless continuously supervised. Children shall not plug in, regulate and clean the appliance or perform user maintained. The appliance must be positioned so that the plug is accessible. If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly qualified person in order to avoid a hazard.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
CAUTION – Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. WARNING: The heater must not be used if the glass panels are damaged. Do not use this heater with a programmer, timer, separate remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
General
Unpack the heater carefully and retain the packaging for possible future use,
in the event of moving or returning the fire to your supplier. The fire
incorporates a flame effect, which can be used with or without heating, so
that the comforting effect may be enjoyed at any time of the year. Using the
flame effect on its own only requires little electricity. Before connecting
the heater check that the supply voltage is the same as that stated on the
heater.
Please note: Used in an environment where background noise is very low, it may
be possible to hear a sound which is related to the operation of the flame
effect. This is normal and should not be a cause for concern.
Electrical Connection
WARNING: THIS APPLIANCE MUST BE EARTHED This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage. Before switching on, please read the safety warnings and operating instructions.
Operating Instructions:
Please see Fig. 3
User Modes:
Remote Control – See Fig. 3
maximum range of use is ~ 5metres. NOTE: It takes time for the receiver to
respond to the transmitter. NOTE: The reciever for the remote control is
located in the display, aim the remote control in this direction when
inputting commands. Do not press the buttons more than once within two seconds
for correct operation.
Battery Information – See Fig. 3
- To activate the remote control remove the clear battery isolation strip at the base of the remote control, which is used to ensure your remote control reaches you fully charged. 2. To replace the remote control battery, turn over the remote control, and follow the diagram embossed on the remote control 3. Only use CR2025 or CR2032 size of batteries.
WARNING – KEEP BATTERIES OUT OF REACH OF CHILDREN
- Swallowing may lead to serious injury in as little as 2 hours or death, due to the chemical burns and potential perforation of the oesophagus.
- If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Information Centre on 13 11 26 (in Australia) or 0800 764 766 (in New Zealand) for fast, expert advice.
- Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if the compartment is not secure.
- Dispose of used button batteries immediately and safely. flat batteries can still be dangerous.
Wireless Speaker Control.
The unit needs to be in standby for the speaker function to operate, you do
not need the flame effect to be operating. The speaker can be used in 2 ways.
You can pair a suitable device to the speaker wirelessly and listen to music,
audio books or casts from a suitable device, or when the flame effect is
operating the soothing crackling sound of a log fire can be played for ambient
sound effect.
To listen to the crackling log effect, just press the volume up button on your remote control until you reach a volume level which is comfortable for you, to lower the volume press the volume down button. The crackling is turned OFF by pressing the volume down button until the sound is muted.
To use the speaker to listen to your own material the speaker must first be paired to a compatible device. To pair with the unit:
- Ensure the unit is plugged in and switched on at the mains socket.
- Using a compatible device search for “DImplex Fire”, select and pair your device to “DImplex Fire”.
- Once connection is made between your device and the unit an electronic tone will sound to alert you the pairing was successful.
With the unit now paired you can control the speaker volume using the volume buttons on the remote control handset or your device’s volume controls.
Note: If you experience problems pairing to the speaker, you may need to re- pair to the speaker, follow these steps:
- On your device go to the Bluetooth Settings.
- Select the “Dimplex Fire” and press “Forget” to disconnect from the speaker.
- Turn Bluetooth OFF, and then ON. Your device should now rediscover “Dimplex Fire” again.
- Select “Dimplex Fire” to pair with the speaker.
Installation
WARNING: FALLING OR TIPPING APPLIANCES CAN CAUSE INJURY OR DEATH OF YOUNG CHILDREN, PLEASE ENSURE CHILDREN DO NOT CLIMB, HANG OR STAND ON THIS PRODUCT.
WARNING: THE APPLIANCE IS PROVIDED WITH A WALL FIXING KIT, THIS KIT IS
DESIGNED TO HOLD THE PRODUCTS WEIGHT, IT IS NOT A SUBSTITUTE FOR PROPER ADULT
SUPERVISION. DO NOT ALLOW CHILDREN TO CLIMB OR HANG ON THIS PRODUCT.
Safety Message – Sufficient expertise is required for installing this product.
If unsure we recommend that you use an installer and pay special attention to
safety during the installation.
Wall Installation- See Fig. 2
Do not connect appliance until properly fixed to the wall and the Instruction
leaflet is fully read. In particular, the minimum distances must be observed.
The wall plugs supplied with this product are for use with Block/ Brick built
walls only.
This model is designed to be permanently fixed to a wall at a minimum height of 300mm. The wall bracket must be fitted horizontally and the cable routed to the bottom right of the appliance.
A height of 600 to 725mm from bottom of the appliance to floor is recommended for optimum viewing of fuel bed.
For optimum viewing, mark the top three screw fixing positions on the wall in accordance with the recommended fixing dimensions – see Fig. 2. Drill holes with a 6mm drill bit. Fix the wall bracket using the plugs and screws provided. Carefully lift the appliance up ensuring that the appliance engages with the wall bracket correctly.
A bottom fixing bracket is supplied with the unit, fixed to the base of the appliance. Remove the screw and the bracket, turn the bracket through 180 degrees so it is now facing downward and re fit using the screw just removed. With the bracket in place mark the location of the hole on the wall. Remove the appliance, drill the wall, fit the wall plug and re-fit the appliance ensuring that you secure it in place by screwing the bottom fixing bracket to the wall.
Fuel Bed Media
Acrylic Ice Crystals and White Pebbles are supplied in the box with your fire.
allowing you the option of which to place on your fire. To Fit the Acrylic Ice
Crystals, place the small Crystals on the fuel bed tray, then place the larger
crystals on top of the small pieces. Arrange the larger pieces to your liking.
A suggestion is to place one large crystal centrally on the fuel bed and the
other four positioned symmetrically around this piece. The White pebbles are
placed on the fuel bed tray until the tray is completely covered by pebbles to
your liking.
Fitting the Front Glass- See Fig. 5
Your new fire is supplied with the front glass not secured to the engine, this
is to keep the glass safe in transit. To fit the glass to your fire, simply
insert the four hangers on the back of the glass through the slots provided on
the chassis. The hangers go in through the slots and then move down to hold
the glass in place. The glass can then be secured in place by inserting the
small black screw provided through the hole in any one of the hangers into the
side of the unit.
Thermal Safety Cut-out
The built-in overheat cut-out switches the appliance off automatically in the
event of a fault. If this occurs switch off the appliance or disconnect the
mains plug from the socket. After a short cooling down phase, the appliance is
ready for use again. If the fault should occur again, see your local dealer.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) bulbs in place of
traditional incandescent bulbs. These generate the same light levels as
traditional bulbs, but use a fraction of the energy consumed. These bulbs
cannot be replaced.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. For general cleaning use a soft clean duster never use abrasive cleaners. The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners. To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater. WARNING: do not operate the product without the grille and outer glass in position as this may effect the operation of the heater.
Recycling
At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.
Servicing
Except for installation and cleaning described in this manual, an authorized service representative should perform any other servicing.
Glen Dimplex Australia 8 Lakeview Drive, Scoresby, VIC 3179, Australia
www.dimplex.com.au
[email protected]
Ph: 1300 556 816
Glen Dimplex New Zealand Pty Ltd. 38 Harris Road, East Tamaki, Auckland 2013
New Zealand
www.dimplex.co.nz
[email protected]
Ph: 0800 66 2824
© Glen Dimplex Heating & Ventilation. All rights reserved. Material contained in this publication may not be reproduced in whole or part, without prior permission in writing of Glen Dimplex Heating & Ventilation.