PQL 918XX LED Linear T8 Plug and Go Instruction Manual
- June 3, 2024
- PQL
Table of Contents
PQL 918XX LED Linear T8 Plug and Go
INSTALL INSTRUCTIONS
DO NOT INSTALL THIS LAMP IN A PRE-HEAT LUMINAIRE.
THIS LAMP ONLY OPERATES ON ELECTRONIC BALLASTS. IF THE LAMP DOES NOT LIGHT
WHEN THE LUMINAIRE IS ENERGIZED, REMOVE THE LAMP FROM THE LUMINAIRE AND
CONTACT THE LAMP MANUFACTURER OR QUALIFIED ELECTRICIAN.
CAUTION RISK OF FIRE – IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE
OPERATION (BUZZING, FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE THE
LAMP FROM THE LUMINAIRE, AND CONTACT THE MANUFACTURER.
SAFETY INFORMATION
- Check the lamp before installation, if there is any damage caused during transportation, do not install it.
- Maintenance should be carried out by qualified personnel only.
- Do not stare at the light source with bare eyes for a long time, or beam into another person’s eyes.
- Do not place any objects on the lamp.
- Keep the lamp away from flame or high-temperature objects.
- Risk of electrical shock. Only replace it with the same type of LED tube.
- If the glass lamp tube is broken, the lamp must be disposed of immediately.
MAINTENANCE NOTES
- Disconnect the lamp from the power supply before any maintenance.
- Clean the luminaire with a dry cloth.
- Do not clean the lamp with corrosive chemicals.
- FOR EMERGENCY LIGHTING ONLY WITH BALLAST – Listed (FTBR/7), PHILIPS EMERGENCY LIGHTING (E49328), Model B50 (Alternate RS), Rated 120/277V – 50/60Hz, Damp Location Fluorescent Emergency Ballast.
- Ensure the temperature of the Tc point is under 131°F after the lamp has been working properly for 2 hours, otherwise, the performance of the lamp might not comply with
specifications.
This product may cause interference to radio equipment and should not be
installed near maritime safety communications equipment or other critical
navigation or communication equipment operating between 0.45-30 MHz.
SAFETY PRECAUTIONS
WARNING: Risk of Shock. Disconnect power before installation.
LED T8 lamp for use only with products described and installed in accordance
with product specifications. LED T8 lamp to be operated with fluorescent
electronic ballast, emergency ballasts, and dimming ballast.
WARNING: RISK OF FIRE, USE ONLY IN PLACE OF FLUORESCENT LAMPS SPECIFIED ON
THE LABEL. RISK OF ELECTRIC SHOCK. SUITABLE FOR DAMP LOCATIONS.
Check the ballast compatibility list before installation, only use a lamp with qualified T8 fluorescent ballast.
WARNING DISCONNECT POWER BEFORE INSTALLING OR SERVICING.
-
Make sure the power is OFF.
-
Remove the lens or diffuser (if applicable).
-
Remove existing fluorescent lamps from the luminaire.
-
Bring LED lamp to luminaire and insert lamp pins into luminaire lamp holders.
-
Rotate the LED lamp until the lamp locks in place. Ensure that the LED lamp front points away from the back of the luminaire.
Note: Install one LED T8 replacement lamp for each fluorescent lamp removed. -
Place the lens or diffuser back in place (if applicable).
-
Power On.
INSTANT START BALLAST WIRING DIAGRAMS
CORRECT
- TWO LAMP BALLAST WIRING
- CORRECT
- THREE-LAMP BALLAST WIRING
- CORRECT
- FOUR-LAMP BALLAST WIRING
- CORRECT
- INSTANT START BALLAST WIRING DIAGRAMS INCORRECT
- TWO LAMP BALLAST WIRING
- INCORRECT
- FOUR-LAMP BALLAST WIRING
- INCORRECT
- PREMIUM QUALITY LIGHTING®
- www.PQLighting.com
- © P.Q.L., Inc.
- 2285 Ward Avenue
- Simi Valley, CA 93065
- 800-323-8107
- Specifications are subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.
Documents / Resources
| PQL
918XX LED Linear T8 Plug and
Go
[pdf] Instruction Manual
918XX, LED Linear T8 Plug and Go, 918XX LED Linear T8 Plug and Go, T8 Plug and
Go, Plug and Go
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>