PQL 84080 LED Stadium Lights V2 Instruction Manual
- June 4, 2024
- PQL
Table of Contents
84080 LED Stadium Lights V2
Instruction Manual
LED STADIUM LIGHTS V2
INSTALL INSTRUCTIONS
PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the
instructions before you install and use the luminaire.
GENERAL: ALL ELECTRICAL CONNECTIONS MUST BE IN ACCORDANCE WITH LOCAL AND
NATIONAL ELECTRICAL CODES (N.E.C.) STANDARDS. IF YOU ARE UNFAMILIAR WITH
PROPER ELECTRICAL WIRING CONNECTIONS OBTAIN THE SERVICES OF A QUALIFIED
ELECTRICIAN.
WARNING – Risk of fire or electric shock. Installation requires knowledge
of luminaire electrical systems. If not qualified, do not attempt
installation; contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install luminaires that have
the construction features and dimensions shown in the photographs and/or
drawings and where the voltage input rating of does not exceed the voltage
input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to
the edges of sheet metal or other sharp objects. Do not make or alter any open
holes in an enclosure of wiring or electrical components during installation.
Risk of Electric Shock: Disconnect power or circuit breaker before installing
or servicing. Before installation, please check if the local voltage range
corresponds with the working voltage of the fixture. If the fixture is
damaged, it should be replaced by the supplier, a service agent or a qualified
person. Do not use it when exposed to flame, electric shock, or high
vibration.
WARNING DISCONNECT POWER BEFORE INSTALLING OR SERVICING.
300W / 400W / 500W / 600W
STEP 1 – Attach the glare shield to the luminaire body by using the
M5x12mm screws to lock the shield in place.
STEP 2 – MOUNTING LUMINAIRE
- Place the fixture on the mounting surface.
- Insert M20 and M10 bolts into the bracket. Tighten the bolts hand tight so the luminaire is secured to the mounting surface but still allows adjustment. Do not fully torque down until the desired position is set.
- Adjust bracket and fixture vertically, and for Install Method 1 horizontally.
- Fully tighten all bolts to secure the fixture. General Wiring Diagram on Page 2.
MOUNTING DIAGRAM
OPTIONAL U-BRACKET WITH SLIP FITTER
FOR 300W / 400W / 500W / 600W (Item# 84080, sold separately)
MOUNTING LUMINAIRE
- A secure fixture in U-Bracket.
- Place slip fitter on a light pole. Tighten the bolt’s hand tight so the luminaire is secure but allows adjustment.
- Adjust fixture to the desired angle.
- Fully tighten all bolts to secure the fixture. General Wiring Diagram on Page 2.
WARNING DISCONNECT POWER BEFORE INSTALLING OR SERVICING.
**750W / 1250W*
STEP 1 – Attach the glare shield to the luminaire body by using the
M5x12mm screws to lock the shield in place.
STEP 2 –** MOUNTING LUMINAIRE
- Place the fixture on the mounting surface.
- Insert M20 and M10 bolts into the bracket. Tighten the bolts hand tight so the luminaire is secured to the mounting surface but still allows adjustment. Do not fully torque down until the desired position is set.
- Adjust bracket and fixture vertically, and for Install Method 1 horizontally.
- Fully tighten all bolts to secure the fixture.
*Note: The 1250W Stadium Light uses an external driver box. The driver box should be mounted within 85′ of the fixture to prevent voltage loss.
MOUNTING DIAGRAM
GENERAL WIRING DIAGRAM
*Note: For non-dimming applications, cap the purple and gray dimming wires separately. Failure to do so may cause malfunctioning and void warranty.
PREMIUM QUALITY LIGHTING®
www.PQLighting.com
© P.Q.L., Inc.
2285 Ward Avenue
Simi Valley, CA 93065
800-323-8107
Specifications subject to change without notice.
Photos and line drawings may not be to scale and are for general reference
only.