PQL 55241 LED Spec-Select Designer Strip Instruction Manual

: June 4, 2024
: PQL

Table of Contents

PQL 55241 LED Spec-Select Designer Strip
SURFACE MOUNTING
GENERAL WIRING DIAGRAM
CHAIN MOUNTING WITH V-HOOK
FIELD ADJUSTABLE WATTAGE & CCT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PQL 55241 LED Spec-Select Designer Strip

PQL-55241-LED-Spec-Select-Designer-Strip-product

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.

WARNING, CAUTIONS, AND OPERATING INSTRUCTIONS

To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
Commercial installation, service, and maintenance of luminaires should be performed by a qualified licensed electrician.
For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING: RISK OF FIRE OR ELECTRICAL SHOCK

Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
Turn off the power when you perform any maintenance.
Verify that the supply voltage is correct by comparing it with the luminaire label information.
All wiring connections should be capped with UL-approved wire connectors.

CAUTION: RISK OF INJURY

Avoid direct eye exposure to the light source while it is on.
Account for small parts and destroy packing material, as these may be hazardous to children.
Risk of burn. Disconnect power and allow the fixture to cool before changing the bulb or hanging the fixture.
Green ground screw provided in the proper location. DO NOT RELOCATE.
Minimum 90° supply conductors.
Suitable for Dry or Damp locations.

WARNING
TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.

SURFACE MOUNTING

Secure the provided brackets onto the ceiling by using the provided accessories and screws. (Fig. 1)
Screw the covers at the outlet to the back of the housing. (Fig. 2)
Wire to the main power through the junction box. (Fig. 3)
Then clip the brackets to the slots of the fixture. (Fig. 4)

LENS INSPECTION:
After installation check to make sure the lens is completely secure, snapped inside the entire length of the lamp body, and fitted under the end cap. Gently pull down on the lens to ensure it does not shift.

GENERAL WIRING DIAGRAM

PQL-55241-LED-Spec-Select-Designer-Strip-fig-5

WARNING – TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER WARNING – TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER.

CHAIN MOUNTING WITH V-HOOK

Clip the brackets to the slots of the fixture. (Fig. 5)
Attach customer-supplied V-hooks to brackets.
Attach a customer-supplied chain to the V-hooks and mounting surface.

LENS INSPECTION:
After installation check to make sure the lens is completely secure, snapped inside the entire length of the lamp body, and fitted under the end cap. Gently pull down on the lens to ensure it does not shift.

FIELD ADJUSTABLE WATTAGE & CCT

The end users may adjust the color temperature and wattage, respectively, by the two slide switches integrated into the side of the fixture. Each switch has 3 options (left, middle, and right ), each position corresponds to 1 of 3 color temperatures (Warm White, Cool White, and Sky-Brite®) and 1 of 3 wattages, which can be adjusted to the desired combination.

Switches are located on the side of the fixture. (Fig. 6).
Select a wattage and color temperature by sliding the switch left or right respectively to the desired value. (Fig. 6).