FLASH PROFESSIONAL P7110029 Square 250 IP LED PAR User Manual

: June 3, 2024
: FLASH PROFESSIONAL

Table of Contents

FLASH PROFESSIONAL P7110029 Square 250 IP LED PAR
INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
CONNECTIONS
OPERATION MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH PROFESSIONAL P7110029 Square 250 IP LED PAR

FLASH-PROFESSIONAL-P7110029-Square-250-IP-LED-PAR-PRODUCT-
IMAGE

INTRODUCTION

Thank you for purchasing SQUARE 250 IP. For safety reasons and to ensure the trouble-free operation, carefully read the instructions.

SAFETY INFORMATION

Installation should be done by qualified personnel in order to minimize the risk of accidental electric shock
Disconnect the power supply before installation.
Before connecting the unit to the mains, make sure it is not damaged mechanically. If you notice any signs of damage you should contact your dealer immediately. Do not connect the device to the mains.
Do not use the device in high humidity conditions and at temperatures above 40° C
The device must be installed on stable structures
Always use steel security cable to attach the device to a stable structure
Do not connect power supply to more than 4 devices in series.

PRODUCT INFORMATION

Features

Dedicated Color Temperature Correction channel (CTC)
2200K to 5200K color temperature (warm to natural white)
16-bit dimming resolution
Various dimming curves for smooth dimming in 8-bit mode
Dim delay (light bulb simulation)
Full DMX signal regeneration
Electronic protection against overheating
THEATRE or DISCO cooling volume modes.
Permanent color correction
Native support for optional wireless DMX module

Specification

Power consumption: 250W
Power supply voltage: 100 – 245V
Voltage frequency: 50/60Hz
Diode type: 2xWhite COB
Number of diodes: 1
Diode power: 250W
Display: Color LCD
Color: Warm white (2200K), natural white (5200K)
Beam angle (min): 37°
Beam angle (max): 37°
Dimming: Linear: 0 – 100%
Flash frequency (min): 1Hz
Flash frequency (max): 20Hz
DMX standard: DMX 512
Control interface: 4 buttons
Operating modes: DMX512, Auto, Sound-controlled, Master / Slave
Features: 16-bit dimming, various dimming curves, bulb simulation, DMX Signal regeneration, Electronic protection against overheating
AC IN: power CON
AC OUT: power CON
DMX IN: XLR – 3 pin
DMX OUT: XLR – 3 pin
IP Rating: IP20
Housing made: ABS
Cooling: Active
Height [cm]: 28
Width [cm]: 27
Depth [cm]: 24
Weight [kg]: 3,4
Weight with packaging [kg]: 4,2

INSTALLATION

After removing the packaging, check if the device was not damaged during transport. Before connecting to the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage caused by unstable mounting.

CAUTION! Always use steel security cable to attach the device to a stable structure.
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are consistent with device requirements. All activities, including connecting the device to the mains must be performed by qualified personnel.

CONNECTIONS

The device is equipped with the following interfaces:

DMX (in/out): XLR 3-pin socket
Power (in/out): powerCON socket

Connecting DMX signal

The connection is performed using cable with XLR-female -> XLR-Male plugs.

Voltage specification

Input Voltage	Total Power	Frequency
100~245V	250W	50/60Hz

Connecting power supply

The connection is performed using power cable with PowerCon connector (included).
The device must be operated by qualified personnel. Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.
Maximum number of devices connected in series: 4