Uolfin 4978092 3-Light Matte Black and Teardrop Glass with Wood Farmhouse Clear Glass Linear Pendant Light Installation Guide

Uolfin 4978092 3-Light Matte Black and Teardrop Glass with Wood Farmhouse

Clear Glass Linear Pendant Light

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8.  When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PART LIST

PARTS TYPE & QTY INCLUDING:

• (C) Single bar (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Loop (4)
• (G) Quick link (4)
• (H) Hex nut (1)
• (I) Cap nut (1)
• (J) Chain (2)
• (K) Fixture body (1)
• (L) Socket (3)
• (M) Screw (9)
• (N) Glass shade (3)

ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)
• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre­installation

  *  **Step A1:** By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
  *  **Step A2:** Open quick links (G). Attach quick links (G) to loops (F) on canopy (E) and fixture body (K). Close quick links (G).
  *  **Step A3:** Carefully weave the fixture wires through chain (J) in and out of every other link and stop just when you reach the top of chain (J). Gently pull the wires to ensure the wires are not stressed.

3. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

4. Make installation

  *  **Step B1:** Unscrew hex nut (H) and cap nut (I) from single bar (C).
  *  **Step B2:** Attach single bar (C) to the outlet box with mounting screws (B).  

Note: the side of single bar (C) marked “GND” must face out.

  *  **Step B3:** If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.
  *  **Step B4:** Make wire connections  

Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart

**Connect wires according to the below chart

Note:** When parallel wires (SPTI & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  *  **Step B5:** Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening hex nut (H) and cap nut (I) onto the pre­assembled threaded nipple.
  *  **Step B6:**
  1. Place glass shades (N) on sockets (L) and secure them with screws (M).
  2. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

5. Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING.

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS.

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

ABOUT COMPANY

• +1 850 296 2377
• Working hours : Mon ­ Fri 9:00 a.m. ­ 16:00 p.m. EST
• uolfin@newdecorworld.com

References

• HOMEANGEL LLC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>