Aobosi AMR520 Slow Masticating Juicer Instruction Manual
- June 14, 2024
- Aobosi
Table of Contents
Aobosi AMR520 Slow Masticating Juicer
Parts and functions
Section I. Precautions for Safety Use
When using electrical appliances, basic safety precautions should always be followed, including the following:
- Power of 220-240V~50/60Hz shall be supplied to this product. Please confirm your power supply before use.
- Be sure to disconnect the power supply before dis-assembly/reassembly or adjustment to this product.
- In case of any damage to the flexible wire, to avoid any hazard, contact our customer service or send it to our authorized service center for replacement, and do not try to disassemble it without our authorization.
- Prior to use, please check the power cable, plug, juice filter, Auger, chopper body, meat grinder and other parts, and in case of any damage, stop using this product and contact our customer service immediately without unauthorized dis-assembly or repair to avoid any potential hazard.
- For need of any repair during use,return appliance to our authorized service facility for examination, repair or electrical adjustment.
- Before connecting with power supply, make sure that any such removable parts as extractor body, auger, juice filter and extractor cover have been mounted in place.
- DO NOT put your fingers or other objects into the juicer openingwhile it is in operation. If food becomes lodged in the opening, use the plunger or another piece of fruit to push it down. When this method is not possible, turn the motor off and disassemble juicer to remove the remaining food.
- The food material needs to be cut into proper pieces so as to pass through the inlet to extractor/chopper/grind. Any fruiVvegetable shall haveanyhardcore,seed,skinorshell removed before processing.
- Proper amount of force shall be used to push the food material in, not excessive but sufficient to have it cut off exactly.
- The juice filter, extractor cover, or auger may be dyed by the juice during operation, which is a normal phenomenon and has no effect on edibility and does no harm to health.
- This product is equipped with intelligent protection chips, making it stop automatically for every 20 minutes’ operation. And in such case, rest it for 20-30 minutes before restarting it, so as to cool the motor down and prolong product servicelife.
- This product is designed to limit the flow rate. During processing of any hard material, the motor will be locked and the current will rise up. When the current goes higher than 1.3A, the equipment will beep and the motor will stop operation for over-current protection and extension of life span.
- In case that current limit protection is triggered or the motor is locked and stops automatically, disconnect the power supply and keep the switch in position “0”, and press Rotate Backwards button on the power switch, and then discharge the food material and then press Rotate Forwards to restart the machine. If the problem continues, it is recommended to remove any food material inside auger before restart so as to protect the motor.
- After the completion of operation, remove any removable part only after the motor/auger/shredder/slicer/grinder screw has stopped rotating and the power has been disconnected.
- Any part in contact with food material is clean, safe and reliable in compliance with related food hygiene codes.
- To protect against risk of electrical shock, do not put the motor base in water or other liquid.
- Do not use any steel wool, abrasive cleaning agent or corrosive liquid such as gasoline or acetone to clean this product.
- This product should be stored in a place that children can’t reach. Not allow persons with unsound extremities and sensation or mental disorders and persons who are short of related experience and knowledge( including children ) to use or play with this product.
- This product is used for individual or family only.
- This product is of Class-I protection grade, and the socket used for it must be grounded properly.
- Hazards or unsafe practices could result in minor personal injury or appliance damage. Care shall be taken when handling the sharp cutting blades, emptying the bowl and during cleaning. Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling or cleaning.
Section II:
Component
Name Function Description
Power Cable For connection to power supply.
Housing| The main unit containing motor and other components, providing
poweroutput.
On-Off Switch| For control of product operation, such as
forward/backwardrotation and close-down.
Locking Button| For locking of extractor to prevent unexpected release out of
the housing. To unload the extractor off the housing, press down and hold this
button.
| Juice Container| To hold and collect the juice extracted by the extractor.
| Container
Baffle
| To separate foam from the juice in the container.
| Pomace
Container
| To hold and collect any Pomaces separated by the
extractor.
Plunger| To squeeze and make the load food material
contact completely with the auger so as to maximize extracting efficiency.
Tray| For interim storage of food material to process.
Feed chute| Feeding food and load down to Drum
Drum
| One of the main components to extract juice, where the food material is loaded from the Feed chute at the top, while the juice and Pomaces are
discharged from the outlet.
Auger| One of the main components to extract juice, where
the food material is transferred and ground against juice filter or extruder.
Juicing screen| Work with Auger to grind food material and filter the juice.
(applicable to fruits, vegetables and beams)
End cap| Coupled with extractor to provide protection.
Wrench
| Please use this wrench to remove the juicer cover in clockwise direction if you find the juicer cover is difficult to remove after juicing.
Section Ill. Method of Operation
Prior to first use, Please thoroughly clean any parts in contact with food material. (See Section IV. Maintenance for more details)
Button Operation
- DescrlpUon: ·oN”
- Appliance is ON state
- “O”: Appliance is OFF state
- “R” : Appliance will REVERSE auger.{use when food Is blocking or stuck)
- Tips : In case of Pulp blockage or motor locking. Press and hold”R” button for approximately 3 seconds to rotate the auger reversely and then release it. Press”ON”button lo resume nonnal operation.
- Note : After Press “ON”, the appliance need to pause for 1• before starting working.
Section IV. How to assemble
| 1| Connect Drum 11 with Housing 2:
Connect the Drum 11 with 2 the Housing by aligning the on Feed chute 10 with on the Housing , push the Drum hard and rotate the Drum anticlockwise until aligning on Feed chute)with on the Housing 2.(You will hear “Tick” sound to confirm fasten it tightly and correctly).
---|---|---
| 2| Place the auger 12 into the drum 11.
| 3| Insert the juicing screen 12 into the drum 11.
| 4| Place the end cap@ onto the drum@ end and rotate the cap counter-
clockwise.
---|---|---
| 5| Place Juice Cup@ and Pulp Container(7)under the drum set.
| 6| Mount tray onto the upper end of Feed chute®.
| 7| Connect to power supply and get ready for start up. (Before power-on,
make surethe switch is in Off position.)
**| 8| Clean the material and cut it into pieces small sufficiently whdl
can pass through the Feed chute, and place them onto the tray.
Note** : Any hard core, seed, skin or shell from fruits and vegetables
shall be removed in advance.
| 9| Press down”ON” button on the switch to start Note: Keep the machine
operating for less than 10 minutes. Long time work will destroy the motor.
Note : Do not touch the power switch with wet hand to avoid electric
shock, leakage or fire.
| 10| Place the few pieces of cut fruit or vegetables into the Feed chute, push them down the drum gentlywith plunger.
• Proper amount offorce shall be usedtopush the food material in,not excessive butsufficientto have it cut off exactly. (Do not put your finger or any otherobject into the Feed chute! If the Pulp/Juice Cup is full, disconnect the power supply and clear it up before restart.)
---|---|---
| 11| Upon completion, shut down the switch when no juice flows out of the outlet and disconnect the power supply. Do not remove the Juice Cup off the outlet until the spiral propeller and juice filter have stopped rotating completely. The extracted juice should be drunk as soon as possible as it will have degraded taste and nutrient content if exposed in the air for a time.)
• The Pulps shall not be stored fora long time.
• Do not touch the power switch with wet hand to avoid electric shock, leakage or fire.
Section V. Tips for Ingredients Selection
-
FRUIT JUICE EXTACTOR
Efficiently juices hard and soft fruits: even citrus fruits, usually one of the hardest fruits to juice. Jam can not be achieved, some fruit can not squeeze juice (such as bananas, mangoes, dried fruit, sugar cane, etc.). -
VEGETABLE JUICE
Cut vegetables to strips(less than 10 cm). Juices all kinds of vegetables including carrots, beets, celery, peppers, and radishes without destroying the natural flavor and nutrition benefits. Fresh taste and full nutrition are guaranteed with this unique extraction process. -
WHEATGRASS AND LEAFY GREENS
Cut it to strips(less than 10 cm). Wheat grass, kale, cabbage, spinach and pine tree needles are just some of the natural products that can be juiced with the Aobosi juicer. Enjoy the best that nature offers in raw foods of all kinds and juice them for full nutritional benefits.
Instructions on Selection of Fruits
- Select fresh fruits and vegetables, which contain more juice. The proper fruits include: pineapple, beet root, celery stalk, apple, cucumber, spinach, melons, tomato, orange and grape.
- Thick skin on fruits such as orange, pineapple and raw beet root instead of thin skin on fruit/vegetable needs to be removed. Seeds in oranges should be removed as well, which may make the juice taste a little bitter.
- Concentration of juice extracted from apple depends on what type of apple is selected. Juice extracted from juicier apple is less thick, so select the proper type of apple depending on your desired juice concentration.
- Just extracted apple juice will turn brown very soon, and this process can be slowed by adding drops of lemon juice into it.
- Leaves and stems (such as those of lettuce) can be put into the extractor to extractjuice.
The typical nutrient ingredient contained in fruits/vegetables are shown below:
Fruit/Vegetable | Vitamin/Mineral | Calorie |
---|---|---|
Apple | Vitamin C | 200 gram = 150 KJ (72 calorie) |
Apricot | Dietary fiber and potassium | 30 gram = 85 KJ C 20 calorie) |
Beet | Folic acid, dietary fiber, Vitamin C |
and potassium
| 160 gram= 190 KJ(45 calorie)
Blueberry| Vitamin C| 125 gram = 295 KJ(70 calorie)
Brussels Sprouts| Vitamins C, B, B6 and E, folic acid
and dietary fiber
| 100 gram= 110 KJ(26 calorie)
Cabbage| Vitamin C, folic acid, potassium,
Vitamin B6 and dietary fiber
| 100 gram= 110 KJ(26 calorie)
Carrot| Vitamins A, C and B6, and dietary fiber|
100 gram=110 KJ (26
calorie)
Celery| Vitamin C and potassium|
80 gram = 55 KJ(7 calorie)
Cucumber| Vitamin C| 280 gram = 120 KJ(29 calorie)
Fennel| Vitamin C and dietary fiber| 300 gram= 145 KJ(35 calorie)
Grape| Vitamins C and B6, and potassium| 125 gram = 355 KJ(85 calorie)
Yangtao| Vitamin C and potassium| 100 gram= 100 KJ(40 calorie)
Muskmelon| Vitamins C and A, folic acid and
dietary fiber
| 200 gram= 210 KJ(50 calorie)
Nectarine| Vitamins C and B3, potassium and
dietary fiber
| 180 gram = 355 KJ(85 calorie)
Peach| Vitamins C and B3, potassium and
dietary fiber
| 150 gram= 205 KJ(49 calorie)
Pear| Dietary fiber| 150 gram= 250 KJ(60 calorie)
Pineapple| Vitamin C| 150 gram= 245 KJ(59 calorie)
Raspberry| Vitamin C, iron, potassium and
magnesium
| 125gram=130KJ(31calorie)
Tomato| Vitamins C, E and A, dietary fiber
and folic acid
| 100 gram = 90 KJ(31 calorie)
Section VI. Maintenance
- Before cleaning this product, be sure to shut down the switch to disconnect the power supply.
- Clean this product after using it.
- The Housing cannot be washed underwater, and must be deaned with twisted wet clothinstead.
- Before storing it, make sure this product is clean and dry.
- Disassemble this product to wash the components by the followlng steps:
WARNING: Do not immerse the motor base in water or any other liquid. Do not use water jet to clean the motor base.
Section VII. Safety Index
Rated Voltage | 220V-240 |
---|---|
Rated Power | 150W |
Rated Frequency | 50/60Hz |
Continuous Operating Time | 10 minutes |
Interval time | 10 minutes |
Juice Container 950ml Pulp | Container 800ml |
The device meets the requirements of Regulation 2016 as well as the applicable standards
- EN 60335-2-14: 2006 + A1: 2008 + A11: 2012 + A12: 2016
- EN 60335-1: 2012 + A11: 2014 + A13: 2017 + A1: 2019 + A14:2019 + A2: 2019
- EN 62233: 2008
- BS EN 60335-2-14: 2006 + A12: 2016
- BS EN 60335-1: 2012 + A2: 2019
Section VIII. Trouble Shooting
Fault Phenomenon | Analysis of cause | Fault resolution |
---|
After connecting power supply and turning on the switch, the product fails to work| 1. After turn on the machine, wait for 1s, it will work. It is normal.
2.After 1s, it still no work, maybe poor contact between plug
and socket
| Re-plug it properly
1. Replace the socket and try again, or contact after Sales Support Email: info@iaobosi.com
During the early uses, the motor generates
unpleasant smell
| ****
It is a normal phenomenon
| If this phenomena occurs frequently, send it to our authorized service center
nearestto you for inspection.
This machine stop during operation
| 1. Too low voltage
2. Excessive amount of food material has been loaded
3. The machine has operated continuously for long time.
| 1. Check whether the voltage is too low
2. Disconnect the power supply and remove excessive food material
3. It is a normal phenomenon
and themotorwill resume after a break time.
Noise is generated during operation.
| 1. The machine operates in an unbalanced state due to failure to mount auger or juice filter in place.
2. The starting motor in
theframehasbeen damaged.
| 1. Mount auger or juice filter in place or Contact after Sales Support Email: info@iaobosi.com
Section IX. Warranty
Thank you for choosing AOBOSI product. We sincerely hope that you are satisfied with it. The manufacturer’s warranty covers the product for a period of 24 months from the date of purchase against manufacturing faults. All warranties are automatically kept track of in our system, so there is no need to register your product. Agent/Distributor is welcome to contact us. Email: info@iaobosi.com. Any help or questions during use, please contact us via website www.iaobosi.com , send email to info@iaobosi.com, we will service you within 24 hours. We suggest to provide a warranty card, a photo or a video if there’s broken spare part or not working machine so that we can be much more clear about your problems and offer you the best solution.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>