Lucci 190630 Ledlux Rijks Wall Bracket Instruction Manual

Installation Instructions
LEDLUX RIJKS WALL BRACKET
SKU# 190630, 190631
Rated Voltage 220-240V~ 50Hz

190630 Ledlux Rijks Wall Bracket

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before using the product. Please keep instructions for future reference.

Warranty

• This fitting is covered by a 3 year warranty. The warranty is from date of purchase, not the date of installation.
• If the fitting is not installed by a licensed electrician it will void the warranty.
• Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
• The use of non-recommended dimmers may damage your LED light fitting and will void the warranty.
• Warranty will be void if there is any damage due to improper usage or modification to the fitting.
  Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.

Installation requirements

• Must be installed by a licensed electrician.

• All wiring and installation of the light fitting must adhere to local and national wiring rules. eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.

• This is a CLASS I fitting and must be earthed during installation.

• This fitting is rated IP44 which is protected against splashes of water, this must be maintained during installation.

• Select a suitable location for installation, the mounting point must support 2 times the weight of the fitting.

• This fitting is dimmable and has been tested with Lucci LEDlux SKU# 290998 dimmer, Clipsal 32E450TM, 31E2RUDM and Clipsal 32E450UDM dimmers only. The use of a LED dimmer such as the Lucci LEDlux SKU# 290998 dimmer is highly recommended.
  NOTE: For the best dimming range, use with the Lucci LEDlux SKU# 290998 dimmer and adjust the variable resistor at minimum and maximum dimming positions on the dimmer during the installation.
  NOTE: The use of non-recommended dimmers may damage your LED light fitting and will void the warranty.
  NOTE: Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED light start up or slight uneven light performance when more than one LED light fitting is linked together, switched ON or dimmed. This is not a product fault and as such is not covered under warranty.
  NOTE: Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before turning on the LED light and adjust the dimmer down to your desired light level.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation directions

1. Remove all packaging material from the fitting.
2. Remove the lamp body from mounting bracket by loosening the screws.
3. Use the mounting bracket as a template to mark the screw positions onto the wall. Drill holes into the wall and push plastic anchors into the holes. (Fig. 1)
4. Install the mounting bracket onto the wall by using the mounting screws and rubber rings provided. Check and ensure that the anchors and mounting screws are suitable for the mounting surface.
5. Remove the junction box cover by loosening the 4 screws. (Fig. 2)
6. Connect the earth and mains supply wire to the terminal block. Ensure that the wires are secure and no bare wires are exposed.
   Mains Supply Wire
   Earth – Yellow/Green
   Neutral – Blue or Black
   Live – Brown or Red| Fitting Wire
   Yellow/Green
   Blue
   Brown
   ---|---
7. Reinstall the junction box cover. (Fig. 3)
8. Install the lamp body onto the mounting bracket by securing the 2 screws. (Fig. 4)

Safety tips

• Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning or adjustment to the fitting.
• To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
• Ensure that the fitting does not come in contact with corrosive chemicals, etc.
• To clean, wipe with a damp clean cloth. Never soak the fitting with water.

Specifications

3000K, 1350lm
Dimmer Information| Lucci LEDIux SKU# 290998 dimmer (Highly Recommended);
Clipsal 32E450TM, 31 E2RUDM and 32E450UDM (Compatible);
(Please refer to the Installation Requirements or Troubleshooting section in this manual for more information on the recommended dimmers, performance, operation and tips.)
Weight| 1.35kg| 2kg
Dimensions| H75 x W640 x E6Omm| H75 x W940 x E6Omm
IP Rating| IP44

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>