Lucci LEDlux 181045 Yuma Round Large Flush Mount Instruction Manual

: October 27, 2023
: LUCCi LEDlux

Table of Contents

Lucci LEDlux 181045 Yuma Round Large Flush Mount
Warranty
Installation Requirements
Installation Directions
Safety Tips
Troubleshooting
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lucci LEDlux 181045 Yuma Round Large Flush Mount

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

This luminaire is covered by a 3-year warranty. The warranty is from the date of purchase, not the date of installation.
If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
The use of non-compatible dimmers may damage your LED luminaire and will void your warranty.
Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

This luminaire must be assembled and installed by a licensed electrician.
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules. E. g. AS/NZS 3000 Electrical Installations.
The luminaire is a Class II product and must be maintained during wiring and installation.
Select a suitable location for installation:
- This luminaire is suitable for indoor use only.
- The mounting point must support 2 times the weight of the luminaire.
- Ensure the luminaire is not installed in direct line of an air vent/system.
- If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
This luminaire is dimmable and was tested with the dimmers listed in the specification section at the date of publication. The use of a LED dimmer such as the Lucci LEDlux SKU# 290998 or Lucci LEDlux SKU# 290997 dimmer is highly recommended.
NOTE : For the best dimming range, use the Lucci LEDlux SKU# 290998 dimmer and adjust the variable resistor at the minimum and maximum dimming positions on the dimmer during the installation.
NOTE : Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED luminaire start-up or uneven light performance when more than one LED luminaire is linked together, switched ON or dimmed. This is not a product fault and as such is not covered under warranty.
NOTE : Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before turning on the LED light and adjust the dimmer down to your desired light level.
NOTE : Testing cannot account for installation variables such as variation in mains supply voltage, cable capacitance, electrical noise, transients, surges and ripple control signals (commonly found in NSW & QLD).
NOTE : The information provided is correct to the best of Beacon Lighting’s knowledge at the date of publication.
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure no components are missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

Installation Directions

Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Remove the mounting bracket from the luminaire by loosening the screws on the side.
Use the mounting bracket as a template to mark the screw positions on the ceiling.
Install the mounting bracket onto the ceiling by using appropriately sized mounting screws, flat washers and anchors. Ensure the screws and anchors used are suitable for the mounting surface and the surrounding environment.
Use the switch on the side to select the colour temperature (3000K / 4000K / 5000K) you desire.
Open the cover from the terminal box
Prepare the mains supply wire to make a connection to the terminal block.
NOTE : The bare wire must be no more than 6cm in length.
NOTE : For the remaining mains supply wire basic insulation, use the sleeve tube provided with the terminal box to ensure double insulation is achieved.
Connect the mains supply wire to the terminal block. Ensure the wires are secure and no bare wires are exposed.
Mains Supply Wire Luminaire Wire / Terminal Block
Neutral – Blue or Black Blue or N
Live – Brown or Red Brown or L
Reinstall the cover back onto the terminal box and ensure it is secure by clicking the cover into the tabs.
NOTE : THE INSTALLING ELECTRICIAN MUST ENSURE THE SUPPLY WIRE MAINTAINS DOUBLE INSULATION AFTER CONNECTING TO THE TERMINAL BLOCK.
Check and ensure all the quick connectors are connected and the wiring is neatly arranged
Install the luminaire onto the mounting bracket and secure by tightening the screws on the sides.
After the installation is complete, switch on the luminaire to test and enjoy your new lighting product.

Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning or making any adjustment to the luminaire.
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
Select a suitable location away from liquids and hazards.
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire shall be replaced. There are no serviceable parts, do not attempt to dismantle or open the product

Lucci-LEDlux-181045-Yuma-Round-Large-Flush-FIG-1

Troubleshooting

PROBLEM| POSSIBLE CAUSE| SUGGESTED SOLUTION

Does not work. (New installation)

|

Loose wiring or no power to the luminaire.

| Check your circuit breaker/safety switch box and

turn on the power to your circuit.

Contact the installing licensed electrician to check if

the luminaire has been installed correctly.

Does not work. (Existing installation)

|

No power to the luminaire.

| Check your circuit breaker/safety switch box and

turn on the power to your circuit.

Contact your nearest Beacon Lighting store.

Flickers when dimming.

(New installation)

|

Non-recommended dimmer used.

| Check the dimmer used. Ensure the dimmer used is on the list of recommended dimmers in this manual.
Some dimmers have a variable loading adjustment function. e.g. Lucci LEDlux SKU# 290998 dimmer.

This may not have been adjusted during

the installation of the dimmer.

|

The variable resistor needs to be adjusted to suit the luminaire load to reduce the flickering.

Flickers when dimming.

(Existing installation)

|

Dimmer position on low.

| Ensure the dimmer position is on the maximum setting before turning on the luminaire and adjust the

dimmer down to your desired light level.

Buzzing sound.

|