Uolfin A04266 Optimant Lighting Theia 3-Light Black Chandelier Instruction Manual

: June 3, 2024
: Uolfin

Table of Contents

Item Number: A04266
TOOLS REQUIRED (NOT INCLUDED)
Components
ACCESSORIES & QTY ENCLOSED:
ASSEMBLY & INSTALLATION INSTRUCTIONS:
Support & Service
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Uolfin A04266 Optimant Lighting Theia 3-Light Black Chandelier Instruction Manual

Item Number: A04266

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later
Before you start, NEVER attempt any work without shutting off the electricity until the work is
- Go to the main fuse, or circuit breaker, box in your home.
  Place the main power switch in the “ OFF ” position.
- Place the wall switch in the “ OFF ” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before
Make sure the voltage you are using is 120V. The maximum wattage is 40W per
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT :

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

| | | |
---|---|---|---|---
Ladder| Philips head.flat blade screwdriver| Electric tape| Pilers| Wire cutter/stripper

Components

product overview

PARTS TYPE & QTY INCLUDING:

C: Single bar (1)
D: Green ground screw (1)
E: Canopy (1)
F: Collar ring (1)
G: Collar loop (1)
H: Quick link (2)
I: Chain (1)
J : Screw (3)
K: Loop (1)
L: Loop assembly (1)
M: Threaded pipe (3)
N: Stem (1)
O: Socket cover (3)
P: Glass shade (3)
Q: Wire cage (3)
R: So: cket (3)
S: Arm (3)
T: Arms assembly (1)

ACCESSORIES & QTY ENCLOSED:

A: Wire connector (3)
B: Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Make preinstallation

Step A1 » Pass fixture wires through stem (N), and screw it onto arms assembly (T).
Step A2 » Position threaded pipes (M) on arms (S) in place, and secure threaded pipes (M) onto loop assembly (L) with screws (J).

ASSEMBLY & INSTALLATION
** Step B1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
Step B2 » Attach quick link (H) to chain (I) and loop (J) on the top of fixture loop assembly (K).
Step B3** » Carefully weave the fixture wires through chain (I) in and out of every other link and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.

Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “ OFF ” position.
Place the wall switch in the “ OFF ” position.
Make installation

Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).
NOTE: the side of single bar (C) marked “GND” must face out.
Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position. Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to the following note, you would know the proper position where collar loop (G) should be located
NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should be screwed enough threads (no less than 6 threads) on the preassembled threaded nipple for more secure hanging. If not, adjust collar loop (G) on single bar assembly (C) by screwing collar loop (G) in or out of single bar (C) until the secure length is achieved
Step C3 » Pass chain (I) through collar ring (F) and then through canopy (E).
Step C4: Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H). Pass the fixture wires through collar loop (G) to the top of the preassembled threaded nipple and gently pull to ensure the wires are not stressed
Step C5 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.
Step C6 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart

Connect wires according to the below chart

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
StepC7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G)

Step C8 »

1. Carefully place glass shades (P) on wire cages (Q), and secure them with socket covers (O).
2. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
**** To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.