Uolfin 4806468 3-Light Gold Bathroom Vanity Light with Clear Glass Shades Installation Guide

3-Light Gold Bathroom Vanity Light with Clear Glass Shades
Installation Guide
Item Number: 4806468

4806468 3-Light Gold Bathroom Vanity Light with Clear Glass Shades

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   » Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position.
   » Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING:
(C) Mounting plate (1)
(E) Green ground screw (1)
(F) Back plate (1)
(G) Stud (2)
(H) Socket (3)
(I) Iron frame (3)
(J) Glass shade (3)
(K) Socket ring (3)

ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   » Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position.

3. Make assembly
   » Place the wall switch in the “OFF” position.
   Step A1 » Unscrew studs (G) from back plate (F), then set them aside for later installation.
   Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
   Step A3 » Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the below chart
   Connect wires according to the below chartConnect Black or Red Supply Wire to:| Connect  White Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black withouttracer| Clear, Brown, Gold or Black with tracer
   Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

• Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (F) and mounting plate (C), then secure them with the previously removed studs (G).
Step A5 » 1) Remove socket rings (K) from sockets (H).
2) Carefully place glass shades (J) on iron frames (I).
3) Secure glass shades (J) with socket rings (K).
4) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

4. Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
uolfin@newdecorworld.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>