JBC SS 7300 Soldering Stand User Manual
- June 3, 2024
- JBC
Table of Contents
JBC SS 7300 Soldering Stand
Interdiction
To clean the tips, use the sponge included with the stand and check it is
slightly misted.
Only deionized water should be used in order to wet the sponge. If normal
water was to be used, it is very likely that the tip will become dirty due to
the salts dissolved within the water.
We appreciate the trust you have placed in JBC in purchasing one of our soldering irons. It is Manu – factored to the most strictest quality standards in order to give you the best possible service.
SPECIFICATIONS
Straight Type
50 S LD
- with Long Life tip Ref. 0502020
- Power: 70 W
- Maximum temperature: 460 °C
- Time to reach 325°C: 4,5 min
- Long Life Tip (LD) 50D: Ref. 0500405
- Soldering iron weight: 0,33 kg (0.72lb)
80 S LD
- with Long Life tip Ref. 0802020
- Power: 95 W
- Maximum temperature: 460 °C
- Time to reach 325°C: 6 min
- Long Life Tip (LD) 80D: Ref. 0800409
- Soldering iron weight: 0,24 kg (0.52lb)
Hammer Type
150 S LD
- with Long Life tip Ref. 0182020
- Power: 150 W
- Maximum temperature: 550 °C
- Time to reach 325°C: 7 min
- Long Life Tip (LD) 150D: Ref. 0180420
- Soldering iron weight: 0,55 kg (1.21lb)
325 S LD
- with Long Life tip Ref. 0352020
- Power: 300 W
- Maximum temperature: 550 °C
- Time to reach 325°C: 10 min
- Long Life Tip (LD) 325D: Ref. 0350170
- Soldering iron weight: 1,15 kg (2.53lb
The soldering irons with these references are to be connected to 230V UK, for other voltages please consult with us.
RECOMMENDATIONS FOR SOLDERING
For best results during soldering it is essential that:
- The tip is well tinned.
- Parts to be soldered are absolutely clean and if possible also pre-tinned.
TIP CLEANING
When the tip has become so oxidized as to make soldering difficult, proceed as follows:
- Unplug the soldering iron.
- Long-life tips: clean the area to be tinned, removing any oxide. For this purpose were commend our wire brush with which the stand SS 7300 Ref. 0187300 is equipped, or else a very fine file applied very gently so as not to damage the tip’s protective coating.
- Plug in the soldering iron and, before it reaches its working temperature, test it out by soldering using flux-core solder.
Never use the soldering iron without tip because it could cause SEVERE DAMAGE to the heating element.
LONG-LIFE TIPS
Features
- Copper basis
- Iron layer
- Nickel layer
- Chromium layer
- Pre-tinning
All these protection layers avoid that tin comes into contact with the copper basis and damages it which gives such tip a 10 to 20 times longer working live than the traditional tip while keeping its original shape without deformation by wear.
LONG LIFE TIP
| Dimensions mm| 
---|---|---
Sold.| Part N.| Tip|
Y / X
50 S
| 0500405| 50 D|
7,5×2
|
80 S
| 0800409| 80 D|
8,5×2
| 
150 S
| 0180420| 150 D|
16,5×5
| 
325 S
| 0350170| 325 D|
26,5×7,5
| 
Dimensions
WARRANTY ENGLISH
The JBC 2 years warranty, guarantees this equipment against all manufacturing
defects, covering the replace – mint of defective parts and all necessary
labor.
Warranty does not cover product wear due to use or mist-use.
In order for the warranty to be valid, equipment must be returned to the
dealer where it was purchased
This product should not be thrown in the garbage.
RoHS compliant.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>