STOVES EMIIAN381 Cooker Hood User Manual
- June 3, 2024
- STOVES
Table of Contents
STOVES EMIIAN381 Cooker Hood
Introduction
Thank you for buying this high quality hood from Stoves.
Our policy is one of constant development and improvement. Strict accuracy of
illustrations and specifications is not guaranteed. Modification to design and
materials may be necessary subsequent to publication. Before using the
appliance for the first time, remove all packaging and protective polythene
film. This appliance has been designed for use as an exhausting (air
evacuation to the outside) or filtering (indoor air re-cycling) hood. Note:
This appliance does not come supplied with a ducting kit, or carbon filters.
Details for ordering these parts are at the back of the handbook. Because of
the complexity and weight of the appliance, it is recommended that the
installation be carried out by specialist personnel. The manufacturer declines
all responsibility for damage caused by improper or installation. Please read
this handbook carefully and keep it for future reference.
Your first year Guarantee
To fulfil the conditions of your guarantee, this appliance must be correctly
installed and operated in accordance with these instructions and only be used
for normal domestic purposes. Please refer to your guarantee card for further
details. Please note that the guarantee and Service availability only apply to
the UK and Republic of Ireland.
SAFETY PRECAUTION
Take care when the cooker hood is operating simultaneously with an open
fireplace or burner that depends on the air in the environment. The cooker
hood removes the air from the environment which a burner or fireplace needs
for combustion.
The negative pressure in the environment must not exceed 4Pa (4×10-5 bar).
Provide adequate ventilation in the environment for a safe operation of the
cooker hood. Follow the local laws applicable for external air evacuation.
Before connecting the model to the electricity network review the data plate
(positioned inside the appliance) to confirm that the voltage and power
correspond to the network and the socket is suitable. If in doubt ask a
qualified electrician.
If the power supply cable is damaged it must be replaced. This can be obtained
direct from the manufacturer. This device must be connected to the supply
network through either a plug fused 3A or hardwired to a 2 phase spur
protected by 3A fuse.
Warning!
In certain circumstances electrical appliances may be a danger hazard.
- A) Do not check the status of the filters while the cooker hood is operating.
- B) Do not touch bulbs or adjacent areas during or straight after prolonged use of the lighting installation.
- C) Flambè cooking is prohibited underneath the cooker hood.
- D) Avoid free flame as it is damaging for the filters and a fire hazard.
- E) Do not leave food frying unattended as the overheated oil may become a fire hazard.
- F) Disconnect the electrical connection prior to any maintenance.
- G) This appliance is not intended for use by young children or infirm persons without supervision.
- H) Young children should be supervised to ensure they do not play with the appliance.
- I) There shall be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels other than electric.
- L) There is a risk of fire if cleaning is not carried out in accordance with the instructions.
This appliance conforms to the European Directive EC/2002/96, Waste Electrical
and Electronic Equipment (WEEE). The symbol on the product or on the
accompanying paperwork indicates that the appliance should not be treated as
domestic waste, but should be delivered to a suitable electric and electronic
appliance recycling collection point.
Follow local guidelines when disposing of waste.
For more information on the treatment, re-use and recycling of this product,
please contact your local authority, domestic waste collection service or the
retailor where the appliance was purchased.
INSTALLATION INSTRUCTIONS
-
Assembly and electrical connections must be carried out by specialised personnel.
-
Wear protective gloves before proceeding with the installation.
-
Electric Connection:
- The appliance has been manufactured as a class II, therefore no earth cable is necessary. The power point must be easily accessible after the installation of the appliance. If the appliance is equipped with power cord without plug, a suitably dimensioned omnipolar switch with 3 mm minimum opening between contacts must be fitted between the appliance and the electricity supply in compliance with the load and current regulations.
- The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral.
-
If the hob is electric, gas, or induction, the minimum distance between the same and the lower part of the hood must be at least 65 cm. If a connection tube composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source. Before proceeding with the assembly operations, remove the anti-grease filter(s) (Fig.1) so that the unit is easier to handle.
- In the case of assembly of the appliance in the suction version prepare the hole for evacuation of the air.
-
We recommend the use of an air exhaust tube which has the same diameter as the air exhaust outlet hole. If a pipe with a smaller diameter is used, the efficiency of the product may be reduced and its operation may become noisier.
-
If your appliance has been designed for use in habitations supplied with a centralised suction device perform the following operations:
- The switch controls opening and closure of a valve using a thermo electrical device. By placing the switch in the ON position, after a minute, the valve opens rotating 90° allowing suction of the stale air. By placing the switch in the OFF position, the valve closes after 100 seconds.
-
Fixing to the wall:
Drill the holes A respecting the distances indicated (Fig.2). Fix the appliance to the wall and align it in horizontal position to the wall units. When the appliance has been adjusted, definitely fix the hood using the screws A (Fig.3). For the various installations use screws and screw anchors suited to the type of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with the product, check that they are suitable for the type of wall on which the hood is to be fixed. -
Fixing the decorative telescopic flue:
Arrange the electrical power supply within the dimensions of the decorative flue. If your appliance is to be installed in the ducting version or in the version with external motor, prepare the air exhaust opening. Adjust the width of the support bracket of the upper flue (Fig.4). Then fix it to the ceiling using the screws A (Fig.4) in such a way that it is in line with your hood and respecting the distance from the ceiling indicated in Fig.2. Connect the flange C to the air exhaust hole using a connection pipe (Fig.5). Insert the upper flue into the lower flue and rest above the frame. Extract the upper flue up to the bracket and fix it with the screws B (Fig.4). To transform the hood from a ducting version into a filtering version, ask your dealer for the charcoal filters and follow the installation instructions. -
Filtering version:
Install the hood and the two flues as described in the paragraph for installation of the hood in ducting version. To assemble the filtering flue refer to the instructions contained in the kit. If the kit is not provided, order it from your dealer as accessory. The filters must be applied to the suction unit positioned inside the hood. They must be centred by turning them 90 degrees until the stop catch is tripped (Fig.6).
USING THE HOOD
Controls
Lamp
- Depress to turn on/off light
Speed- select speed to suit cooking conditions.
- Low- Light frying/boiling. Depress this button to enter into low speed and again to turn off motor.
- Medium – Frying/wok cooking/heavy boiling. Depress this button to enter into medium speed and again to turn off motor.
- High – Grilling, intensive frying and wok cooking. Depress this button to enter into high speed and again to turn off motor.
- Booster – Depress this button to enter into highest speed and again to turn off motor.
Booster function
This hood also has a booster function. To activate the booster, press button B
while the hood is in use and it will increase speed for 8 minutes, before
slowing down again.
We recommend that you switch on the hood for a few minutes before you start
cooking, and then leave it running for approximately 8 minutes afterwards to
ensure that all odours are extracted.
The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
WARNING – Accessible parts may become hot when used with cooking
appliances. To illuminate the cooking area underneath the hood, push the light
control button in to the “on” position. To switch off, press again to return
to the “off” position.
To operate the hood, press the button for the required speed – select: 1 low,
2 medium, or 3 high speed. The neon indicator light will light up to show when
the fan is operating. To switch off, press the “off” button.
CARE & CLEANING
Before cleaning or maintenance, switch off the electricity supply.
Replacing the LED Lights
If the appliance version is with LED lamps, the intervention of a specialised
technician is necessary to replace them
Outer Casing
-
All external parts of the outer casing can be safely cleaned with a clean cloth wrung out in hot soapy water. Do not use caustic pastes, abrasive cleaning powders, wire wool, hard implements, or any products containing chlorides as they will damage the surfaces.
-
Stubborn marks can be removed using a stainless steel cleaner. We recommend that you clean the whole of the stainless steel area to maintain a uniform finish.
Sharp objects can mark the surface of stainless steel, but marks will become less noticeable with time. -
To maintain the finish of the stainless steel, or to remove any greasy marks, wipe the stainless steel surface sparingly with a minimum amount of Baby Oil and kitchen paper.
-
Do not use cooking oils, as these may contain salt, which can damage the stainless steel surface.
-
Before cleaning or maintenance, switch off the electricity supply.
-
To avoid any fire risk, the following cleaning instructions must be followed:
Grease Filters
The grease filters absorb grease and dust from cooking fumes, which would
otherwise damage the inside of the hood. The grease filters should be removed
and cleaned regularly – with normal use, this should be every 2 months. To
clean use warm soapy water, or wash in a dishwasher. The grease filters may
slightly change colour following washing, however this does not affect their
performance.
Important: Frequent washing is essential to prevent a build-up of grease
in the filters which could become a fire hazard.
- Remove the filters from the hood.
- Carefully wash the grease filters in hot soapy water and dry with a clean towel.
- Refit the clean filters.
Carbon Filters (models installed for use with the re-circulation method
only)
The carbon filters absorb cooking odours and need renewing after about 6
months of normal use. Replacement carbon filters can be obtained from our
Customer Care (details at the rear of the handbook). Saturation of the
activated charcoal in the filter will depend on how often the hood is used,
the type of kitchen and the regularity of cleaning the grease filter. The
carbon filters cannot be washed – renew every 6 months.
TECHNICAL DATA
-
Electricity Supply 220 – 240V ~ 50Hz
-
Classification class I
-
Noise Level (External Venting) Flat Hood
- Booster 72 dBA
- Position 3 6dBA 5
- Position 1 5dBA
-
Chimney Hood:
- Booster 72 dBA
- Position 3 65 dBA
- Position 1 52 dBA
-
Light Lulbs 2 x 1.5W LED
-
Motor Rating 250W
-
Grease Filters 3 Off – Aluminium panel
Note: After cleaning, grease filters may lose their colour slightly – this does not affect their performance. -
Carbon Filters 2 Off – Available as Spares
-
Extraction Rate (External)
Flat Hood- Booster 805.8 m3/H
- Position 3 605.7 m3/H
- Position 1 280.0 m3/H
-
Chimney Hood
- Booster 805.8 m3/H
- Position 3 605.7 m3/H
- Position 1 280.0 m3/H
Information for domestic range hoods
Symbol | Value | Unit | |
---|---|---|---|
Model identification | |||
Annual Energy Consumption | AEChood | 57 | kWh/a |
Time increase factor | f | 0.9 | |
Fluid Dynamic Efficiency | FDEhood | 31.5 | |
Energy Efficiency Index | EEIhood | 52.7 | |
Measured air flow rate at best efficiency point | QBEP | 404.1 | m3 /h |
Measured air pressure at best efficiency point | PBEP | 459 | Pa |
Maximum air flow | Qmax | 605.7 | m3/h |
Measured electric power input at best effi ciency point | WBEP | 163.4 | W |
Nominal power of the lighting system | WL | 3 | W |
Average illumination of the lighting system on the cooking surface | Emiddle | ||
110 | lux | ||
Measured power consumption in standby mode | Ps | 0.29 | W |
Measured power consumption off mode | Po | N/A | W |
Sound power level | LWA | 67 | dB |
STOVES CUSTOMER CARE
Please keep this handbook in a safe place.
Please fill in the model number and serial number in the spaces provided below
as they will assist us should you need to call. 0844 815 3740
When you dial this number you will hear a recorded message and be given a
number of options. This indicates that your call has been accepted and is
being held in a queue. Calls are answered in strict rotation as our Customer
Care Representatives become available.
Enter appliance numbers here for future reference:
These numbers can be found on your appliances. Outside the UK and Northern Ireland, refer to your local supplier.
Stoney Lane, Prescot, Merseyside, L35 2XW
Contact details
Country | Contact Address | Contact details |
---|---|---|
France | Glen Dimplex France ZI petite Montagne Sud |
12 rue des Cévennes – Lisses 91017 EVRY cedex
FRANCE
| Service Number: 01 69 11 11 85
Tel: 00 33 (0)1 69 11 11 91
direction@glendimplex-france.fr
Holland/ Belgium| Glen Dimplex Benelux B.V. Nederland/Le Pays Bas Saturnus 8
8448 CC Heerenveen
Tel: +31 (0) 513-656500
Fax: +31 (0) 513-656501
www.stoves.nl België/Belgique Burgemeester Maenhautstraat 64
9820 Merelbeke
Tel: +32 (0)92100210
Fax: +32 (0)92100212
| Productregistratie/ Registration de produit www.gdbservice.com Serviceaanvraag/ Demande de service
www.stoves.nl / www.stoves.be zie banner ‘service’ homepagina
voir la banniere ‘service’ sur notre page d’accueil
Germany/ Austria| ELESCO EUROPA GmbH Karl-Wiechert-Allee 74a D-30625 Hannover| Teleofon: +49-(0)511-5151 3360
Fax: +49 (0)511 5343 0910
Poland| OPTIDATA Sp. z o. o., ul. Wielicka 50/5, 30-552 Kraków| +48 12 383 39 30
www.kuchniestoves.pl service.stoves@optidata.pl
Sweden| Lindström & Sondén AB Havsbadsvägen 1
26263 Ängelholm
| Tele: 010-1011656
Email: info@lsbolagen.se
Republic of Ireland| Glen Dimplex Ireland, Airport Road, Cloghran, Co. Dublin|
Service Telephone No.’ (01) 8428222 Service and Spare Parts.
serviceireland@glendimplex.com
Other| Glen Dimplex Home Appliances, Stoney
Lane, Prescot, Merseyside, L35 2XW
| Tel: 0844 815 3740
References
- Europa.com is For Sale | BrandBucket
- France.fr : Explore France and its wonders - Explore France
- Home | Glen Dimplex Ireland
- Homepage | Glen Dimplex
- Homepage | Glen Dimplex
- Stoves fornuizen – Unieke A-kwaliteit producten | Stoves
- Stoves fornuizen – Unieke A-kwaliteit producten | Stoves
- Stoves fornuizen – Unieke A-kwaliteit producten | Stoves
- Stoves fornuizen – Unieke A-kwaliteit producten | Stoves
- Vittoria5Sterne: W&B Dr. Becker Appliances; Exklusive Haushaltsgeräte für die anspruchsvolle Küche
- Vittoria5Sterne: W&B Dr. Becker Appliances; Exklusive Haushaltsgeräte für die anspruchsvolle Küche
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>