HENLEY STOVES 465 Double Sided Stoves Instruction Manual
- June 2, 2024
- HENLEY STOVES
Table of Contents
465 Double Sided Stoves
“`html
Specifications:
- Model: Hazelwood / Dalewood DS
- Confirms to: EN13240
- Dimensions: H: 530mm W:465mm D:582mm
- Weight: 105KG
- Flue Size: 125mm
- ERP Rating: A
- Fuel: Wood
- Heat Output: 6.5kW
- Efficiency: 75.8%
- Emissions CO at 13% O2: 0.12
- Flue Gas Mass Flow: 6.6g/s
- Mean Flue Gas Temp.: 298K
Product Usage Instructions:
1. Installation Instructions:
To ensure safe and proper installation of your Henley Stove, it
must be done by a qualified HETAS/METAC installer. Refer to the
installation section in the manual for detailed instructions on
fitting the stove.
2. Operating Instructions:
Once installed, follow these steps to operate your stove:
-
Prepare the fire bed with suitable wood fuel.
-
Open the air controls and light the fire following the
instructions provided. -
Adjust the air controls to regulate the heat output.
-
Maintain proper ventilation to ensure efficient burning.
3. Maintenance:
Regular maintenance is essential for the longevity of your
stove. Follow these maintenance guidelines:
-
Clean the baffle plate, hearth, chimney, and ash-pan
regularly. -
Check and replace fire rope and baffle plate when
necessary. -
Schedule annual service and chimney sweeping.
Frequently Asked Questions (FAQ):
Q: Can I burn other fuels besides wood in the stove?
A: No, this stove is suitable for wood burning only. Burning
other fuels can damage the stove and pose safety risks.
Q: How often should I clean the chimney?
A: The chimney should be swept regularly, at least once a year,
to remove creosote buildup and ensure proper ventilation.
Q: What should I do if I experience smoke spillage from the
stove?
A: Check the flue integrity, ensure proper ventilation, and
contact a qualified technician if the issue persists.
“`
Hazelwood / Dalewood
Double Sided Stoves
Installation & Operating Instructions
IMPORTANT!
THIS APPLIANCE IS SUITABLE FOR WOOD BURNING ONLY
Our wood burning stoves must be fitted by a HETAS/METAC Qualified Installer.
The Heating Specialists “Every Home Deserves A Henley”
1
Congratulations on the purchase of your New Henley Stove! With the proper care
& attention your Henley stove will give you a lifetime of heat & comfort.
This manual contains instructions on how to install and maintain your Henley
Stove. For both your comfort & safety please take the time to read
instructions carefully.
HENLEY STOVES WARRANTY
How to register your new stove: Henley Stoves does not accept warranty
submissions through post/email. Please register your warranty at
https://henleystoves.com/warranty/
See page 22 of this Manual for full details on Warranty Terms & Conditions.
Index
1. Technical Information 2. Stove Commissioning Checklist 3. Installation Instructions
3 12. Shutting Down Stove
4 13. Maintenance
5
Baffle Plate
14 14 14
Hearth
6
Chimney Sweeping
14
Ventilation
7
Removing The Ash-pan
15
Chimney
7-8
Replacing Fire Rope
15
4. Flue Positions
8
Replacing Baffle Plate
16
Height Over Adjacent Building
9
Replacing Stove Door Glass
16
Height Over Roof
9
Removing The Fuel Retainer
16
Height Over Openings
5. Flue Options Flue Options – Top/Rear
Flue Options – Diagram
6. Non-Combustible Materials 7. External Air 8. The Clean Air Act 1993 9.
Combustible Materials
9 14. Air Controls
10 15. Useful Information
10 16. Stove Finish (Paint)
10 17. Chimney Fire & Over-firing
11 18. Carbon Monoxide Alarm
11 19. Spare Parts
12 20. FAQ’s
12
Annual Service
17 17 18 18 18 19 20 21
10. Recommended Fuels
12
Seasonal Use
21
11. Lighting The Stove
13
Ventilation
21
Re-fueling
13 21. Terms & Conditions
22
Refueling On To A Low Fire Bed
14
Fuel overloading
14
Operation With Door Left Open
14
Dampers Left Open
14
2
Hazelwood Double Side
465
500
232
530
291
582
56 210
100 420
Dalewood Double Side
465
500
232
530
291
582
56 210
100 420
Specifications
Hazelwood / Dalewood DS
CONFIRMS TO
EN13240
DIMENSIONS
H: 530mm W:465mm D:582mm
WEIGHT
105KG
FLUE SIZE
125mm
ERP RATING
A
FUEL
WOOD
HEAT OUTPUT
6.5kW
EFFICIENCY EMMISSIONS CO AT 13% O2 FLUE GAS MASS FLOW – g/s
75.8% 0.12 6.6
MEAN FLUE GAS TEMP. K#
298
3
Stove Commissioning Checklist
Please complete the form below as it will be of great assistance in the highly
unlikely event that there is a problem with the stove or a warranty claim
needs to be made. Please contact the person who installed the stove or the
dealer where it was purchased from if there is a problem.
Dealer Appliance Was Purchased From
Name:
Address:
Phone:
Essential Information – MUST BE COMPLETED
Date installed: Model Description: Serial number:
Installation Engineer
Company name:
Address:
Phone:
HETAS Approved (Please tick relevant box):
Yes
No If Yes, please include certificate of compliance.
Commissioning Checks (to be completed and signed)
Stove correctly flued according to building regulations: Flue swept and integrity of flue verified: Smoke test completed on installed stove: Spillage test completed: Use of appliance and operation of controls explained to end- user: Check that specified clearance to combustibles has been adhered to: Instruction manual handed to end-user:
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Signature:
Print name:
4
Installation Instructions
Installation Before installation and/or use of this appliance please read
these instructions carefully to ensure that all requirements are fully
understood. The appliance must be fitted by a registered installer*, or
approved by your local building control officer.
Regulations Please refer to the current issue of British Standard BS 8303,
Code of Practice for Installation of domestic heating appliances burning solid
fuel, Building Regulations, Local Authority Bylaws and other specifications or
regulations including Ireland, UK or EU standards referred to as they affect
the installation of the stove. Building regulations available on
www.environ.ie & www.planningportal.gov.uk.
Domestic Heating Only use for domestic heating in accordance with these
operating instructions.
Fuel Only approved fuels must be burned. Do not use liquid fuels or as an
incinerator.
Fireguard Appliance surfaces become very hot when in use. A fireguard
conforming to BS 8423:2010 should be used in the presence of children, the
elderly or infirm. Please note, this appliance should be used with the fire
door closed at all times except when fueling, cleaning ash or initial
lighting.
Combustible Materials Do not place photographs, TV’s, paintings, porcelain or
other combustible items on the wall or near the appliance. Exposure to hot
temperatures will cause damage. Do not place furniture, or other items such as
drying clothing, closer than 1 metre from the front of this appliance. Do not
use aerosol sprays or any other flammable materials near the appliance under
fire.
Asbestos This stove contains no asbestos. If there is a possibility of
disturbing asbestos in the course of installation then please seek specialist
guidance & use appropriate protective equipment.
Fire Cement Some types of fire cement are caustic and should not be allowed to
come into contact with the skin. In case of skin contact, wash immediately
with plenty of water.
Extractor Fan It is possible to install this appliance in a kitchen or open
plan room which uses an extractor fan. Adequate provisions must be made, as
the extractor will draw air from the room. A draught test needs to be carried
out on the appliance with the extractor fan running on full power. Based on
results from the draught test, extra ventilation should be added where
necessary.
Ventilation: Do not obstruct inside or outside ventilation required for the
safe use of this appliance.
Alterations Do not make unauthorized changes to the appliance.
Chimney The chimney must be swept at least once a year.
Flue System Do not connect, or share, the same flue or chimney system with
another appliance.
Serial Number The serial number is required when ordering spare parts or
making warranty claims. It is found on the appliance data plate.
Manual Handling Before continuing any further with the installation of this
appliance please read the following guide to manual handling. · Always obtain
assistance when lifting · When lifting always keep your back straight · Avoid
twisting at the waist. It is better to
reposition your feet. · Avoid upper body/top heavy bending. Do not
lean forwards or sideways · Always grip with the palms of your hands do not
use your fingertips for support, use gloves for a better grip · Always keep
the stove close to the body as this will minimize the cantilever action.
5
Hearth
Hearths should be constructed from suitably robust materials & to appropriate
dimensions. (fig.1)
A way of making provision would be to adopt the guidelines outlined below & to
provide a hearth appropriate to the temperatures that the appliance can create
around it.
The hearth should be able to accommodate the weight of the appliance & it’s
chimney if the chimney is not independently supported. Consult a structural
engineer for advice before proceeding.
If there is no existing fireplace or chimney it is possible to construct a
suitable non-combustible housing and hearth setting. The flue must be
installed in accordance with all local and national regulations and current
rules in force. Check if adding a new chimney to your property requires
planning permission.
The Stove should be installed on: A: Hearths made of non-combustible board /
sheet material or tiles at least 12mm thick (fig.3), if the appliance is not
to stand in an appliance recess and has been tested to an applicable appliance
standard to verify that it cannot cause the temperature of the upper surface
of the hearth to exceed 100°C; or
B. Constructional hearths in accordance with the guidelines outlined. (fig.2)
Constructional Hearths should have dimensions as outlined in figure 1 above.
They should be made of solid, non-combustible such as concrete or masonry, at
least 125mm thick, including the thickness of any noncombustible floor and/or
decorative surface.
fig.2 Non Combustible Hearth surrounding Solid Fuel Appliance
fig.1 Constructional Hearth Dimensions for Solid Fuel Appliances & Open Fires
6
fig.3. Ways of Providing Hearths
Ventilation
This appliance requires a constant supply of air to maintain proper combustion
and effective flue performance.
An inadequate air supply can result in poor combustion and smoke entering the
room which is potentially dangerous.
This supply of air can come from either: · The natural leakage of air into the
room in which the product is fitted. · Purpose provided ventilation.
The amount of air required must comply with local building regulations and the
rules in force. If spillage is detected during commissioning then there may be
insufficient natural ventilation and an additional air supply will be
necessary.
Many older buildings are sufficiently ventilated by natural leakage of air to
provide suitable air supply for an appliance of 5kW output or less. Any air
vents should be positioned so that they are not liable to blockage.
Chimney
Please refer to the current issues of British Standards BS EN 15287-1:2007
design,installation and commissioning of chimneys before commencing
installation
The chimney draw is critical on any installation and should be checked to
ensure that it matches what is specified. If the draw is higher than
recommended, we advise that provision must be made to correct the overdraw.
The draw can vary in different weather conditions and the customer should be
made aware of this. Failure to correct an over-drawing flue will invalidate
the warranty, and may damage the appliance.
Please remember that chimney draught is dependent on four main factors. · Flue
gas temperature · Flue height · Flue size · Flue terminal
The flue or chimney system must be in good condition. It must be inspected by
a HETAS / MECTACQualified Installer and passed for use with the appliance
before installation. Products of combustion entering the room can cause
serious health risks.
The following must be checked: · The construction of the masonry chimneys,
flue block chimneys & connecting flue pipe system must meet requirements of
the Building Regulations.
We recommend a flexible flue liner system certified for use with solid fuel
systems be used to improve stove performance. The flue liner must be removed
when an appliance is replaced, unless proven to be recently installed and in
good condition. If it is necessary to fit a register plate it must conform to
the Building Regulations.
·The minimum height of the flue or chimney must be 4.5m from the hearth to the
top of the flue, with no horizontal sections & a maximum of 4 bends. Bends
must have angles of less than 45 degrees from the vertical.
Ensure the connecting flue pipe is kept a suitable distance from any
combustible material and does not form part of the supporting structure of the
building.
Make provision to remove the appliance without the need to dismantle the
chimney.
Any existing flue must be confirmed as suitable for the new intended use as
defined in the Building Regulations.
The flue or chimney systems must be inspected and swept to confirm the system
is structurally sound and free from obstructions.
If the chimney is believed to have previously served an open fire it must be
swept a second time within a month of regular use after installation to clear
any soot falls that may have occurred due to difference in combustion levels.
The flue exit from the building must comply with local building control rules.
Do not connect or share the flue or chimney system with another heating
appliance.
Do not connect to systems containing large voids or spaces over 230mm square.
7
Chimney
Suitable access must be provided to enable the collection and removal of
debris.
The flue must be swept and inspected when the appliance is installed.
The flue draught must be checked with all windows and doors closed and any
extraction fans in this, or adjoining rooms, running at maximum speed (see
next section for additional ventilation requirements).
· Max. draught = 2.0mm Wg, · Min. draught = 1.0mm Wg
Flue Positions
These positionsTahreesdeepfionseitdiobnysDaorecudmefiennetdJ
obfytDheocBuumildeinntgJ RoefgthuelaBtiounilds.ing Regulations.
A D
B C
Adjacent Building
WARNING
Under no circumstances should this appliance be connected to a shared flue
system, that serves
any other heating appliance.
Seek specialist advice if installing in a dwelling with a thatched roof
Terminal Flue
Horizontal Measurement
Vertical Measurement
150mm Max
Insulation
Adjacent Building
The datum for vertical measurement is the point of discharge of
thedflisucehafrogme oefitherfltuhee fprominteoitfhdeirsxthcheaprogeint of
disxcharge ofn the flue or 1o5f0nmthme
aflbuoevoerin15su0lmatmiona,bwohveicihnesvuelar tiison, whichever is
the lower.
Point where the flue passes through weather surface (Note 1 & 2) Clearances to the flue outlet
A At or within 600mm of the ridge
At least 600mm above ridge
B Elsewhere on the roof (whether pitched or flat)
At least 2300mm horizontally from the nearest point on the weather surface (a) at least 100mm above the highest point of interaction of the chimney and weather surface; or (b) at least as high as the ridge
C Below (on a pitched roof) or within 2300mm horizontally to openable rooflight, dormer window, or other opening (Note 3)
At least 1000mm above the top as the ridge
D Within 2300mm of an adjoining or adjacent building, not beyond the At least 600mm above any part of the adjacent of the
boundary (Note 3)
building wall
Note: 1. The weather surface is the building external, such as it’s roof tiles or external walls. 2. A flat roof has a pitch less the 10º 3. The clearance given for A or B, as appropriate, will also apply. 4. A vertical flue fixed to an outside wall should be treated as equivalent to an inside flue emerging at the nearest edge of the roof
8
Height Over Adjacent Building
The Outlet of a chimney or flue in relation to an adjacent building should be
as seen above
Height Over Roof
Outlet of a chimney or a flue to be not less that 1m above the highest point
of contact of chimney and roof. Where the roof has a pitch of more than 10º on
both sides and the outlet is at the ridge or within 600mm of it, the height of
the chimney or flue pipe may be reduced to 600mm.
Height Over Openings
The outlet of a chimney or flue pipe should also be not less than 1m above the
top of any opening skylight, opening window or wall ventilator within 2.3m
9
Flue Options
Each installation is unique to the property so it is not possible to give
details to suit every setting.
The installation must comply with Building Regulations and be made using best
practice construction methods.
Many fireplace openings have a supporting lintel. Do not remove without
supporting the remaining structure of the building.
Do not support the structure with the appliance or the flue system. Take care
when installing the appliance. Careless handling and use of tools can damage
the finish and/or area.
Choose top or rear flue exit and fit flue collar to suit installation. Seal
with fire cement.
WARNING
IF NOT using External Air Supply Ensure External flue on the underneath of
Stove covered
WE RECOMMEND
Flexi-Liner is Used for Maximum Efficiency
Flue Options – Top
Flue Setup – Diagrams
Flue conection
10
Non Combustible Reducer Plate (Minimum 1.5mm Thick Steel)
Distances to Non Combustibles
All stoves will require adequate distance between them & any noncombustible material to allow for both Installation & servicing, as well room for convection in order for the stove to operate correctly.
Use Diagram for Reference with Distances Outlined Below :
(A). = Dist. to non combustible wall (B). = Min. thickness of non-combustible
wall
Recommended safe distances to non-combustible materials should be 50mm to Rear
& 50mm to Sides.
Please Note: If the non combustible surface is less than 200mm thick,
additional clearances to these surfaces may be required.
· Where (A) distance = 50mm
(B) minimum thickness should be 200mm.
· Where (A) distance = 51mm to 300mm
(B) minimum thickness should be 75mm.
· Where (A) distance = over 300mm no requirement for (B) thickness
External Air
The external air supply allows the stove to be installed in a room that may
otherwise be sealed to an extent that would prohibit the correct and safe
burning of a wood stove.This would also apply to new builds in general which
are sealed to a very high level to meet various energy efficiency targets.
The air duct is fitted onto the stove around the air inlet control and is fed
from the supply tube on the rear face of the duct assembly. The flexible
piping should be taken directly to an external wall, avoiding sharp bens of
excessive direction changes.
This piping should be terminated at the wall and be fitted with a suitable
grill to prevent blockages by leaves and other debris.
11
The Clean Air Act 1993 & Smoke Control Areas
Under the Clean Air Act local authorities may declare the whole or part of the
district of the authority to be a smoke control area.
It is an offence to emit smoke from a chimney of a building, from a furnace or
from any fixed boiler if located in a designated smoke control area.
It is also an offence to acquire an “unauthorized fuel” for use within a smoke
control area unless it is used in an “exempt” appliance (“exempted” from the
controls which generally apply in the smoke control area).
In England appliances are exempted by publication on a list by the Secretary
of State in accordance with changes made to sections 20 and 21 of the Clean
Air Act 1993 by section 15 of the Deregulation Act 2015.
Similarly in Scotland appliances are exempted by publication on a list by
Scottish Ministers under section 50 of the Regulatory Reform (Scotland) Act
2014.
In Northern Ireland appliances are exempted by publication on a list by the
Department of Agriculture, Environment and Rural Affairs under Section 16 of
the Environmental Better regulation Act (Northern Ireland) 2016.
In Wales appliances are exempted by regulations made by Welsh Ministers.
Further information on the requirements of the Clean Air Act can be found
here: https://www.gov.uk/smoke-control-area-rules
Your local authority is responsible for implementing the Clean Air Act 1993
including designation and supervision of smoke control areas and you can
contact them for details of Clean Air Act requirements.
Combustible Materials
Safe distances to combustible materials for the Hazelwood / Dalewood DS should
be a minimum of 40cm to the Sides and 120cm to the Front.
Adjacent walls must be of suitable non combustible construction, preferably
brickwork.
In large fireplaces take care that any supporting beam is protected by a 13mm
(0.5″) thick sheet of Masterboard / Supalux spaced 13mm (0.5″) off the surface
with strips of non-combustible material.
Make sure that there is a gap between an uninsulated flue system and any
combustible material. This gap must be at least 3x the outside diameter of the
flue pipe, or 1.5x the flue diameter to non-combustible surfaces.
This gap must be at least 3x the outside diameter of the flue pipe, or 1.5x
the flue diameter to noncombustible surfaces.
Recommended Fuels
Wood logs – Burn only seasoned timber with a moisture content of less than
20%. To ensure this allow cut wood to dry for 12 to 18 months.
Poor quality timber causes low combustion efficiency, produces harmful
condensation, reduces effectiveness of the airwash and life of the appliance.
Wood length max 200mm, and 100mm in diameter.
12
Lighting the Stove
We recommend that you have two or three small fires before you operate your
stove to its maximum heat output.
This is to allow the paint to cure in steadily and to give a long service life
of the paint finish. During this curing in process you may notice an
unpleasant smell whilst the finishes finally cure. It is non-toxic, but for
your comfort we would suggest that during this period you leave all doors and
windows open.
First, open the primary and secondary air wash control fully. Load the firebox
with plenty of starting fuel, i.e. paper, dry sticks and/or firelighters.
Light the fire at the base leaving the primary and secondary air control fully
open. Leave the door slightly ajar for 10 minutes to enhance initial starting
and reduce smoke emission DO NOT leave the stove unattended if the door is
left ajar.
Allow the fuel to reach a steady glow and build the fire up gradually by
adding a few small sticks or well split logs at a time. Once you have a good
fire bed established across the grate, further fuel can be added step by step
as required.
Don’t be tempted to overload the fire bed with fuel all at once or close down
the air controls too much until the fire is really well established for some
time.
Once the ignition period is well under way close the primary air and gradually
reduce the secondary air wash control opening to establish the burning
intensity you require (usually open 25% approx.).
Refueling the Stove
When burning wood, the fire will die down as the fuel is consumed. When the
flames disappear and the remainder is breaking down into glowing embers it is
an appropriate time to consider refuelling.
Note: If the flames disappear and there are still lumps of solid wood left
this indicates excessive moisture in the wood or insufficient air supply/ flue
draught.
Note: To eliminate unwanted smoke emission, after loading new logs on to the
fire, open the air wash control up fully for 1-2 minutes to boost the fire and
get flames issuing from the top of the fuel as soon as possible. When flames
are well established, reduce the air wash to the running setting required.
Burning without flames above the fuel will create unnecessary smoke.
DO NOT load fuel above the tertiary air inlet holes at the back of the
firebox.
Loading 1 to 2 medium sized logs will produce a good output with reasonable
burn time, generally small logs will burn up quicker producing a high output
for a short time and a large log will take longer to burn and produce less
output over a given time.
This appliance is approved for intermittent operation on wood (0.75 to 1.5
hour burn cycles) although much longer burn times can be achieved by fully
loading the firebox, getting the fuel burning well and then shutting the air
controls down.
The fire will then often need reviving by first deashing and then using small
pieces of wood and plenty of air to get flames issuing from the wood again.
WARNING
HHENLEY RECOMMENDS THAT WOOD LOSS BE PLACED VERTICALLY IN THE STOVE FOR BEST
FLAME & FUEL CONSUMPTION RESULTS
13
When refueling the appliance it was necessary to leave the door ajar for a
period of 1 – 2 minutes in order to sustain flames on
the newly charged fuel load.
Directly after refueling it was necessary to operate with the secondary air
fully open for a period 3 to 5 minutes before closing to the
desired setting
Refueling on to a low fire-bed
If there is insufficient burning material in the fire-bed to light a new fuel
charge, excessive smoke emission can occur.
Refueling must be carried out onto a sufficient quantity of glowing embers and
ash that the new fuel charge will ignite in a reasonable period.
If there are too few embers in the fire bed, add suitable kindling to prevent
excessive smoke
Fuel Overloading
The maximum amount of fuel specified in this manual should not be exceeded,
overloading can cause excess smoke.
Operation with Door Left Open
Operation with the door open can cause excess smoke. The appliance must not be
operated with the appliance door left open.
Dampers Left Open
Operation with the air controls or dampers open can cause excess smoke.
The appliance must not be operated with air controls or dampers door left open
except as directed in the instructions.
Shutting Down Stove
The stove will normally shut down by itself as the fuel is consumed.
In order to shut down the stove for other reasons, close the primary air
controls (if open), then close the secondary air control.
If the controls are left in this position, the fire will eventually burn out.
If you want to revive the fire open the secondary air controls fully.
The stove will remain very hot for a considerable time after the fire has died
down or been extinguished. Petroleum coal fuels or household waste
must not be burnt in this appliance
Maintenance: Baffle Plate
Inspect the inside of the firebox and above the baffle plate every week during
use.
Only use manufacturers recommended replacement parts on the appliance.
Maintenance: Chimney Sweeping
Sweeping should be carried out with the correct size brush and rods to suit
the chimney size and type.
As with all appliances regular sweeping of the flue is essential to avoid the
danger of a blockage and escape of poisonous fumes.
Access for cleaning should be incorporated into the chimney (e.g. soot door,
access through the register plate etc.)
Any existing chimney should be swept prior to installation of the stove, and
then again a second time within one month of regular use after installation to
establish the frequency of sweeping required.
14
This should be done by and competent person such as a NACS chimney engineer
who will provide a Certificate of Chimney Sweeping.
Sweep the whole flue way, including the outlet at least twice a year per
burning season.
It is important that the flue ways, flue pipe and chimney be cleaned prior to
lighting the fire after a prolonged shut-down period.
Maintenance: Removing Fire Rope
Periodically visually check over the door rope seal for any damage, cuts or
tears and detached sections.
The rope gasketing can be replaced, using a universal roping kit.
Instructions for rope replacement are as follows:
· Ensure the appliance is cold
· Unscrew the hinges and lift the door off the appliance and lay onto a flat
surface with the rear face upwards
· Carefully remove the old rope gasket and old adhesive.
· Take note of the layout of the rope seal. Ensure no traces of the old
adhesive or rust / flaky paint is present, as this will result in an unsound
joint.
· Apply the rope adhesive following the instructions on the bottle
· Press the rope gasketing into the channel on the rear door casting,
following the same layout as the old rope seal.
· Just before the final end, cut the rope seal to length and glue into
position.
· Allow at least 30 minutes before refitting the door to the appliance.
Stove Rope
15
Maintenance: Replacing Baffle Plate
Prior to installation, internal components of the stove including the baffle
are removed to gain access to fixings and to make it lighter for installation,
so it is important that the baffle plates are fixed back into position
correctly by the installer before lighting of stove occurs.
If the baffle plates are loose, shifting or falling down, this is an indicator
they are not fixed correctly and they simply need to be repositioned back into
place. Please observe the instructions.
· Replace the rope gasket, remove the self adhesive backing on the rope as you
go, start at the bottom of the window, centrally. Push the adhesive side of
the rope into the grove on the rear of the door casting gradually work your
way round until the ends of the rope meet. Re-seat the new glass, ensuring the
glass sits fully against the gasket.
· Replace the four retaining clips and fixing screws. Do not over tighten the
fixings as damage may occur to the glass.
· Refit the door assembly back onto the stove, carefully lift the door over
the hinge pins and slot into place
Maintenance: Replacing Door Glass
In the event of the door glass being broken it can easily be replaced using
the following procedure: · Ensure the appliance is cold. · Lift the door off
the appliance and lay onto a
flat surface with the rear face upwards. · Unscrew the four screw fixings
securing
the glass clips and remove both clips, and fixings. · Carefully remove any
pieces of broken glass and sealing gasket. Wear suitable gloves for this
procedure. Take note of the position and joint of the rope gasket.
Stove Door Glass
Maintenance: Replacing Fuel Retainer
Lift fuel retainer clear of the supporting brackets. Pull directly up to clear
the sides of the door opening. Do not use appliance without the fuel retainer
in position.
16
Air Controls
Henley Stoves appliances have air systems providing cleaner burning, and
greater efficiency and control. Please see diagram to view where the various
air controls are located on your Henley Stove 1) Primary Air – Pulling out the
lever on the bottom of stove opens the primary air and allows air into the
stove. You would normally open this when starting a fire to allow air into the
stove for maximum combustion.
Pull out lever to Open Primary Air Supply Push in lever to Close Primary Air
Supply
Stove Air Controls
Useful Information
Properly installed, operated and maintained, this appliance will not emit
fumes into the room.
Occasional fumes from de-ashing and refuelling may occur.
Persistent fume emission is potentially dangerous and must not be tolerated.
If fume emission does persist: · Open doors and windows to ventilate the
room. · Leave the room. · Allow fire to burn out and safely dispose of
fuel from the appliance. · Check for chimney blockage and clean if
required. · Do not attempt to relight until the cause of the
emission has been identified and corrected · If necessary seek expert advice.
· All open flued appliances can be affected by
temporary atmospheric conditions which may allow fumes to enter the house. ·
Because of this an electronic carbon monoxide detector conforming to the
latest edition of BSEN50291 must be fitted in the same room as the appliance.
· The existence of an alarm must not be considered a substitute for ensuring
regular servicing and maintenance of the appliance and chimney system. · If
the alarm sounds follow the instructions given under Warning above.
DO NOT LEAVE AIR LEVERS / RODS
FULLY OPENED FOR LONG PERIODS.
We Recommend to Never Open More than 60%, As Extended Use of Stove at More
than 60% Proficiency May Damage Stove.
DO NOT USE YOUR BARE HANDS
Stove Parts become very hot while the stove is running so should not be
touched with bare hands. Special operating tools and or a glove are
provided for operation of the hot stove.
17
Stove Finish (Paint)
The outside of the stove is finished in a durable high temperature paint.
It is best cleaned by brushing down with a soft brush.
Do not allow water to remain on the surface where cold or rust may occur.
The high temperature paint finish should not require attention for some time,
depending on use.
The hotter the fire is burned, the sooner repainting will be necessary.
Aerosol tins of paint are available for complete refurbishing from Henley
Stoves.
Repainting Instructions: · Make sure the stove is out and cold · Remove door
glass · Lightly brush the body of the stove with a wire
brush & rub down with wire wool. This will remove any loose paint powder. ·
Mask or remove items such as brass work. · Adjacent brickwork, mantelpiece,
hearth etc., should be carefully masked for quite a distance around the
appliance. (this precaution is to prevent the discoloration of the surrounding
brickwork, wallpaper etc). · Re-spray in a well ventilated area, avoid
breathing the vapor. Refer to the safety instructions on the paint can. · When
paint is dry refit door glass and any other parts previously removed. · Leave
to dry for 8 hours and refit the door glass etc. · Burn slowly for the first 4
hours, then build up heat gradually to cure the paint.
USE ONLY GENUINE HENLEY STOVES SPRAY PAINT as some paints interact and spoil
the stove finish & will invalidate the warranty.
Chimney Fire & Over-firing
DO NOT OVER FIRE YOUR APPLIANCE. Over firing your stove will cause the paint
to peel off your stove and is not covered in our warranty.
Using any flammable liquids, or too much fuel, or firing the stove at maximum
for prolonged periods may result in over firing.
If the chimney connector or casing starts to glow red, the appliance is being
over-fired.
This may result in a chimney fire.
If a Chimney Fire Occurs :
· Call the Fire Service – Dial 999 or 112 · Immediately close all of the air
inlets to
the appliance to reduce the air supply to the fire. · Move items of furniture
and combustibles away from the stove to reduce the risk of a fire, and allow
access for the fire service. · Ensure access to the loft space is available ·
Evacuate the property
NOTE: The Chimney fire may have caused structural damage to the chimney.
Do not use the stove again until the stove, chimney and connector have been
inspected, and any damage parts have been repaired or replaced.
This work should only be carried out by a HETAS / METAC registered engineer.
Carbon Monoxide Alarm
As part of act SI.9 and TGD Part L (2014) it is now mandatory to install a
Carbon monoxide detectors in any dwelling with combustion and discharge of
combustion gases from heat producing appliances”
18
Spare Parts
Over time you may require replacement parts for your Henley Stove. Replacement
parts are available through your local stockist.
Please contact your local stockist to establish the part you require for your
stove. Please ensure you quote model name and also serial number of stove when
ordering spare parts.
ONLY USE GENUINE HENLEY APPROVED REPLACEMENT PARTS FOR YOUR STOVE.
4 6 3
2
1
14
11
15
10
12 8
5 9 13 16 7
Ref NO.
Description
Ref NO.
Description
Ref NO.
Description
Ref NO.
1
Handle
5
Down Baffle
9 External air collar 13
Description Fire retainer
2
Door
6 Left Vermiculite 10
Bottom
14 Fire Retainer Holder
3
Glass
7 Right Vermiculite 11
Control Bar
15 Bottom Vermiculite
4
Top
8
Stove body 12
Up Baffle
16 Metal Floor Rails
MATERIAL
SHEET 1 OF 1
19
Frequently Asked Questions (FAQ’s)
Why are my air inlets puffing smoke? Combustion gases can build up in the
firebox and ignite as small explosions, causing smoke to puff out of the air
inlets and other openings. This occurs if the air controls are shut soon after
adding new fuel to a very hot fire. Stop by opening the air controls to
increase combustion air and burning rate.
What is a flue draught? The chimney has two main functions: 1) To safely
remove the smoke, gases and fumes from the house. 2) To provide a sufficient
amount of draught (suction) in the appliance ensuring the fire keeps burning.
Why is there no heat from my stove? 1) If your stove is installed in an
alcove, you need to cap off the area directly above the stove by installing a
3mm mild steel plinth with
insulation to prevent the heat from escaping.
2) If the fire continues to consume large amounts of fuel you may need to
check the baffle plate is fitted correctly and also if there is too much of a
draw up the chimney.
3) A simple test would be to open the door of the stove when it is not
lighting and listen to see
if you can hear wind in the chimney. If so this
means you will need to install a damper in the
flue to prevent the up draught. We recommend you contact a piping specialist
and install an anti-
up draught cowl.
Draught is caused by the rising hot air in the chimney when the appliance is
lit.
Symptoms of poor performance related to flue draught include: · Excessive fuel
consumption (high flue
draught). · Poor burning control and/or overheating (high
flue draught). · Wind noise from air controls (high flue
draught). · Difficulty getting a fire going and keeping it
burning well (low flue draught). · Low heat output (low flue draught). · Smoke
entering room when doors are
opened (low flue draught). · The construction, position, size and height of
the chimney all affect the performance of the flue draught. · Other factors
effecting the flue draught include nearby trees or buildings causing
turbulence. · We suggest installing a chimney cowl or antidowndraught cowl if
you are experiencing issues with draught in your chimney. · Please note issues
with flue draught is out of the control of Henley Stoves and does not warrant
a service call. · We recommend you contact a chimney specialist if the
addition of a cowl does not resolve a flue draught issue.
I’m finding it very hard to light a fire in my stove? Why is this? 1) In some
houses there may not be sufficient ventilation in the room for the fire to
light effectively. You may need an additional air vent in the room to use the
stove efficiently.
There is smoke coming out of the stove when I light it, why is this? 1) To
ensure maximum efficiency and to prevent the stove from smoking, the pipe at
the back to the stove must be max 150mm before the 45 degree bend in the pipe,
otherwise the smoke will not be able to escape up the chimney. 2) Stoves that
are installed in flat roof houses or extensions may have this issue due to the
structure of the building. It may also be because the chimney of your house is
lower than the highest point of your roof which causes the wind to funnel down
the chimney. We recommend you install a rotary cowl to resolve the issue. We
recommend you get your stove installed by a professional.
Why is the glass on the door of my stove dirty? 1) Simply open the airwash and
pull the lever to the open position and open the primary. The airwash is
normally located above the door of the stove. The glass will become visibly
clean. Please note the glass with become visibly dirty when the fire stops.
20
My grate has already burned out, why is this? 1) Not cleaning the grate after
every fire will result in the grate burning out prematurely.
How often should I clean my chimney? 1) The chimney and the connecting flue
pipe must be swept at least once a year. Ensure you remove any deposits from
the oscillating grates, the firebox surfaces and the flue collar. We recommend
you clean your chimney twice a year.
Annual Service
Before the start of the heating season strip, inspect and clean the appliance
using the following instructions: · Allow appliance to cool. · Remove all
internal parts: baffle, log guard
and firebricks. · Take care handling firebricks as they can
become fragile after a period of use. · Sweep the appliance at this point if
necessary. · Vacuum clean any remaining ash and
debris from the inside of the appliance. · Check the parts for any damage. ·
Replace any damaged parts using genuine
Henley Stoves replacements parts. · Check and clean the firebricks with a soft
brush. · Some surface damage will occur during
use. The life of the bricks will depend on the type of fuels burnt and the
level of use. · Replace damaged bricks as soon as possible.
· Re-fit cleaned internal parts. · On printed glass surfaces, use Glass
Cleaner. Do not use abrasive cleaners to remove tar or soot deposits from the
glass. · Fit new door rope seal · Lightly oil the door catch mechanism and
hinge pins. Avoid getting oil onto the door seals and glass.
Seasonal Use
Remove the baffle and inspect the inside of the stove and the flue ways and
ensure they are 100% clear after a period of disuse, for example if the stove
is not used during the warmer periods of the year.
Also set the air controls half open to keep the appliance ventilated and stop
the build-up of any moisture inside.
Ventilation
According to Building Regulations 2014 for Heat Producing Appliances, Any room
or space containing an appliance should have a ventilation opening (or
openings) of at least the size shown below
For appliances designed to burn a range of different solid fuels the air
supply should be designed to accommodate burning the fuel that produces the
highest heating output.
Air Supply to Non-Room Sealed Solid Fuel Appliances
Open Flue Solid Fuel Appliances should have a permanent ventilation opening of
free area of at least: · 6,500 mm² where air permeability is
greater than 5.0 m³/(hr.m2), or · 6,500 mm² + 550 mm² per kW of rated
output above 5 kW where air permeability is less than 5.0 m³/(hr.m2).
Note: It is unlikely that dwellings built prior to 2008 would have an air
permeability of less than 5m3/(hr.m2), at 50 Pa unless extensive air tightness
measures have been carried out
21
Henley Stoves Terms & Conditions
You need to register your warranty online at.
https://henleystoves.com/warranty/ Failing to register your stove will only
give you standard Henley Warranty.
Warranty Terms & Conditions
Room Heater Stoves 5 Year Warranty · 1 year standard manufacturers warranty
as in accordance with EU regulations. · 2 year standard Henley warranty · 2
year extended Henley warranty will be added if stove warranty is registered
online within first 3 months of
purchase of your new Henley room heater stove. Boiler Stoves 3 Year Warranty
· 1 year standard manufacturers warranty as in accordance with EU regulations.
· 2 year standard Henley warranty.
Stove Fitting / Installation
· The appliance must be installed by a HETAS / METAC approved fitter in
accordance with Building Regulations in order for the warranty to be valid.
· If upon opening the stove, it is found to be damaged in any way, do not
attempt to install the stove. Return to retailer where it was purchased from.
· Please ensure that the appliance is the correct size (kW) to effectively
heat the room where it is to be installed to avoid poor performance issues.
Warranty Limitations
· Grates and baffle plates are guaranteed for 1 year. · There is no guarantee
on glass and fire bricks. · Please note Fire Bricks will develop hairline
cracks over time & only need to be replaced upon total
disintegration of the brick, where you can see metal side of stove. · Please
note issues such as replacing fire rope, replacing the door handle, paint
peeling, bricks cracking,
replacing grate, glass or baffle doesn’t warrant a service call & can be
easily done using manual instructions
Terms of Warranty
This warranty is only valid if: · The unit has been installed in accordance
with the latest building regulations. · The chimney which services the stove
is in accordance with the latest building regulations. · All installation
instructions in the manual have been followed. · The stove is operated as
described in the manual. · The stove is only used to burn fuel as described in
the manual. · Any stove installed must have a rain cap fitted to the top of
the chimney.
This Warranty Does Not Cover:
· Damage resulting from the use of fuel not recommended in the manual. · Where
a crack appears on top of stove, resulting from a layers of pipework placed
all the way to ceiling
with no twin-wall adapter or joist support to carry the weight of these pipes.
· Parts which are damaged by external causes such as unadapted chimneys,
thunderstorms. dampness.,
faulty plumbing, faulty fuel and mistreatment. · Any nuts or bolts of handles
that become loose due to use or mistreatment · Body paint peeling / Enamel
Cracking due to stove being over-fired · Breakage of glass · If the appliance
is not serviced on a yearly basis according to instructions below.
Annual Service
Once a year service should be completed by a HETAS / METAC approved fitter.
Service Checklist: 1) Door is sealed correctly. (You may need to change fire
rope & also adjust locking nut on door handle.) 2) Remove all consumable parts
– baffle, grate, fire retainer & bricks. Clean & Examine, replace if damaged.
3) Examine all paintwork. If paint has faded, stove may need to be repainted
due to over-firing. 4) Ensure that chimney or flue system is installed &
supported correctly & that all joints are sealed properly.
Henley Stoves Terms & Conditions
Replacement Parts
· Replacement parts are available through your local stockist. · Please
contact the shop where you purchased your stove in order to clearly identify
the replacement part you
require. · If you are unsure where the stove was purchased, please visit our
website
www.henleystoves.com/stockists/ to find a list of your local stockists. · If
you contact Henley Stoves directly regarding replacement parts you will be
directed to our website or
forwarded to your local stockist.
Maintenance
· Neglecting to regularly service your Henley Stove or maintain it to an
acceptable standard IE if parts are clearly damaged, burnt out & not replaced.
· Failure to replace consumable parts in your stove will result in irreparable
damage to stove & will invalidate your warranty
Boiler Stoves – Installation & Maintenance
· Henley Stoves advise that you consult with a heating specialist to determine
the correct size & BTU’s for your heating requirements, before you install a
Boiler Stove.
· We strongly recommend that our stoves are plumbed independently. We do not
advise you use a dual system which incorporates both oil & solid fuel, running
at the same time. In our experience this system does not work.
· If you are experiencing an issue with the plumbing such as no hot water
being pushed to the radiators or a low heat output to the room, Henley Stoves
can only offer advice.
· Henley Stoves can recommend a name of an independent service engineer to
determine if there is an issue with the stove or the plumbing.
· The service engineer will provide a detailed report outlining any issues (if
any) at a cost to you for 450 (this fee may vary depending on location) which
is prior to any inspection. Once a report is received from a qualified
engineer, Henley Stoves will asses & make a decision based on the report’s
results.
· We strongly recommend only qualified HETAS / METAC approved plumber
installers as unqualified installers will void your warranty.
· Failure to fit a rain-cap will cause water to come down chimney & pool on
top of stove. This will cause severe corrosion & has in our experience been a
leading cause in Boiler Stoves leaking.
· If we find the stove has been flued out the top with no rain cap fitted, the
warranty is null & void. · We also require proof of maintenance and/or
detailed service record in order for warranty to be valid. · Henley Stoves can
only replace a Boiler stove found with a leak after it has been delivered to
our warehouse
for a forensic examination. After examining we will determine if the stove
should be replaced or not. · We will not cover any additional costs of
plumbing or labour.
Insert Boiler Stoves
· Insert Boiler Stoves are primarily designed to heat water to radiators. · In
some cases if the stove is running too many radiators, the heat output can
vary from 2kW to 5kW heat
output to the room. · We strongly recommend that a radiator is fitted in the
room where the stove is installed, to maximize heat
output to the room.
Downdraught
· If you are experiencing an issue when refueling the stove, i.e. smoke
spilling back into the room, in our experience this is caused by the stove
being fitted in a bungalow or chimney stack is too low.
· You will need to contact a chimney specialist to rectify this problem.
Henley Stoves can only offer advice.
Contacting Henley
The fastest way to help a customer who has an issue with one of our stoves, is
to email service@henleystoves.com with the following: 1) Customer’s full name
& address & telephone number 2) Name of the shop where you purchased the stove
3) Name & telephone number of the person who fitted the stove. 4) Detailed
photographs of issue with stove 5) Brief description of the problem in
writing. Once we receive this information, we will contact the customer to
resolve the situation.
Henley Stoves, Curraheen, Tralee, Co. Kerry, Ireland Tel: 066 7119788 | Fax: 066 7124200 Email: info@henleystoves.com www.henleystoves.com
References
- Stockists – henleystoves
- Planning permission: When you need it - GOV.UK
- Smoke control areas: the rules - GOV.UK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>