STOVES ARE US PCRMSB Portway Arundel Deluxe 5kW Multi-Fuel Stove Instruction Manual
- June 9, 2024
- STOVES ARE US
Table of Contents
- STOVES ARE US PCRMSB Portway Arundel Deluxe 5kW Multi-Fuel Stove
- Installation and Operating Instructions
- Stove Information
- Stove Installation Requirements
- Stove Flue Connection to the Chimney
- Suitable Wood fuel for the Portway Arundel Deluxe Stove – User
- Suitable Mineral fuel for the Portway Arundel Deluxe Stove – User
- Operation of the Portway Arundel Deluxe Stove – User Instruction
- Troubleshooting
- Removal & re-fitting the stove throat plate
- Removal & re-fitting the smoke stop
- Spare Parts
- guaranteed
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
STOVES ARE US PCRMSB Portway Arundel Deluxe 5kW Multi-Fuel Stove
Arundel Deluxe
Model No. PCRMSB
Installation and Operating Instructions
Eco-Design 2022 Compliant
Multi-Fuel Stove
Read these Instructions and use only the recommended fuels
Leave this manual with the householder following installation
To find a qualified installer, fuel supplier or chimney sweep please contact |
---|
UK -
- The Solid Fuel Association
- 7 Swanwick Court Alfreton
- Derbyshire
- DE55 7AS
- Tel : (0845) 601 4406 www.solidfuel.co.uk
R.O.I. –
- Irish Nationwide Fireplace Organization
- 162 Capel Street
- Dublin
- Tel (01) 801 5959
- www.fireplace.ie
This Portway Arundel Deluxe Stove may be used in smoke control areas when
operated strictly in accordance with these instructions and with Soliftec
Smoke Advice Sheet No. 1
(www.soliftec.com/smokeadvice.htm)
when burning :
UK : Untreated wood logs or authorised smokeless fuels (exempted from s20
of the clean air act 1993)
ROI : Wood logs, smokeless fuels, but not petroleum coke (Control of
Atmospheric Pollution Regulations, 1970)
Information Requirements for Commission Regulation (EU) 2015/1186
- Model Identifier PCRMSB
- Indirect Heating Functionality No
- Direct Heat Output 5.0kW
- Indirect Heat Output Not Applicable
- Fuel Wood logs with moisture content <25%
- Other Suitable Fuels
- Compressed wood with moisture
- content <12%, Anthracite and dry
- steam coal, Low temperature coke,
- Lignite briquettes, Blended fossil fuel briquettes.
- Nominal Heat Output (Measured) 5.0kW
- Minimum Heat Output (Indicative) 3.0kW
- Seasonal / Useful Efficiency at Nominal Heat Output 82.5%
- Useful Efficiency at Minimum Heat Output (Indicative) 50.0%
- Energy Efficiency Index 110%
- Auxilliary Electricity Consumption at Nominal Heat Output Not applicable
- Auxilliary Power Consumption at Minimum Output Not applicable
- Auxilliary Power Consumption at Standby Mode Not applicable
- Permanent Pilot Flame Requirement Not applicable
- Type of Heat Output / Room Temperature Control Single stage heat output, no room temperature control
- Harmonised standard applied BS EN 13240:2001+A1:2004
- Notified Body KIWA 0558
- Contact Details BFM Europe Ltd.
- Gordon Banks Drive
- Trentham Lakes North
- Stoke-on-Trent
- ST4 4TJ
- Tel : 01782 339000
Stove Information
This Portway Arundel Deluxe multi-fuel stove meets the safety and performance requirements of European Standard EN 13420 for intermittant burning solid fuel roomheaters for installation in a dedicated chimney when operated in accordance with these instructions. Independently tested by KIWA, Cheltenham, UK.
Stove Dimensions – see figure 1 below.
The stove is supplied with the following loose items :-
1 off ashpan, 1 off ashpan handle tool & 1 off stove glove.
Section 2 – Stove Performance Data
Signed for and on behalf of Portway Stoves (Manufactured by BFM Europe
Limited).
W. Bridgett ………………………………….. Technical Director – 27th April 2002
Fuel | Wood (Beech) | Mineral Fuel (Maxibrite) |
---|---|---|
Test standard | EN 13240 : 2001 + A2 2004 | EN 13240 : 2001 + A2 2004 |
Re-fuelling Interval | 0.85hrs | 1.04hrs |
Flue draught (Pa) (ins WG) | 12 (0.05) | 12 (0.05) |
Efficiency | 82.5% | 78.8% |
Recommended output (kW) | 5.0 | 5.0 |
Mean flue gas temperature (oC) | 272 | 305 |
Minimum air entry requirement | 2700mm2 | 2700mm2 |
Minimum clearance to combustible surfaces | 500mm Rear, 600mm Side. | 500mm |
Rear, 600mm Side.
Emissions if O2 = 13%| |
CO %| 0.07| 0.06
Flue gas mass flow (g/s)| 3.4| 3.4
Mean CnHm (Nmg/m3)| 43| 9
Mean NOx (Nmg/m3)| 112| 123
DIN Plus Dust (Nmg/m3)| 8| 13
Stove Installation Requirements
WARNING – Installing a stove is a controlled service, the law requires
that the installation is completed by a qualified installer or that the
building inspector is in formed. Check with your local authority.
ASBESTOS – This Partway stove does not contain asbestos, but asbestos
material may be encountered during installation of the stove. If in doubt
contact a suitably qualified professional to deal with Asbestos or material
suspected to be asbestos.
WEIGHT – Your stove is heavy 65kg Net (78kg packed) – take care when
moving it and ensure that the fireplace to which you are attempting to install
it can take the weight – consider the use of a load distribution plate.
FIREGUARD – This stove becomes extremely hot is use, therefore a
fireguard should be used if children, the elderly or infirm are present.
FIREPLACE – Stoves become extremely hot within use, therefore the
fireplace to which the stove is installed must be made from durable fireproof
materials. Thin stone slabs (less than 50mm) risk cracking unless cut into
sections to allow for expansion and backed by heat resistant concrete. Even
beyond the safety clearances stated items subjected to radiant heat from the
stove can still become extremely hot, therefore please take care when siting
items such as fuel, paper etc.
AIR SUPPLY – Your stove needs air to breathe and therefore perform
correctly. There must be a permanent fresh air supply into the space to which
it is installed equal to 550mm2 for each kW of output. This can often be
provided by air leaking around door frames etc. It is commonly accepted that
this level of adventitious ventilation alone may suffice for stoves of output
less than 5kW but in the case of any doubt, fit a purpose made air vent. If an
extractor fan is fitted in the room, any interconnecting room or room in the
vicinity can detrimentally affect the performance of the stove so please check
stove performance with these extraction fans in operation. Where there are
additional combustion appliances within the property please ensure that the
relevant requirements of Approved Document J of the Building Regulations are
complied with.
When air inlet grills are positioned to provide combustion air they must not
be liable to blockage. Regular checks should be made to ensure that any air
inlet grill is not obstructed.
REGULATIONS & HEARTH REQUIREMENTS: All local regulations including those
referring to National and European standards need to be complied with when
installing this stove. Refer to the current version of BS 8303, Code of
Practice for installation of domestic heating and cooking appliances burning
mineral fuel. Refer to the current version of BE EN 15287-1, Design,
Installation and Commissioning of Chimneys.
The hearth should extend a minimum at least 400mm in front of the stove
and 200mm to each side and be capable of with standing 141 degrees C.
A minimum of 100mm clearance to non-combustible
materials is required at each side of the stove for access for servicing and
maintenance.
There must be no combustible material positioned within 1000mm of the stove
that could be affected by heat.
CHIMNEY – The chimney must conform to the following requirements :-
Generate a draught when in use of minimum 12 Pa (0.05 ins WG).
Have a minimum internal cross section equivalent to not less than 125mm
diameter or rectangular / square flues having the same cross sectional area
and a minimum dimension not less than 100mm for straight flues or 125mm for
flues with bends or offsets. Minimum effective height is 5 meters.
Be capable of withstanding the flue gas temperatures generated by the stove.
Terminating at least 1 meter above the ridge.
Be free from any cracks or sources of leakage and be sealed throughout its
entire length to prevent leakage of products of combustion into the property.
Have no bends greater than 45 degrees.
Have no obstructions and having been swept throughout its entire length.
Being connected only to this Partway stove.
Conforming to local building regulations and rules in force.
Being adequately insulated.
Where the flue passes through timber or thatch or venerable materials
specialist advice must be sought.
THIS APPLIANCE MUST NOT BE INSTALLED ON A SHARED FLUE SYSTEM.
APPLIANCE EXEMPTION UNDER SECTION 21 OF THE CLEAN AIR ACT 1993 AND SMOKE
CONTROL AREAS
The Partway Arundel Deluxe multi-fuel free-standing stove, model number PCRMSB
has been exempted under the Clean Air Act 1993 for use in smoke control areas
when burning wood logs when it is fitted with the smoke control stop
preventing the closure of the secondary air controls and tertiary air controls
beyond 8mm.
Under the Clean Air Act local authorities may declare the whole or part of the
district of the authority to be a smoke control area. It is an offence to emit
smoke from a chimney of a building, from a furnace or from any fixed boiler if
located in a designated smoke control area. It is also an offence to acquire
an “unauthorized fuel” for use within a smoke control area unless it is used
in an “exempt” appliance (“exempted” from the controls which generally apply
in a smoke control area).
In England appliances are exempted by publication on a list by the Secretary
of State in accordance with changes made to sections 20 and 21 of the Clean
Air Act 1993 by section 15 of the Deregulation Act 2015. Similarly, in
Scotland appliances are exempted by publication on a list by Scottish
Ministers under section 50 of the Regulatory Reform (Scotland) Act 2014. In
Northern Ireland appliances are ex emptied by publication on a list by the
Department of Agriculture, Environment and Rural Affairs under Section 16 of
the Environmental Better regulation Act
(Northern Ireland) 2016. In Wales appliances are exempted by regulations made
by Welsh Ministers and by the department of the environment respectively.
Further information on the requirements of the Clean Air Act can be found here
: http://smokecontrol.defra.gov.uk
Your local authority is responsible for implementing the Clean Air Act 1993
including designation and supervision of smoke control areas and you can
contact them for details of Clean Air Act requirements.
APPLIANCE EXEMPTION UNDER SECTION 21 OF THE CLEAN AIR ACT 1993 AND SMOKE CONTROL AREAS (CONTINUED).
Refueling on to a low fire bed
If there is insufficient burning material in the fire bed to light a new fuel
charge, excessive smoke emission can occur. Refueling must be carried out onto
a sufficient quantity of glowing embers and ash that the new fuel charge will
ignite. If the fire bed is too low or cool, suitable kindling must be used to
re-light fires.
Fuel overloading
The maximum amount of fuel specified in this manual must not be exceeded,
overloading can cause excessive smoke.
Operation with door left open
Operation with the door left open can cause excessive smoke. The appliance
must not be operated with the door left open except as directed in these
instructions for refueling purposes.
Dampers left open
Operation with the air controls or dampers left open can cause excessive
smoke.
The appliance must not be operated with the air controls left open except as
directed in the instructions.
REQUIREMENTS TO FIT A CARBON MONOXIDE (CO) ALARM
When this stove is installed, Building Regulations require that whenever a new
or replacement fixed solid fuel or wood/biomass appliance is installed in a
dwelling a carbon monoxide alarm must be fitted in the same room as the
appliance. Further guidance on the installation of the Carbon Monoxide alarm
is available in the latest version of BS EN 50292 and from the alarm
manufacturers instructions.
IMPORTANT NOTE : The installation a Carbon Monoxide (CO) alarm is not a
substitute for installing the appliance correctly, regular servicing and
maintenance of the chimney / flue or the stove itself. Please ensure that
regular servicing in accordance with section 7.6 of this manual is completed.
WARNING NOTE : Properly installed, operated and maintained this stove
stove will not emit fumes into the dwelling. Occasional fumes from deashing
and refueling may occur. However, persistent fume emission is potentially
dangerous and must not be tolerated. If fume emission does persist the
following action must be taken:-
Open windows and door to ventilate the room and then leave the premises.
Let the fire go out.
Check for chimney blockage and clean if required.
Do not attempt to re-light the fire until the cause of fume emission has been
identified and corrected. If necessary seek expert advice.
The most common cause of fume emission is flueway or chimney blockage. For
your own safety these must be kept clear at all time.
Stove Flue Connection to the Chimney
The flue can be connected to the stove via either the top or the rear outlet.
The stove can then be sealed to the chimney using a short length of
uninsulated flue pipe as shown below and overage in figures 2, 3 & 4.
Top flue outlet into existing chimney – figure 2
Top flue outlet sleeved through wall into external insulated flue – figure 3
Rear flue outlet into chimney with sealing collar – figure 4
Rear outlet by “tee” piece with cleaning door – figure 5
IMPORTANT INFORMATION – whichever method is used it is imperative that the route from the stove to the chimney terminal is completely air-tight, even very small air gaps can adversly affect the flue draught. Seal all joins with fireproof cement and / or heatproof rope. The entire construction should be made of durable fireproof materials.
Suitable Wood fuel for the Portway Arundel Deluxe Stove – User
instruction
SMOKE CONTROL - In certain areas special rules apply regarding the use of
some fuels, please ensure that you check with your local authority. This
Portway Arundel stove may be used in smoke control area’s when operated
strictly in accordance with these instructions and with Soliftec Smoke Advice
sheet No. 1, see front cover of this manual for further details.
WOOD TYPES – All types of wood are suitable providing they are well
seasoned, untreated and have a moisture level of between 12% & 20%. For
softwoods they will need to have been left in storage for 9 months in order
for the moisture to of evaporated. For hardwoods this could take in excess of
18 months for the wood to season. If you are unsure of the moisture content of
your logs it is recommended that you purchase a suitable mositure meter which
will allow you to measure the moisture content of the wood you are planning to
use.
WOOD SIZE - It is recommended that logs should be no greater than 5” /
125mm in diameter and a maximum of 340mm in length. The logs must be dry with
a moisture content no greater than 20%.
WET TIMBER WARNING - Wet timber and logs must not be used as this will
create excess tar deposits in the chimney and the stove and could considerably
increase the possibility of a chimney fire. Wet timber and wood also increases
emissions, creates more smoke and will reduce the lifespan of the stove.
JOINERY WASTE – Burning joinery waste is acceptable, providing the wood
is un treated and dry. Joinery waste generally is softwood and hence will not
burn as cleanly or for as long as hardwood logs.
Suitable Mineral fuel for the Portway Arundel Deluxe Stove – User
instruction
ANTHRACITE – (Smokeless) is a natural hard, shiny form of coal. Slow to
light it can burn for very long periods with great heat. Use the “small” size
of this fuel.
BRIQUETTES - Compressed blocks of fuel, generally able to burn for long
periods. Trade names for these fuels include “Homefire” and “Phurnacite”.
PETROLEUM COKE - THIS FUEL IS NOT SUITABLE FOR USE WITH THIS STOVE. If
used, “Petcoke” (also known as “Longbeach”) will rapidly degrade the interior
of the stove.
HOUSECOAL OR BITUMOUS COAL – THIS FUEL IS NOT SUITABLE FOR USE WITH THIS
STOVE. This fuel is designed for use in open fires, it makes tarry smoke
flammable gas which makes it difficult to control in a closed fire such as a
stove.
IMPORTANT NOTE : DO NOT BURN ANY FORM OF HOUSEHOLD WASTE WITH THIS STOVE AND NEVER USE ANY FORM OF LIQUID FUEL ON THE STOVE.
Operation of the Portway Arundel Deluxe Stove – User Instruction
There are 2 main controls on your stove as shown below in figure 6, namely the primary air control and the secondary air control. The stove is also supplied with a glove and an ashpan handle to be used as described in this section.
Primary air control – This is located at the bottom of the stove on the
left hand side of center. The primary air control allows air into the stove
and under the grate area. Keeping this vent open on start up and when
refueling will allow the fire to get up to temperature quickly.
Secondary air control – This is located at the bottom of the stove on the
right hand side of center. The secondary air control provides an air wash
facility to keep the stove glass clean and provides air for combustion when
burning wood.
Hand glove – a glove is provided with the stove to adjust the air
controls, actuate the riddle mechanism and open / close the door when the
stove is hot. Please note all parts of the stove will become hot in use and
care needs to be taken to avoid injury through burning.
Ashpan & handle – a ashpan and handle is supplied for use with the stove,
please use this in conjunction with the glove and be aware that ash and embers
in the ashpan will be extremely hot. Take care when discarding hot embers.
Smoke Stop – To make sure your stove always receives enough air to burn
away the smoke produced when burning wood, a smoke stop is fitted to prevent
the secondary air control from being fully closed. The smoke stop must always
be in place when burning wood in smoke control areas of the United Kingdom.
Section 6.2 – Lighting the stove – Installer instruction
- Prior to first lighting the stove ensure that the following is complete :-
- Installation of the stove and relevant building work is completed.
- The chimney is suitable, sound and free from obstruction.
- Adequate ventilation and provision for combustion air has been made.
- The installation is compliant with building regulations and local authority regulations as applicable.
- The chimney pull is a minimum of 12 Pa
- The fuels that are planning to be burnt comply with those listed as suitable in section 4 & 5 of this manual.
Section 6.3 – Break-in fires – User instruction
When the stove is new, for the first 20 hours burning only use gentle small controlled wood fires (NO COAL) during which the first three fires must be small kindling wood fires only. This is required to correctly adhere the paintwork on the stove. After the first three fires gently increase the size of the fuel and duration of the burn time. Failure to adhere to this instruction will result in likely damage to the paintwork on the stove. In addition, during the “break in fires” do not touch the paintwork on the stove as during this period the paintwork will be relatively soft and will mark easily.
Section 6.4 – Lighting the stove – User instruction
- When first lighting the stove comply with the following :-
- Ensure that the ashpan is in place
- Ensure that both primary and secondary air controls are in the fully open position (to the left hand side when viewed from the front).
- Construct a pile of kindling in the centre of the grate using approximately 1kg of kindling wood.
- Use a single chemical firelighter in the base of the kindling and light with an approprate ignition source. Leave the door partially open but do not leave the area of the stove.
- As soon as the fire is established in the kindling, shut the door of the stove. After 5 minutes or as soon as the kindling is well lit, add a further 3 small pieces of wood of approximate weight 1kg.
- Once these logs are lit, after a further 5 minutes add a further 2 logs weighing approximately 1.2kg.
- Once these logs are lit, reduce the settings on the primary and secondary air controls to a suitable level to suit your requirements.
- Re-fuel as per section 6.5 as and when required.
- DO NOT OPERATE THE STOVE WITH THE DOOR PERMANENTLY OPEN. This stove is not suitable for connection to a central heating system.
- THIS STOVE MUST NOT BE USED AS AN INCINERATOR AND ONLY USE RECOMMENDED FUELS.
- IF BURNING WOOD IN SMOKE CONTROL AREAS PLEASE READ AND COMPLY WITH THE REQUIREMENTS OF SECTION 2.9
Section 6.5 – Re-fuelling the fire – User instruction
- When refuelling the stove, follow the procedure as detailed below :-
- Open the primary air vent to the fully open position.
- Add up to 1.2kg of wood or mineral fuel.
- After approximately 2 minutes or when the flames from the fresh fuel are fully established, close the primary air vent.
- At high power output your stove will require re-fuelling approximately every hour. Do not leave the stove until the newly added fuel is well established.
- Always refuel onto hot embers and riddle at each refuel.
- If the fire has died out at the point of refuelling use kindling to re-establish the fire.
- DO NOT OVERLOAD THE STOVE WITH FUEL.
- Reduced burn rates can be achieved via use of the primary and secondary air controls.
- This stove is suitable for intermittant burning and should not be used constantly for extended periods. Not suitable for overnight burning.
- During certain atmospheric conditions it may be difficult to achieve the required flue draught. If such conditions occur it may require a specialist cowl on the chimney to achieve the correct flue draught to ensure correct operation of the stove. In such circumstances do not use the stove and obtain expert advice.
- In the event of a chimney fire, close the primary and secondary air controls to the stove, evacuate the building and call the fire brigade.
Section 6.6 – Maintenance – If in doubt contact a competent person
- Regular cleaning and maintenance of the stove is essential for safety and efficiency.
- Portway recommend a suitably qualified (HETAS) registered engineer is used for servicing purposes.
- Ensure the following steps are completed regularly :-
- The ashpan should be emptied after every use and during use when refuelling as required.
- When the stove is cold, clean out any build of ash or unburnt fuel from the grate, around the ashpan and in any nooks or crannies of the stove.
- Complete monthly as a minimum, including on top of the stove throat plate, see section 8.
- The flue, flue pipe and chimney will require regular sweeping to minimise the build up of soot and tar, annually as a minimum.
- The stove should of been installed with suitable access doors in the flueway to achieve this.
- However in the event that suitable access doors have not been installed access to the flue can be achieved by removal of the throat plate in the stove itself, see section 8.
- If the stove door glass is stained, it may be that the secondary air control may need to be opened up during use, this is dependent upon many factors such as flue pull etc. In the event of excessive staining use a ceramic glass cleaner to re move the marks when the stove is completely cool.
- Note that the internal boards of the stove will craze with normal use, this is not a fault of the boards.
- Cracks will not adversly affect the stove’s performance providing the boards remain in position.
- If pieces break from the boards then replace the boards as necessary.
- You can significantly increase the life of the boards by burning the correct fuels in the stove as detailed in section 4 for wood fuels and section 5 for mineral fuels.
Troubleshooting
In the unlikely event of experiencing problems with your stove, please consult
the following :-
Smoke from the chimney – a little smoke will be emitted from the
chimney when the fire is cold. Ensure the correct, dry wood or smokeless fuels
to prevent smoke emissions.
Poor heat output – this Portway Arundel Deluxe stove will generally heat
a room of 12m3 room volume per kW of heat output, so if operating at 5kW
output it could heat a room of 12m3 x 5 = 60m3 or 5 metres square. The actual
size depends upon factors such as insulation and air change within the room.
To attempt to use too smaller stove to heat too larger room will result in
overheating the stove and potentially damaging it.
Lack of controllability – some fuels may burn excessively until the gases
in them have been used up, you can reduce this effect by using the air
controls on the stove.
Difficulty burning for extended periods – If the fire goes out with
plenty of fuel in the stove, try leaving the air controls open a little more.
Check the door seal is sound and that there are no gaps or cracks in the flue
or flue joints. For longer burn periods use mineral fuels such as
“anthracite”.
Overtiring – If the stove is left with the air controls in the open
position for too long this will result in overfiring, excessive chimney
temperatures and risk of component failure and chimney fires. Use a stove
thermometer, available from your Portway stockist can help to obtain a
satisfactory burn temperature.
Smoke coming into the room – Product of combustion (fumes) are poisonous
and hence smoke emission must never be tolerated. If smoke comes back into the
room when the stove is lit the cause must be fully investigated to ascertain
the problem and rectified before using the stove. Check for build up of ash on
the throat plate, the condition of the door seals, the condition of the seal
between flue and chimney and any air ventilation into the room is not blocked.
If the symptoms persist, consult a suitably qualified person, such as a HETAS
registered engineer to further investigate and resolve the problem.
Removal & re-fitting the stove throat plate
If in doubt contact a competent person
- Ensure that the stove is cool.
- Open the stove door.
- As shown in figure 7 below remove the throat plate from the stove, this is completed by sliding the primary (vermiculite) throat plate forwards slightly until it is clear of the rear fibre board. Then tilt downwards and backwards slightly. Finally rotate downwards and remove from the door of the stove.
- Remove the secondary throat plate by unhooking from the rear brackets unbolting from the internal roof of the stove. Clean off any fly ash etc. If using throat plate removal as a form of access to the chimney please ensure any debris that comes from the chimney is fully removed from the stove before attempting to refit the throat plate.
- Replace in reverse order.
- Check the stove for correct performance and flue products clearance.
Removal & re-fitting the smoke stop
If in doubt contact a competent person
WARNING : The smoke stop is fitted to ensure that your stove receives
enough air to burn away the smoke when burning wood. The smoke stop is fitted
to prevent the secondary air control being fully closed. If, and only if smoke
is not a concern you may unscrew and remove the smoke stop that was fitted
during the manufacture of your Partway Arundel Deluxe stove. Controllability
and burn times may be improved, but more smoke may also be emitted. The smoke
stops must always remain in place when burning wood in smoke control area’s of
the United Kingdom. Failure to do so invalidates the DEFRA approval of the
stove.
To remove the smoke stop, firstly ensure that the stove is cool.
Locate the smoke stop on the secondary air control as shown below in figure 8.
Remove the heat shield (4 bolts and washers) and the air inlet duct (4 bolts)
Remove the smoke stop by unscrewing the 2 off nuts in a anti-clockwise
direction. Keep the smoke stop in a safe place for future use.
Re-fit in reverse order if necessary.
Spare Parts
IMPORTANT : Only genuine Partway spare parts should be used with this stove and no unauthorized modifications to this stove are permitted.
To order spares parts on line visit : www.bfm-partfinder.co.uk
guaranteed
Due to our policy of continual improvement and development the exact accuracy of illustrations and descriptions contained in this book cannot be guaranteed.
B-1032224 Issue 2
27th April 2022
BFM Europe Ltd.
Trentham Lakes
Stoke-on-Trent
Staffordshire
ST4 4TJ
www.bfm-europe.com
Spare Parts – www.bfm-partfinder.co.uk
Telephone – General Enquiries : (01782) 339000
Telephone – Service : (01782) 339008
References
- Smoke control areas: the rules - GOV.UK
- Home Page - BFM Europe Ltd
- Spares Identification - BFM Europe Ltd
- Fireplace.ie is for sale | www.premiumdomains.ie
- Solid Fuel Association - Advice for consumers & professionals
- Soliftec - Smoke Advice
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>