ADA INSTRUMENTS COSMO 70 Laser Distance Meter Instruction Manual
- June 4, 2024
- ADA INSTRUMENTS
Table of Contents
ADA INSTRUMENTS COSMO 70 Laser Distance Meter
Congratulations on the purchase of laser distance meter ADA COSMO 70!
Permitted use
- Measuring distances
- Computing functions, e.g. areas, volumes, subtractions, Pythagorean calculation
- Storing measurements
The safety regulations and instructions along with the operating manual should be read carefully before initial operation.The person responsible for the instrument must ensure that equipment is used in accordance with the instructions. This person is also accountable for the deployment of personnel and for their training and for the safety of the equipment when in use.
SAFETY INSTRUCTION
Prohibited use
- Please follow up instructions given in the operating manual.
- Do not use instruments in an explosive environment (filling station, gas equipment, chemical production, and so on). Do not remove warning labels or safety instructions.
- Do not open instrument housing, and do not change it’s construction or modification.
- Do not stare at the beam. The laser beams can lead to eye injury (even from greater distances).
- Do not aim laser beams at persons or animals.
- Opening of the equipment by using tools (screwdrivers, etc.), as far as not specifically permitted for certain cases. Inadequate safety precautions at the surveying site (e.g. when measuring on the roads, construction sites and so on). Use the instrument in places where it could be dangerous: on air transport, near manufacturers, production facilities, in places where the work of a laser distance meter can lead to harmful effects on people or animals.
Prohibited use
- Please follow up instructions given in the operating manual.
- Do not use instruments in explosive environments (filling stations, gas equipment, chemical production, and so on). Do not remove warning labels or safety instructions.
- Do not open instrument housing, do not change it’s construction or modification.
- Do not stare at the beam. The laser beam can lead to eye injury (even from greater distances).
- Do not aim the laser beam at persons or animals.
- Opening of the equipment by using tools (screwdrivers, etc.), as far as not specifically permitted for certain cases. Inadequate safety precautions at the surveying site (e.g. when measuring on the roads, construction sites and so on). Use the instrument in places where it could be dangerous: on the air transport, near manufacturers, production facilities, in places where the work of a laser distance meter can lead to harmful effects on people or animals.
STARTUP
Keypad
- ON / Measure
- Area / Volume / Pythagorean measure
- Subtraction / Timer
- Clear / OFF
- Addition / Units
- Reference
DISPLAY
- Laser ON
- Reference (front/rear)
- Area / volume/ Pythagorean
- Mainline
- Line 2
- Line 1
- Units
- Timer On
- Battery display
- Error
Inserting / Replacing Batteries
Remove the end piece on 180º. Remove the battery cover, insert the battery
correctly. Pay attention to correct polarity. Close the battery compartment.
Replace the battery when symbol constantly blinks in the display. Batteries
should be removed in case of danger of corrosion, if the device will not be
used for a long time.
MENU FUNCTIONS
Switch on and off
Press the button (1) to switch on the instrument and laser. Press and hold key
for about 2 seconds to start continuous measuring. The device also switches
off automatically after 3 minutes of inactivity i.e. no key is pressed within
that interval. To switch off the instrument press and hold button (4) for
about 2 sec.
Reference Setting
Default reference setting is from the rear of the device. Press the button (6)
to set the reference: the front or the rear. When the end-piece is folded out
fully, the reference rear is set. You will see the reference symbol on the
display.
Selecting Units
Press and hold the button (5) for 2 sec. until the desired unit is displayed.
Clear-Key
Cancel the last action. Press button (4).
MEASUREMENTS
Single distance measurement
Press button (1) to activate the laser. When in continuous laser mode, press
this button to trigger the distance measurement directly. The instrument will
give the acoustical signal. The result is displayed immediately.
Continuous Measurement
Press and hold the button (1) for about 2 seconds to start continuous
measuring.
Minimum/ Maximum measurement
This function allows the user to measure the minimum or maximum distance from
a fixed measuring point. It is commonly used to measure room diagonals
(maximum values) or horizontal distances (minimum values).
Press and hold down the button (1), until you will hear the acoustical signal.
Then slowly sweep the laser back and forth and up and down over the desired
target point (e.g. into the corner of a room).
Press (1) to stop continuous measurement. The values for maximum and minimum
distances are shown on the display as well as the last measured value in the
main line.
FUNCTIONS
Distance measuring
Press button (5): next measurement is added to the previous one. Press button
(3): next measurement is substracted from the previous one. To complete this
function press button (1). Repeat this function to measure distances. The
result is des-played in the main display area. Previous measured value is
displayed in the first line, last measured value is displayed in the second
line. To finish working in this mode press button (4).
Area
Press the button (2) once.The symbol “area” is displayed. Press button (1) to
take the first measurement (for example, length). Measured value is displayed
in the second line. Press button (1) to take the second measurement (for
example, width). Measured value is displayed in the second line. First
measurement (e.g. length) is displayed in the first line. The result of
measured area is displayed in the main display area.
Addition / Subtraction of areas
Area measuring – see Area. Take the first measurement of area. Press button
(5) to enter the Addition mode or button (3) to enter into the Subtraction
mode. The area value is displayed in the second line. Press button (1) to take
the first measurement (for example, length). Press button (1) to take the
second measurement (for example, width). After the completion of area, press
button (1) , and the result of the addition/subtraction of areas is displayed
in the main display area. If the measurements are not finished, press buttons
(5) (addition) or (3) (subtraction) to continue calculations.
Volume
For volume measurements, press button (2) twice until the indicator for volume
measurement appears on the display. Press button (1) to take the first
measurement (for example, length). The measured value is displayed in the
second line. Press button (1) to take the second measurement (for example,
width). The measured value is displayed in the second line. Area value is
displayed in the first line. Press button (1) to take the third measurement
(for example, height). The measured value is displayed in the second line. The
volume value will be displayed in the main display area and the previous area
value is displayed in the first line.
Indirect measurement
Pythagorean measurement is used in the condition when the object is covered or
has no effective reflect-ing surface and can’t be measured directly. Make
sure you adhere to the prescribed sequence of measurement: All target points
must be in a horizontal or vertical plane. The best results are achieved when
the instrument is rotated about a fixed point (e.g. with the positioning
bracket fully folded out and the instrument placed on a wall) or the
instrument is mounted on a tripod. Continuous measurements can be used. This
function is used for minimum/maximum measurements. The minimum value must be
used for measurements at right angles to the target; the maximum distance for
all other measurements. Be sure that the first measurement and distance are
measured at right angles. Use indirect measurement function.
Indirect measurement – determining a distance using 2 Auxilary
measurements
This function is used when height and distance can’t be measured directly.
Press button (2) 3 times. The symbol “triangle” is displayed. The distance to
be measured is blinking in the symbol triangle. Press button (1) to take
distance measuring (hypothenuse of the triangle). The result is displayed in
the second line. This measurement can be taken in the indirect measurement
function. Press and hold button (1) for 2 sec. After second pressure of the
button (1) maximum value is fixed. The second distance to be measured is
blinking in the symbol triangle. Press button (1) to take distance measuring.
There is a right angle between laser beam and the length you need to measure.
That’s why you should work in continuous mode. Press and hold button (1) for 2
sec. After the second pressure of the button (1) maximum distance is fixed.
The result of the measurement is displayed in the second line. Previous
measurement is displayed in the first line. The result of the function is
displayed in the main display area.
Indirect measurement – determining a distance using 3 measurements
This function is used when it’s necessary to measure diagonals of rectangular
areas, and also for calculations of the length of frameworks, inclined
distances and so on. Press button (2) 4 times. The symbol “triangle” is
displayed. The distance to be measured is blinking in the symbol triangle.
Press button (1) to take distance measuring (side of the triangle) . The
result of the function is displayed in the second line. This measurement can
be taken in the mode of continuous measurement. Press and hold button (1) for
2 sec. After the second pression of the button (1) maximum value is fixed. The
second distance to be measured is blinking in the symbol triangle. It’s very
important to have a right angle between the laser beam and the length you need
to measure. That’s why you should work in continuous mode. Press and hold
button (1) for 2 sec. After the second pressure of the button (1) maximum
distance is fixed. The result of the function is displayed in the main display
area. The previous measurement is displayed in the first line.
Timer
Use a timer for accurate measurements of large distances. Press and hold
button (3) to set stoppage in 5 sec. When you release the button you will see
a time that remains till the beginning of the measurement (in sec). The time
displays on the display. Time reading of last 5 sec. comes with an acoustic
signal. When you hear last signal, the instrument takes a measurement.
MESSAGE CODES
All message codes are displayed with either or symbol telephone receiver (Error). The following mistakes can be corrected.
Info | CAUSE | REMEDY |
---|---|---|
204 | Calculation overflow | Repeat procedure |
252 | Temperature too high | Cool down instrument |
253 | Temperature too low | Warm up instrument |
255 | Receiver signal too weak | Use target plate |
256 | Received signal too strong | Use target plate (grey side) |
257 | Wrong measurement | Use target plate (brown side) |
258 | Wrong initialization | Switch on – off the instrument |
Info | CAUSE | REMEDY |
--- | --- | --- |
Hardware error | Switch on/off the device several times and check if the |
symbol still appears. If so please call your dealer for assistance.
TECHNICAL DATA
CAL | 0.05 to 70* |
---|---|
Accuracy, mm | ±1.5* |
Smallest unit displayed | 1 mm |
Laser class | 2 |
Laser type | 635 nm, <1 mW |
--- | --- |
IP rating | IP 54 |
Automatic switch off | 3 minutes of inactivity |
Battery life, 2 x AAA | > 5000 measurements |
Dimensions, mm | 114×50×25 |
Weight | 120 g |
Temperature range: Storage
Operating
| ****
-25º to +70º
-10º to +50º
- In favorable conditions (good target surface properties, room temperature). Maximum deviation occurs under unfavorable conditions such as bright sunlight or when measuring to poorly reflecting or very rough surfaces. Use target plate for accurate results.
Measuring conditions
Measuring range: the range is limited to 70 m. At night, at dusk and when the
target is shadowed the measuring range without the target plate is increased.
Use a target plate to increase the measurement range during daylight or if the
target has a bad reflection.
Measuring Surfaces
Measuring errors can occur when measuring toward colorless liquids (e.g.
water) or dust-free glass, styrofoam, or similar semi-permeable surfaces.
Aiming at high gloss surfaces deflects the laser beam and measurement errors
can occur. Against non-reflective and dark surfaces the measuring time can be
increased.
Precautions
Please, handle the instrument with care. Avoid vibrations, hits, water, the
effect of heat. During transportation put the instrument into the soft bag.
Note: the instrument should be dry!
Care and cleaning
Do not immerse the instrument in water. Wipe off dirt with a damp, soft cloth.
Do not use aggressive cleaning agents or solutions.
Specific reasons for erroneous measuring results
- Measurements through glass or plastic windows;
- Dirty laser emitting window;
- After the instrument has been dropped or hit. Please check the accuracy;
- large fluctuation of temperature: if the instrument will be used in cold areas after it has been stored in warm areas (or the other way round) please wait some minutes before carrying out measurements;
- Against non-reflective and dark surfaces, colorless surfaces and so on.
Electromagnetic acceptability (EMC)
It cannot be completely excluded that this instrument will disturb other
instruments (e.g. navigation systems); will be disturbed by other instruments
(e.g. intensive electromagnetic radiation nearby industrial facilities or
radio transmitters).
Laser classification
The instrument is a laser class 2 laser product with power < 1 mW and
wavelength 635 nm. Laser is safety in ordinary conditions of usage. ADA COSMO
70 projects visible laser beam from the front part of the instrument. The
instrument is a laser class 2 laser product accortding to DIN IEC
60825-1:2007. It is allowed to use unit following further safety precautions
(see operating manual).
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be free from defects in material and workmanship under normal use for a period of two (2) years from the date of purchase. During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar model at manufactures option), without charge for either parts of labour. In case of a defect please contact the dealer where you originally purchased this product. The war-ranty will not apply to this product if it has been misused, abused or altered. Withiut limiting the foregoing, leakage of the battery, bending or dropping the unit are presumed to be defects resulting from misuse or abuse.
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in operators’ manual. Although all instruments left our warehouse in perfect condition and adjustment the user is expected to carry out periodic checks of the product’s accuracy and general performance. The manufacturer, or its representatives, assumes no responsibility of results of a faulty or intentional usage or misuse including any direct, indirect, consequential damage, and loss of profits. The manufacturer, or its representatives, assumes no responsibility for consequential damage, and loss of profits by any disaster (earthquake, storm, flood …), fire, accident, or an act of a third party and/or a usage in other than usual conditions. The manufacturer, or its representatives, assumes no responsibility for any damage, and loss of profits due to a change of data, loss of data and interruption of business etc., caused by using the product or an unusable product. The manufacturer, or its representatives, assumes no responsibility for any damage, and loss of profits caused by usage other thsn explained in the users’ manual. The manufacturer, or its representatives, assumes no responsibility for damage caused by wrong movement or action due to connecting with other products.
Certificate of acceptance and sale
____№
name and model of the instrument
Corresponds to
designation of standard and technical requirements
Data of issue
Stamp of quality control department
Price
Sold ___ Date of sale ____
name of commercial establishment
WARRANTY CARD
- Name and model of the product ____
- Serial number ____date of sale___
- Name of commercial organization _____stamp of commercial organization
Warranty period for the instrument exploitation is 24 months after the date of the original retail purchase. During this warranty period, the owner of the product has the right for free repair of his instrument in case of manufacturing defects. Warranty is valid only with the original warranty card, fully and clear filled (stamp or mark of the seller is obligatory). Technical examination of instruments for fault identification which is under the warranty is made only in the authorized service center. In no event shall the manufacturer be liable before the client for direct or consequential damages, loss of profit or any other damage which occur in a result of the instrument outage. The product is received in the state of operability, without any visible damages, in full completeness. It is tested in my presence. I have no complaints to the product quality. I am familiar with the conditions of warranty service and i agree.
Purchaser signature ___
Before operating you should read service instructions! If you have any
questions about the warranty service and technical support contact the seller
of this product
WARRANTY DOESN’T EXTEND TO FOLLOWING CASES
- If the standard or serial product number will be changed, erased, removed, or will be unreadable.
- Periodic maintenance, repair or changing parts as a result of their normal runout.
- All adaptations and modifications with the purpose of improvement and expansion of the normal sphere of product application, mentioned in the service instruction, without the tentative written agreement of the expert provider.
- Service by anyone other than an authorized service center.
- Damage to products or parts caused by misuse, including, without limitation, misapplication or negligence of the terms of service instruction.
- Power supply units, chargers, accessories, and wearing parts.
- Products, damaged from mishandling, faulty adjustment, maintenance with low-quality and non-standard materials, presence of any liquids and foreign objects inside the product.
- Acts of God and/or actions of third persons.
- In case of unwarranted repair till the end of the warranty period because of damages during the operation of the product, it’s a transportation and storing, the warranty doesn’t resume.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>