Euro Appliances EM52UMS 52cm Undermount Rangehood User Manual

Euro Appliances EM52UMS 52cm Undermount Rangehood

USAGE AND CARE GUIDE

PRODUCT CODE:

• EM52UMS
• EM70UMS
• EM90UMS

Warnings

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children are not permitted to play with the appliance.

• Cleaning and user maintenance shall not be made by children. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
  or similarly qualified persons in order to avoid a hazard.

• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels. The filter is made of high density aluminum. Please do not use corrosive detergent for cleaning. The proper function of the unit is conditioned by the regularity of the maintenance.

• To protect the main body from corrosion over the long time accumulation of dirt, the cooker hood should be cleaned with hot water with non-corrosive detergent every two months. There is a fire risk if cleaning is not carried out in accordance with the instructions. Do not flambe under the range-hood. There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood is 650mm. Regulations concerning the discharge of air have to be fulfilled. The appliance uses 4 hob elements at most.

Safety Warning

CAUTION : Accessible parts may become hot when used with cooking appliances.

• The appliance is not intended for use by young children or infirm persons without supervisions.

• Young children should be supervised to ensure they do not play with the appliance.
  Plug the power cord to socket outlet with earthing continuity terminal.

• The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purposes.

• The cooker hood and its filter should be cleaned regularly according to the instruction.

• Do not use open flame, or allow oil to go beneath the appliance.

• If there is any fault occurred with the appliance, please call after-sale service department.

• Please keep the kitchen room ventilated.

• Prior to any maintenance, cleaning operation, ensure the power is cut off.

• If the supply cord is damaged, it must be replaced by the manufacturer, service agent or similarly qualified person in order to avoid a hazard. The replaced power cord should be provided by manufacturer or seller.

• If the plug or cord is damaged, please call after-sale service center.

• There is a fire risk if cleaning is not carried out in accordance with the instruction.

• In case of damaged connecting wire, please refer to the manufacturer, after-sale service personnel or other qualified technicians.

• Use the unit according to the instructions to avoid any fire hazard.

• The exhaust air must not be introduced into a smoke flue or chimney that is used for exhausting fumes from appliances burning gas.

• Follow the local laws applicable for external air evacuation.

Measurement

Installation

Here two venting modes, extraction-air mode and recirculation mode, before installing，select one mode.

• Press the lock catch of metal Filter, remove the Filter.

• Remove the stainless steel frame by unfastening the other 2 screws (M4*8)

• Unfastening the screws (ST4*10), remove the lid of terminal box, disconnect the wires to the Commands at the connectors.
• Disconnect the wires to the Light at the connectors.
• Fasten the Hood in the cabinet by using the 12 screws (ST4*18).

• Screw the stainless steel frame back into place using the screws removed as described above.

• Reconnect the wires to the Commands and Light.

• Replace the metal Filter.

• Install the air outlet pipe(optional).

Use

Speed adjustment. See below Fig (for some models).

• Press the Light button, the two lighting lamps will come on. Press it again and the lamps will be turned off.
• Press the High (speed) button, the motor runs at high speed.
• Press the Mid (speed) button, the motor runs at mid speed.
• Press the Low (speed) button, the motor runs at low speed. Press Stop button, the motor will stop running.

Maintenance

Cleaning of the filter

• Removing the metal filter according to Installation (page 7). Put it into a dishwasher with detergent, set the temperature below 60 degrees.
• Please do not use abrasive detergent for it will damage the hood.
• Make sure that the hood is shut off before cleaning.

Changing the filter

• Remove the metal filter according to Installation (page 7). Remove the saturated Activated Charcoal
  Filters(optional), as indicated.

• Fit the new Charcoal Filters, as indicated.

• Replace the Metal grease Filter according to Installtion (page 8).

Replacing the lamp

• Press the lock catch of metal filter, remove the Filter

• Push the lamp from inside to remove the Lamp

• Disconnect the wires from the Lamp

• Connect the wires of the new Lamp

• Push the new Lamp from outside and fix it to the hole.
   | Max Power| Voltage| Picture| Lamp Cap| ILCOS D code
  ---|---|---|---|---|---

Round/ Diameter

: 70mm

|

1.5W

|

DC 12 V

| |

——

|

DSR-1.5-S-70

Trouble Shooting

Light on, but motor does not work.

| The blades are blocked.|
The capacitor is damaged.| Replace capacitor.
The motor is damaged.| Replace motor.
The internal wiring of motor is cut off / disconnected. An unpleaseant smell may be produced.|

Replace motor.

Both light and motor do not work.

| Apart from the above mentioned, check the following:
Light damaged.| Replace lights.
Power cord loose.| Connect the wires electric diagram.| as| per| the

Oil leakage.

| Outlet and the air ventilation entrance are not tightly sealed.| Take down the outlet and seal with glue.
Leakage from the connection of U-shaped section and cover.| Take U-shaped section down and seal with soap or paint.

Vibration.

| The blade, if damaged, can cause vibrating.| Replace the blade.
The motor is not tightly fastened.| Fasten the motor tightly.
The cooker hood is not tightly fixed.| Fixed the cooker hood tightly.

Insufficient suction.

| The distance between the cooker hood and the cooker top is too large.| Readjust the distance.
Too much ventilation from open doors or windows.| Choose a new place to install the appliance or close some doors / windows.

The machine inclines.

| The fixing screws are not tight enough.| Tighten the fixing screw and make it horizontal.
The hanging tight enough.| screws are not| Tighten the hanging screw and make it horizontal.

Electrical Diagram

Electrical diagram see label on main body of the actual product.

Main Parameters

The air flow parameter is tested under conditions of 230V ~ 50Hz when the voltage is 220-240V~50Hz and without carbon filters.

Disposal

Please dispose of it at your local community waste collection / recycling center and ensure it presents no danger to children while being stored for disposal. The plug must be rendered useless and the cable cut off to prevent misuse.

Pronto Service +
Support: 1800 440 335
Email: service@eurostylegroup.com.au
HEAD OFFICE
65 Glynburn Road, Glynde SA 5070
Ph: 08 8165 1012
www.euroappliances.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>