Euro Appliances EBB900SS2 90cm Stainless Steel Canopy Rangehoods User Guide

Euro Appliances EBB900SS2 90cm Stainless Steel Canopy Rangehoods

Alfresco Canopy

Usage and Care Guide

• Product Code: EBB900SS2

Product Information

• Canopy
• Packet of Screws & Brackets
• Plastic Flaps (2)
• Set of Chimney Pieces (Upper & Lower)
• Operating & Installation Instructions

The Alfresco Canopy is suitable for connection to a 240V, 50Hz power supply with a proper earth.

Usage Instructions

1. Read the instruction manual carefully before use.
2. The installation work must be undertaken by a qualified and competent installer in compliance with applicable Australian Standards. Euro Appliances disclaims all liability for any damage or injury caused as a result of not following these instructions for installation.
3. This Canopy is not an outdoor appliance but it can be installed in an alfresco area. The canopy must not be exposed to rain, moisture or dust. Do not install in a location where winds may blow water or dust onto the canopy.
4. If installed above a barbecue, the minimum distance from the cooking grid/plate is 120cm. If installed above a cooking appliance, the minimum distance from the cooking surface is 65cm.
5. This Canopy is suitable for indoor installation but cannot be recirculated.
6. Before installation, ensure the area is clean to avoid suction of any debris such as bits of broken wood, sawdust, etc.
7. The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room). Regulations concerning the discharge of air have to be fulfilled.
8. Place the Alfresco Canopy at a distance of 65cm minimum from the cooking surface of a cooker/hotplate and 120cm minimum from the cooking surface of a BBQ.
9. Fit the plastic flaps to the outlet vent of the canopy by deforming the flaps slightly so that the ends fit into the holes.
10. Fit the supplied Hook to the wall using the 36mm long screws supplied. Fixing method to the wall must be capable of supporting the weight of the Canopy.
11. Lift the Canopy onto the Hook and make sure both left and right hand hooks are engaged.
12. Fit the Flexible Duct (not supplied) to the outlet.
13. Exhaust the Flexible Duct to the outdoors and fit a one way valve to prevent rain & dust entering into the Canopy.
14. Determine the height of the U-shaped section. Line up the holes in the plate with those in the lower U-Shaped section and fix the plate to the wall using the 36mm long screws supplied.
15. Align the holes in the lower corner of the U-shaped section and fit the 9mm screw supplied through each side.
16. Pull up the inner U-shaped section to a suitable height and align it with the upper plate.

Notice

1. Thank you for choosing our Alfresco Canopy. Please read this instruction manual carefully before use.
2. The installation work must be undertaken by a qualified and competent installer in compliance with applicable Australian Standards.
3. Euro Appliances disclaims all liability for any damage or injury caused as a result of not following these instructions for installation.

This Alfresco Canopy is suitable for connection to a 240V, 50Hz power supply with a proper earth.

Contents

• 1 x Canopy
• 1 x Packet of Screws & Brackets
• 2 x Plastic Flaps
• 1 x Set of Chimney Pieces (Upper & Lower)
• 1 x Operating & Installation Instructions

Installation – Requirements

Warning: This Canopy is not an outdoor appliance but it can be installed in an alfresco area in accordance with the following:

• Installation must be performed by a qualified competent installer.
• The canopy must not be exposed to rain, moisture or dust.
• Do not install in a location where winds may blow water or dust onto the canopy.
•  If installed above a barbecue, the minimum distance from the cooking grid/plate is 120cm.
• If installed above a cooking appliance, the minimum distance from the cooking surface is 65cm.
• This Canopy is suitable for indoor installation but cannot be recirculated.

1. Before installation, please ensure the area is clean to avoid suction of any debris such as bits of broken wood, sawdust, etc.
2. Flexible duct bending should be ≥120°.
3. There shall be adequate ventilation of the room when the canopy is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
4. The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
5. Regulations concerning the discharge of air have to be fulfilled.

Installation – Fitting the Canopy.

The Alfresco Canopy must be placed at a distance of 65cm minimum from the cooking surface of a cooker/hotplate and 120cm minimum from the cooking surface of a BBQ.

• Fit the plastic flaps to the outlet vent of the canopy by deforming  the flaps slightly so that the ends fit into the holes (refer to Pic 3 for location of the flaps).
• Fit the supplied Hook to the wall using the 36mm long screws supplied (refer to Pic 1). Fixing method to the wall must be capable of supporting the weight of the Canopy.
• Lift the Canopy onto the Hook and make sure both left and right hand hooks are engaged (refer to Pic 1).
• Fit the Flexible Duct (not supplied) to the outlet (refer to Pic 2).
• Exhaust the Flexible Duct to the outdoors and fit a one way valve to prevent rain & dust entering into the Canopy.
• Determine the height of the U-shaped section. Line up the holes in the plate with those in the lower U-Shaped section and fix the plate to the wall using the 36mm long screws supplied (refer to Pic 3 item 1).
• Align the holes in the lower corner of the U-shaped section and fit the 9mm screw supplied through each side (refer to Pic 3 item 3).
• Pull up the inner U-shaped section to a suitable height and align it with the upper plate (refer to pic 4).
• Fix the upper plate to the wall using the 36mm long screws. Fix the inner U-shaped section to the upper plate using two 9mm screws on either side of the bracket (refer to pic 4).
• Finally, drill two Ø3.5mm holes in line with the 2nd plate where the upper and lower sections overlap. Use a 9mm long screw on each side to fix them together.

Note: Fix the Canopy with two 30mm safety screws. The two safety screw holes are positioned on the back casing (refer to Pic 5).

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

After installation, make sure that the canopy is level to avoid grease collecting at one end.

Safety Warnings

• This Canopy is for domestic use only, it is not suitable for commercial purposes.
• Please ensure that installation is performed by a qualified competent installer.
• The Canopy and its filter mesh should be cleaned regularly in order to keep it in good working order.
• Before cleaning, please switch the power off at the main supply.
• Clean the Canopy according to the instruction manual. There is a fire risk if cleaning is not carried out in accordance with the instructions.
• If there is any fault with the appliance, please switch off immediately, disconnect and call the service department to arrange a service.
• DO NOT flambé under the canopy.
• CAUTION: Accessible parts may become hot when used with cooking appliances
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance. Never let the children operate the canopy.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Instructions for Use

Switch on the power to the Canopy.

1. Press power button, its indicator light will turn on, the hood works at low speed. Indicator light of low speed will be bright. Press power button again to close it, and its indicator light will be off. All the function operation of the hood will be closed, the hood enters into standby mode, and run by circle.
2. Press the Low Speed button, motor runs on low speed, the indicator light of low button and power button will beam. Press low button again and the motor will stop.
3. Push the middle button, the indicating light around the button will illuminate and the motor runs at mid speed. Push it again and the motor will stop and the light will switch off.
4. Push the high button, the indicating light around the button will illuminate and the motor runs at high speed. Push it again and the motor will stop and the light will switch off.
5. Push the light button; the indicating light around the button will illuminate and the two lighting lamps will switch on. Push it again and the lamps will switch off.

Maintenance

Cleaning the filters
The filters are made of stainless steel baffles. Please do not use corrosive or abrasive detergents to clean the filters. Keeping the filters clean will keep the appliance running correctly. Please strictly follow the guidelines below.

• Method 1: Put the baffle filter into a sink of clean water, pour on detergent, and soak for 2-3 minutes. Wear gloves and clean with a soft brush.
• Method 2: Wash in a dishwasher with the temperature set to around 60 degrees.

Cleaning the Canopy

1. To protect the main body from corrosion, the canopy should be cleaned with hot water plus non corrosive detergents every two months.
2. Please do not use abrasive detergent because it will damage the canopy.
3. Keep water away from motor and other electrical parts as this will cause damage to the appliance.
4. Before cleaning the appliance please remember to shut off the power and disconnect the plug.
5. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Troubleshooting

Warning: Service must be performed by an authorized competent person.

Light on, but motor does not work

| The flaps are blocked| Remove the blockage.
The capacitor is damaged| Call for service.
The motor is jammed due to bearing damage| Call for service.
There is a bad smell coming from the motor| Call for service.

Light does not work, motor does not work

| Beside the above mentioned, check the following:
Light damaged| Call for service.
Power cord not connected| Check plugged in and switched on that power is available.

Oil leakage

| Filters saturated with cooking oils.| Clean the filters.
Leakage between the connection of U-shaped section and canopy| Remove U-shaped section and seal
Vibrations| The flaps are damaged and

causes shaking

| Call for service.
The motor is not fixed

securely to the canopy body

| Call for service.
The canopy body is not fixed

securely to the wall

| Notify your installer.
Insufficient suction| The distance between the canopy and the cooking surface is too much| Notify your installer.
Too much ventilation from open doors or windows| Close doors or windows, choose an alternative location, if possible, away from draughts.
The Canopy inclines| The fixing screws are not tight enough| Notify your installer.
The hanging screws are not tight enough| Notify your installer.

Pronto Service + Support: 1800 440 335 Email: service@eurostylegroup.com.au

HEAD OFFICE
65 Glynburn Road, Glynde SA 5070
Ph: 08 8165 1012
www.euroappliances.com.au

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>