Sharkoon SHP V2 Power Supply User Manual
- June 3, 2024
- sharkoon
Table of Contents
SHP V2 Power Supply User
Manual
SHP V2 Power Supply
Dear Customer,
Thank you for your purchase of this high-quality SHARKOON product. To ensure a
long service life, and full functionality of the product, we recommend that
you read this manual thoroughly.
SHARKOON Technologies
www.sharkoon.com
General
| Power | 550 or 650 Watt |
|---|---|
| CPU | Compatible with the Latest Intel and AMD CPUs |
| PCIe Connectors | 2x 6+2-Pin PCIe Connector |
| Fan | 120 mm Fan |
| Efficiency | 20% Load: Min. 82% |
50% Load: Min. 85%
100% Load: Min. 82%
Specifications
2.1 Overview SHP550 V2
Model No.|
SHP550 V2
---|---
Input (AC)
| Input Voltage| Current|
Frequency
200-240 VAC| 4 A| 47-63 Hz
Output (DC)| +3.3 V| +5 V| +12 V| -12 V| +5 Vsb
Max. Output Current| 18 A| 18 A| 42 A| 0.3 A| 2.5 A
Max. Combined Power| 110 W| 504 W| 3.6 W| 12.5 W
Total Power| 550 Watt
2.2 Overview SHP650 V2
Model No.|
SHP650 V2
---|---
Input (AC)
| Input Voltage| Current|
Frequency
200-240 VAC| 5 A| 47-63 Hz
Output (DC)| +3.3 V| +5 V| +12 V| -12 V| +5 Vsb
Max. Output Current| 20 A| 20 A| 50 A| 0.3 A| 2.5 A
Max. Combined Power| 120 W| 600 W| 3.6 W| 12.5 W
Total Power| 650 Watt
2.3 Mains Voltage and Protections
This power supply works with 200-240 V. It is available with the following
protective measures:
- Over Power Protection (OPP) If a voltage rail draws in more electricity to the power supply than the specifications allow, the power supply will switch off.
- Over Voltage Protection (OVP) This function protects against excessive voltage, preventing damage to the PC by switching off the power supply during a surge.
- Short Circuit Protection (SCP) Should a short circuit occur with your PC, the SCP function switches off the power supply and protects the electronics from damage.
- Under Voltage Protection (UVP) Should the power supply fall below a fixed number for the minimum voltage it will switch off automatically.
2.4 Safety Certifications
Out power supply is tested and complies with CE and CB safety certifications.
Package Contents
A SHP550 V2/SHP550 V2
B Mounting screws
C Power cord
D Manual
Note:
If you are missing any of the items listed above, please contact our customer
service immediately:
support@sharkoon.com (Europe)
support@sharkoon.com.tw (International)
Cable Configuration
4.1 Connectors
4.2 Cable Length
Installation
If installing into an empty PC case please continue to section 5.1. If a power supply is already installed, remove it first from the case. To do so, proceed as follows:
- Turn off your PC. Disconnect the power cord from the wall outlet and your power supply.
- Open the PC case. For additional information, refer to the PC case’s manual.
- Disconnect all cables between the power supply and the other PC components (e.g. mainboard, HDDs, drives, fans, etc.).
- Remove the mounting screws connecting the power supply to the PC case and then carefully remove the power supply from the case.
5.1 Installing a Power Supply into a PC Case
-
Insert the power supply into the PC case and place it against the power supply bracket on the rear panel.
For additional information, refer to the PC case’s manual. -
Attach the power supply from the outside of the case using the provided screws. Ensure that the fan and air vents of the built-in power supply are not covered.
5.2 Connect the Mainboard and Graphics Card(s)
-
Plug the 20+4-pin mainboard connector (Fig. 1) into the respective port on the mainboard.
-
If your mainboard also features either a 4-pin or 4+4-pin CPU connector, connect the plug with the mainboard port (Fig. 2).
Note: The power connection of the mainboard depends on the vendor and may vary. For detailed information on how to establish the connector, please refer to your mainboard’s manual. -
If your PCIe graphics card requires an additional power supply, connected the 6-pin or 6+2-pin PCIe connector to ensure the graphics card receives a stable power supply.
5.3 Connecting Optical Drives and Other Peripheral Devices
- Connect the 4-pin IDE connector (Fig. 4), SATA connector (Fig. 5) and the 4-pin Floppy connector (Fig. 6) with the corresponding peripheral devices.
Note: For additional information, refer to the respective manuals of your drives and peripheral devices.
5.4 Checking All Connections
Ensure that all devices are properly connected. Close the PC case. Connect the
power cord with the power supply and wall outlet. Turn the power supply on.
This completes the installation of the power supply.
Note: All connectors are designed to avoid misconnection. If the
connectors are unable to connect to the mainboard, drives or peripheral
devices, please check if both connectors are attached in the correct
orientation. Do not force to plug the connectors within the incorrect
orientation, nor modify any of the components, as this will damage the power
supply and other hardware. SHARKOON warranty does not cover damage cause by
incorrect handling.
Troubleshooting
If the power supply does not work properly, please check the following:
- Is the power cord correctly inserted into a wall outlet and the power inlet of the power supply?
- Ensure that the on/off switch is in the “I” position.
- Check if the 20+4-pin mainboard connector and the 4+4-pin CPU connector are correctly attached to the mainboard.
- Check if the cable is securely connected to the port of the peripheral devices.
- Unplug the power cord from the wall outlet and let the power supply rest for about 10 minutes. This will trigger a reset of the protection circuitry.
If the system still does not start, please contact
support@sharkoon.com.
Legal Disclaimer: For potential loss of data, especially due to
inappropriate handling, SHARKOON assumes no liability. All named products and
descriptions are trademarks and/or registered trademarks of the respective
manufacturers and are accepted as protected. As a continuing policy of product
improvement at SHARKOON, the design and specifications are subject to change
without prior notice. National product specifications may vary. The legal
rights of the enclosed software belong to the respective owner. Please observe
the license terms of the manufacturer before using the software. All rights
reserved especially (also in extracts) for translation, reprinting,
reproduction by copying or other technical means. Infringements will lead to
compensation.
Disposal of your old product:
Your device has been designed and manufactured using high quality materials
and components that can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product, it means
the product is covered by the European Directive 2012/19/EU. Please be
informed about the local separate collection system for electrical and
electronic products. Please act according to your local rules and do not
dispose of your old products with your normal household waste. The correct
disposal of your old product will help prevent potential negative consequences
to the environment and human health.
SHARKOON Technologies GmbH
Siemensstraße 38
35440 Linden
Germany
© SHARKOON Technologies 2016
info@sharkoon.com
www.sharkoon.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>