AIYIMA D03 Bluetooth 5.0 2.0/2.1 Channel Amplifier User Manual

AIYIMA D03 Bluetooth 5.0 2.0/2.1 Channel Amplifier

Front Panel Introduction

1. Power
2. Input selection
3. Display
4. IR
5. Multifunction knob

Rear Panel Introduction

1. PC-USB input jack
2. Optical input jack
3. Coaxial input jack
4. Bluetooth antenna jack
5. RCA input jacks
6. Subwoofer output jack
7. Right speaker output jacks
8. Left speaker output jacks
9. DC Power Supply jack

Specifications

CHIPS| CS8422,TAS5548,TAS5624,
PCM1808,QCc3034…
---|---
Audio input
| PC-USB,Optical, Coaxial, RCA, BT

Bluetooth supports
| SBC,AAC, APTX,APTX-L, APTX-HD

PC-USB/Optical/Coaxial
Resolution/Sampling rate| Max 24bit/192kHz

PC-USB Operating System
| Windows 7/8/8.1 / 10 /MAC/Linux

**Frequency response
(Treble&Bass gain=0dB)

| +0db,-1.25dB @20-20kHz

TONE Gain ( Treble &Bass)
| t14dB

SNR
| 93dB

Subwoofer output level
| 2.1V

Output Power max
| 150Wx2@40 36v , 6% THD+N

Speaker impedance
| 4-8

Power Supply
| DC 24-36V

Dimensions (mm) / Weight(g)| 15137*141/690**

Product Question

1. The Amplifier board has current sound and noise.
   Most of our amplifier board use DC power supply. The board itself does not produce current sound and noise. The main causes of current acoustic noise are

   • The power supply filter used is not good; the current sound is caused by wrong input by the power or audio input.
   • The input signal quality is poor; the output of the device connected to the input is improper, and the noise is caused by the abnormal input of the audio source.
   • The input cable is of poor quality; the line is in poor connect; the wiring is damaged; the wiring is suspended
   • The input connection has other playback devices, and some devices share the power supply to cause noise.

2. No sound output, no sound in 1 channel

   • The speaker is broken, or the speaker cable is not connected well.
   • The input cable is not in good connect; the wiring is damaged; the output of the device connected to the input is improper.

3. Has volume broken and breaking sound when turn loud?

   • The power input is insufficient, confirm the wiring is correct first, and the supply Current is sufficient,
   • The speaker itself has poor performance or damage, and the speaker power is too small or too large.
   • left and right channel speakers (+) (-) output are independent, can not be connected to each other

4. Speaker broken sound when subwoofer amplifier volume turn loud?

   • The power input is insufficient, first confirm the wiring is correct, the supply current is enough
   • Whether the power of the speaker itself is too large or too small, or the bass performance of the speaker itself is poor; the structure of the speaker box; these abnormalities will cause breaks.

5. The volume power is not enough
   Power and power supply voltage, the amplitude of the sound source signal, the size of the speaker impedance are all related, any kind of deficiency will affect the power

6. Will the amplifier be burnt?

   • The positive and negative poles of the power supply are connected reversely; the power supply voltage is too high, exceeding the limit operating voltage of the board
   • If the board requires a DC power supply, it is not allowed to connect directly the AC transformer power supply (this can be rectified and converted to DC power before it can be used)
   • To confirm that the wiring is correct, then connect with the power supply. The wrong line connected or the short circuit both will cause damage to key parts!

Shenzhen Yima Technology Co.,Ltd

Website:www.aiyima.com

Email: sale@aiyima.com

Telephone: 86-0755-28268551 VK: https://vk.com/aiyima Location: 4F, Building 7 Hakan industrial park. Wuhe south road 41. Long-Gang district. ShenZhen. CHINA. 518000

References

• AIYIMA | AMPLIFIER & DECODER AUDIO
• VK.com | VK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>