AIYIMA T8 Bluetooth 5.0 Tube 6N3 Headphone Preamplifier User Manual
- June 6, 2024
- AIYIMA
Table of Contents
AIYIMA T8 Bluetooth 5.0 Tube 6N3 Headphone Preamplifier
Panel introduction
Parameter
Chip| SA9123L+ES9018+OPA1656+NJW1194
+QCC3031+6N3+MAX9722
PC-USB supports sampling rate| 192K
Distortion| RCA: 0.2%/HP: 0.003%
PC-USB support operating system| XP/W7/W8/W10/MAC/linux
Signal to noise ratio| RCA: 108dB/HP: 106dB
Headphone impedance| 16~300Ω
Operating Voltage| DC 12V
Maximum output power| RCA:1.9V/HP: 120mW@32Ω
Output sensitivity| 2V
Frequency response| 20Hz~20kHz(±0.5dB)
Operation steps
- Connect the audio source you need to use to the audio source input interface (switch the input channel to Bluetooth input when connecting bluetooth)
- Connect the back-end equipment that needs external connection to the audio source output interface (such as power amplifier，active speaker,etc.)
- Connect power supply (DC voltage shall not be higher than 12V)
- Press the encoder knob to start the machine.
- Short press the knob to switch to the corresponding input channel to be used.
- Turn the knob clockwise to select the desired volume.
PC-USB 0peration instructions
-
Connect the PC-USB interface to the computer with the USB cable configured by factory (USB supports hot plugging).
-
Press the encoder knob to switch to PC-USB input.
-
As shown in the figure, find the icon with horn symbol in the lower right corner of
-
Right click the pop-up dialog box and click (Playback devices)
-
Select the USB device recognized by PC from the pop-up dialog box (automatic IDENTIFICATION of NATIVE USB; manual installation of driver is not required ).
-
Click the recognized digital output and set it as the default.
Remote Instruction
Q & A
Q All my wires are connected_ Why Is there no sound?
- Check whether the machine is turned on and whether it has switched to the corresponding input channel.
- .Check whether the back-end connection is correct and whether the volume is in the minimum state.3. If all the above are normal, check whether the input playback device is silent, paused, or the volume is at its minimum.
Q Why can’t I search for bluetooth pairing names?
Due to the design of this machine,bluetooth does not work when using other
channels for input.You just need to switch the input to Bluetooth mode.
Q Why does the sound break?
Although this product is the front stage of DAC, it also has the function of
amplification. If the volume of the rear stage device is turned up to the
maximum, the volume of the front stageis also turned up to the maximum, which
is easy to distort. At this time, you just need to turndown the volume of the
front stage o r t he rear stage.
Q Why is there a lot of electrical noise from the horn?
If you are not using the original standard power supply, please replace the
power supply andtest again.Many power supply ripple interference factor is
large will cause a lot of current sound.
Q Why does the speaker make a loud buzzing sound when I plug in the input
cord and don’t playthe audio source?
when the signal line without shield is used,the interference signal will enter
the power amplifier for amplification. Replacing the signal line with shield
can effectively solve the interference sound.or unplug the signal line.
Warning!
- Do not open the shell without permission. Improper operation may damage the machine or cause electric shock.
- please use the regular manufacturer of switching power supply, otherwise there will be the risk of damage to the machine.
- Please do not change the vacuum tube at will, or it will burn out your vacuum tube or machine.
- Do not put the machine in a high temperature or humid environment.
FCC
This device complies with Part IS of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pan IS of the FCC Rules. These limits arc designed to provide reasonable prolection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance wiLh the instructions, may cause harmful interference to radio communications. However, there is no guarantee that in1erference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from chat to which the receiver is connected.
- Consult the dealer or an experienced radio t v technician for help.
NOTE: This device and its ante,rna(s) must not be co-located or operation in conjw1ction with any other antenna or transmitter
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be
installed and operated with minimum distance of 20cm the radiator your body.
This device and its antcnna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter
Shenzhen Yim a Technology Co.,Ltd
Website :www.aiyima.com
Email: sale@aiyima.com
Telephone: 86-0755-28268551
VK: https://vk.com/alylma
Location:
4F, Building 7 Hekan industrial park. Wuhe south road 41. Long-Gang district.
Shenzhen. CHINA. 518000
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>