JAR SYSTEMS CS-1610 Essential Charging Station Owner’s Manual
- June 3, 2024
- JAR SYSTEMS
Table of Contents
Charging Station
Owner’s Manual
Version F
CS-1610 Essential Charging Station
Disclaimer: Failure to read, thoroughly understand, and follow all
instructions can result in serious personal injury, damage to equipment, or
voiding of factory warranty. It is the installer’s responsibility to make sure
all mounting systems are properly assembled and installed using the
instructions provided. This information is the intellectual property of JAR
Systems LLC and may not be distributed, duplicated or copied in part or full
without the written permission. Since the use of this information, the
equipment connected and the conditions by which any JAR Systems product is
used is beyond the control of JAR Systems, it is the obligation of the owner
and/or user to determine the correct and safe use of any equipment and
product. To the extent that the law permits, any liability which may be
incurred as a result of the use or future use of a product manufactured or
sold by JAR Systems is limited to the cost of repairing or replacing the
failed product or component at the discretion of JAR Systems either within, or
outside of warranty periods, and does not extend to any loss or damage which
may be caused as a consequence of misuse or failure of the equipment or
product or the
information contained herein. JAR Systems shall not in any event be liable for
economic loss of profits, indirect, special, bodily injuries or consequential
damages. Specifications and images are for illustration purposes only. Final
product may differ and is subject to change without notice.
Before You Start: USB-C or AC?
Essential Charging Stations are available as USB-C and AC
configurations. Know which configuration you are assembling ahead of time. See
the parts list below for reference. Skip sections that are labeled (USB-C
stations only) or (AC stations only) if you are not assembling that
configuration.
Included:
Main Components
-
(1) Chassis
-
(1) T op Locking Bar
-
(1) T ray
-
ont Locking Arms
-
(2) Fr
(1) T25H Torx Key -
Stainless Steel Dividers (11 for CS-1210, 15 for CS-1610)
-
(1) Chassis Rubber Bumper
-
(1) Padlock with (2) Keys
-
(1) Power Strip (AC stations only)
-
(1) Quick-Sense USB-C Hub (USB-C stations only)
-
Right Angle Box Wrench (USB-C stations only)
-
(1) Power Cable (USB-C stations only)
Hardware Packet
A1. (11) Short Screws and Washers
B2. (8) Long Screws and Washers
C3. (4) Power Strip Screws with Nuts
D4. (4) Rubber Feet
E5. (4) Screws for Rubber Feet
F6. (4) Clear Cable Holder Clips
G7. 3 Sets of (4) Wall Mounting Screws
H8. Spar e Hardware
I9. Tools: Drill Bit
Assembling the Station
Prepare the Chassis
A. Remove contents of the carton and separate the major components. Use the
T25H Torx key that is packaged with the manual to remove the security screw
and washer from the center of the tray lid and set them aside to be replaced
at the end of assembly. (AC stations only) Remove the contents from the tray.
B. Extend the sides of the chassis out at right angles and tighten the pre-
installed screws on corner of each side. Each side has one on the top and one
on the bottom (4 screws total). CS-1210 only:
The CS-1210 right panel is detached for shipping. Attach with 2 [B2] screws
and washers.
C. The supplied rubber feet [D4], [E5] can be optionally installed in the four
holes on the bottom side of the station beside the holes used for securing the
station to a horizontal surface.
Secure Chassis to a Wall or Desk (Optional)
D. If the station will be used on a table, desk, or countertop, it may be
optionally secured to the surface by inserting 4 screws appropriate for the
surface type through the bottom side of the chassis.
E. T o mount the station to a wall, use the supplied template as a guide for
your screw location on the wall. Other tools helpful to mounting include a
level, stud finder, and a pencil to mark mounting points over studs in the
wall.
WARNING: Failure to provide adequate structural strength for this
mounting system can result in serious personal injury or damage to equipment.
It is the installer’s responsibility to make sure the structure to which this
mounting system is attached can support five times the combined weight of all
equipment. Reinforce the structure as required before installing. The wall to
which the mount is being attached may have a maximum drywall thickness of 5/8”
(1.6cm). Always ensure that proper hardware is used for the wall surface type.
Never operate this mounting system if it is damaged. Contact JAR Systems for
replacement or repair.
Install the Power Strip (AC stations only)
F. Install the power strip in one of the following positions with [C3] 4
screws and nuts.
- Recommended for smaller devices.
- Recommended for most desktop usage.
- Alter nate position for desktop usage.
- Recommended for most wall-mount usage.
- Alter nate position for wall-mount usage.
G. If necessary, the power strip can be mounted on either the front (position
1) or back (position #2) by reversing the mounting brackets. Loosen the three
screws on each side, rotate the bracket, and replace the screws.
Mount the Tray to the Chassis
H. Pull out the sides of the chassis to the depth needed for your device. If
the sides will not slide out easily, loosen the pre-installed screws on the
sides. Note: To prevent unauthorized removal of devices, do not extend the
sides further than needed to fit the devices.
I. Rest the tray on the tabs near the front of the chassis. Insert 3 [B2]
screws with plastic washers through the chassis and into the tray on each side
of the station.
Install Rubber Bumper (Optional)
J. To protect your devices from hitting the back edge of the chassis, utilize
the supplied rubber bumper.
Install the Top Security Bar (Optional)
K. For security, place the top locking bar at the lowest height that will fit
over the devices. Use 2 [B2] screws on the top two holes on the outside. Open
the tray lid and prop it up by placing a security screw or the Torx wrench in
the side of the station.
Install 1 [A1] screw from the inside of the chassis to prevent removal, on
both sides.
Insert the Dividers into the Tray
L. Remove the pre-installed divider locks from under the shelf. Insert the
dividers into the slots on the shelf. Ensure that all dividers are properly
seated and re-install the divider locks beneath the shelf using 6 [A1] screws.
Install the Front Locking Arms (Optional)
M. For security, install the front locking arms using 2 [A1] screws on each
side. Screws for the locking arms should be installed from the inside of the
chassis to prevent removal.
N. Use the included padlock to secure the station by looping it through the
holes in the arms. Using the padlock in the “upside down” position may be
easier for some users. This step completes the setup for USB-C configurations.
Cable Management (AC stations only)
O. Open the tray lid and prop it up by placing a security screw or the Torx
wrench in the side of the station.
P. Deter mine the length of cable that is needed to reach from the tray to the
devices.
Q. Deter mine the best method of arranging the cables that come with your
device.
AC ADAPTERS FRONT TO BACK: Best for some wider adapters. AC ADAPTERS LEFT TO
RIGHT: Best for some narrower adapters.
TABLET (NO AC ADAPTER): Use
provided clips [F6] beneath shelf to secure cables in groups of 5-6.
TIP: Adapters can often be installed as they come bundled in the box. If the
cables are not bundled at all, twist ties or Velcro ties are helpful. If the
devices have larger AC adapters (5”x 2”x 1.25” or larger) the adapters will
fit snugly in the tray.
In this case it may be best to arrange most of the adapters as far back in the
tray as possible from left to right, flipping about half on their side.
Contact JAR Systems for additional assistance.
R. After AC adapters are arranged in the tray, plug them into the power strip.
For best results, bundle any excess cable length if it is not already.
S. (OPTIONAL) Secure the tray lid shut using the security screw and washer
that were removed in step A and the Torx key to prevent adapters from being
removed or tampered with. This step completes the setup for AC configurations.
Want to skip this cable management process? CS-1610 and CS-1210 AC charging
stations can be upgraded to Quick-Sense USB-C charging. Contact JAR Systems
for more information: 866.393.4202 JAR-Systems.com
Warnings
Exceeding the weight capacity can result in serious personal injury or damage
to equipment. It is the installer’s responsibility to make sure the combined
weight of all components attached to this mount does not exceed 100 lbs.
If the station is being used or transported on an AV cart or charging cart,
the station must be secured down to the cart.
Power down all devices prior to connecting them to the Quick-Sense USB-C Hub
for charging.
Keep away from moisture and harsh chemicals. Do not place any liquids near the
station.
Any electrical equipment must be used by an adult or with adult supervision.
Do not connect unsupported items to the charging station or use for any
purpose other than intended.
Do not attempt to obstruct any ventilation openings or dismantle, open, or
modify the system in any way.
Do not sit or stand on the station or Quick-Sense USB-C Hub.
Do not use an extension cable or daisy-chain to any other devices.
The Quick-Sense USB-C Hub is not intended for operation at altitudes greater
than 2000 m or 6561 ft above sea level and should not be operated in extreme
temperatures. For indoor use only.
Disclaimer Failure to read, thoroughly understand, and follow all instructions
can result in serious personal injury, damage to equipment, or voiding of
factory warranty.
Since the use of this information, the equipment connected, and the conditions
by which any JAR Systems product is used is beyond the control of JAR Systems,
it is the obligation of the owner and/ or user to determine the correct and
safe use of any equipment and product. To the extent that the law permits, any
liability which may be incurred as a result of the use or future use of a
product manufactured or sold by JAR Systems is limited to the cost of
repairing or replacing the failed product or component at the discretion of
JAR Systems either within, or outside of warranty periods, and does not extend
to any loss or damage which may be caused as a consequence of misuse or
failure of the equipment, product or the information contained herein. JAR
Systems shall not in any event be liable for economic loss of profits,
indirect, special, bodily injuries or consequential damages. Specifications
and images are for illustration purposes only. Final product may differ and is
subject to change without notice.
Warranty
This product comes with a warranty that covers any defects in material or
workmanship and extends to the original consumer of the product only. JAR
Systems, LLC will replace the product with a new or refurbished product,
repair the product, send replacement parts, or refund the purchase price of
the product, at JAR Systems, LLC’s discretion. This warranty does not cover
accidental damage, unreasonable use, neglect, tampering or other causes not
arising from defects in material or workmanship. Any implied warranties last
only as long as the warranty periods listed above except where state law does
not allow limitations on how long an implied warranty lasts. This includes but
is not limited to the implied warranties or merchantability and fitness. JAR
Systems, LLC’s responsibility is limited to the actions listed above and
nothing else.
This warranty does not cover, and JAR Systems, LLC will not be responsible
for, any damages due to loss of use of the product, or any other costs or
expenses incurred by you or anyone else who uses the product, whether due to
defects, breach of contract, negligence, strict liability or otherwise. JAR
Systems is not liable for any indirect, special, incidental or consequential
damages related to the product or this warranty. Some states do not allow
exclusions or limitations on consequential or incidental damages,
so these limitations or exclusions may not apply. This warranty gives you
specific legal rights and you may also have other rights that vary from state
to state. This warranty is governed by the laws of Florida, excluding its
conflict of laws principles, unless your state requires that its law be used.
Contact JAR Systems for information on the length of
warranty on your product(s).
References
- JAR Systems: Charging and Managing Devices Made Simple
- JAR Systems: Charging and Managing Devices Made Simple
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>