JAR SYSTEMS MC-7036-MX Elevate Max USB-C Charging Cart User Guide
- June 9, 2024
- JAR SYSTEMS
Table of Contents
USB-C Charging Cart
MC-7036-MAX User Guide
Quick Start
- Connect cart to power source
- Plug in powered down devices
- Connected devices will automatically charge as efficiently as possible
- Connect/disconnect devices any time
LED Charging Port Indicator Lights
Normal Operation
-
Plug the power cable into a standard 15A outlet. Be sure that the power switch on the side of the cart is in the ON position. LEDs will illuminate white to indicate the cart is connected to a power source.
-
Power off devices fully before connecting them to the cart for charging.
-
Connect the devices to the USB-C charging cables.
Ensure that devices are placed in the cart so that the charging ports are as close as possible to the USB-C charging port on the cart. Incorrectly connecting devices can strain the cable over long periods of time and lead to damage. -
You may hear a clicking sound, and the LED lights will change color according to the power draw of the attached devices.
-
The system will automatically limit power consumption by turning some of the USB-C ports off temporarily. Refer to the device for the level of charge. Connected devices will charge as fast and evenly as possible, up to 65W, without drawing too much power. To remove devices from the carts with the greatest level of charge first, disconnect devices with the green LEDs first before you disconnect devices with the blue LEDs.
Devices that do not feature a USB-C charging port can be charged using USB-C emulator cables.
(Not Included, contact JAR Systems for more info)
Trouble-Shooting
Always start troubleshooting with a simple reboot Unplug and replug the power
cord. When the cart is connected to power, the LEDs will change color based on
the power draw of connected devices (see light indication).
Single Port or Device Issue
Ensure that both of the USB-C cable ends plug into the cart and the device
correctly.
If there is still no charge, disconnect the device from that port (A) and plug
into another port (B). If it is still not charging, it may be an issue with
the device.
If charging begins when using port (B), exchange the cable from port (B) to
port (A). If it begins to charge, the cable (A) is defective and will need to
be replaced.
Entire Charging Hub/Shelf Issue
Check the side of the charging hub on the left side of the cart to see if the
cart’s power cable is plugged in and connected correctly.
When the cart is powered back on, the LED lights will begin to illuminate.
Remove/Replace
USB-C Cables
Each cable lock may be secured with up to three screws. Remove all screws with
the supplied Torx key.
Remove the cable lock. Unplug the cables from the USB-C ports and route them
through the cable track.
Reverse the process to replace a cable.
Adjusting Device Bay Dividers
Elevate carts feature adjustable device bays with multiple configuration
options. Use the guides below to determine which hole pattern to use.
To remove dividers, push in and upward on the front of the divider and guide
it out of the slot in the tray. To install the dividers, simply place the tall
side of the divider into the rear slot first, then push in and downward to get
the other side into the front slot.
36 DEVICE PATTERN
Best for devices up to 1” wide.| 30 DEVICE PATTERN
Best for devices up to 1.25” wide.| 24 DEVICE PATTERN
Best for devices up to 1.5” wide.
---|---|---
| |
Warnings
- Power down all devices prior to connecting them to the hub for charging.
- Keep away from moisture and harsh chemicals. Do not place any liquids near the charging cart.
- Any electrical equipment must be used by an adult or with adult supervision.
- Do not connect unsupported items to the charging cart or use for any purpose other than its intended use.
- Do not attempt to obstruct any ventilation openings or dismantle, open, or modify the system in any way.
- Do not sit or stand on the cart or charging hubs.
- Do not use an extension cable or daisy-chain to any other devices.
- Not intended for operation at altitudes greater than 2000 m or 6561 ft above sea level and should not be operated in extreme temperatures. For indoor use only.
Disclaimer
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty. Since the use of this information, the equipment connected, and the conditions by which any JAR Systems product is used is beyond the control of JAR Systems, it is the obligation of the owner and/or user to determine the correct and safe use of any equipment and product. To the extent that the law permits, any liability which may be incurred as a result of the use or future use of a product manufactured or sold by JAR Systems is limited to the cost of repairing or replacing the failed product or component at the discretion of JAR Systems either within, or outside of warranty periods, and does not extend to any loss or damage which may be caused as a consequence of misuse or failure of the equipment, product or the information contained herein. JAR Systems shall not in any event be liable for economic loss of profits, indirect, special, bodily injuries or consequential damages. Specifications and images are for illustration purposes only. Final product may differ and is subject to change without notice.
Warranty
This product comes with a warranty that covers any defects in material or
workmanship and extends to the original consumer of the product only. JAR
Systems, LLC will replace the product with a new or refurbished product,
repair the product, send replacement parts, or refund the purchase price of
the product, at JAR Systems, LLC’s discretion.
This warranty does not cover accidental damage, unreasonable use, neglect,
tampering or other causes not arising from defects in material or workmanship.
Any implied warranties last only as long as the warranty periods listed above
except where state law does not allow limitations on how long an implied
warranty lasts. This includes but is not limited to the implied warranties or
merchantability and fitness.
JAR Systems, LLC’s responsibility is limited to the actions listed above and
nothing else.
This warranty does not cover, and JAR Systems, LLC will not be responsible
for, any damages due to loss of use of the product, or any other costs or
expenses incurred by you or anyone else who uses the product, whether due to
defects, breach of contract, negligence, strict liability or otherwise. JAR
Systems is not liable for any indirect, special, incidental or consequential
damages related to the product or this warranty.
Some states do not allow exclusions or limitations on consequential or
incidental damages, so these limitations or exclusions may not apply.
This warranty gives you specific legal rights and you may also have other
rights that vary from state to state. This warranty is governed by the laws of
Florida, excluding its conflict of laws principles, unless your state requires
that its law be used.
Contact JAR Systems for information on the length of warranty on your
product(s).
Explore more options for USB-C Charging!
Learn about ways to charge devices in growing technology landscapes. Contact a
JAR Systems representative at 866.393.4202 or visit: JAR-
Systems.com/Products
Version A
M00017
Last Modified 03/28/2023
For a copy of the most up-to-date manual, please contact a
JAR Systems representative or visit: JAR-Systems.com/Support
Designed in the USA
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>