FOSCAM SD2X Wireless PTZ Dome IP Camera User Guide
- June 4, 2024
- FOSCAM
Table of Contents
FOSCAM SD2X Wireless PTZ Dome IP Camera
Getting Started
Package Contents
Security Tips
Please change the camera’s password regularly, using a combination of
numbers, letters and special characters.
We recommend that you regularly update your camera with the latest available
software and firmware to ensure the best experience with your camera.
Physical Description
The cords on this produc t are a potential strangulation hazard. For child safety, please keep these cords out of the reach of children.
Wired Connection via the Foscam App (Recommended)
Before You Get Started
Scan the QR code below to download and install the Foscam APP.
To ensure a smoother video experience on your smart phone, it is recommended that your smart phone meet the following specifications:
iOS: version 8.1 or higher.
Android: 4.1 or higher, using a device with a Graphics Processing Unit (GPU).
Note: For the best experience, please update the APP to the latest version!
Wired Connection
-
Please tighten the antenna clockwise and make sure it is in a vertical position.
-
Connect the camera to your router with an Ethernet cable.
-
Plug the power adapter into the camera, and then wait for about 1 minute.
-
Make sure your smart phone is connected to the same WiFi network as the camera.
Tips: The camera supports dual-band 2.4GHz and 5GHz WiFi networks, so you can choose the channel with the stronger signal to use. For example, choose your SSID: XXXXX_2.4G or XXXXX_5G. -
Open the foscam APP and please register a Foscam account, or sign in if you have one already.
-
After logging into Foscam APP, select “Tap to add a camera” or “+” icon on the upper right corner, then select “Scan the QR code” and scan the QR code that labeled at the bottom of your camera.
-
There are two options in the following steps, please pay attention to choose the corresponding adding method.
-
Please wait for a few seconds, you can tap “Configure WiFi” in “Configure WiFi” interface, then select your WiFi network and enter your WiFi’s password. After, you can set the camera name and tap “Save” in “Set name” interface.
Note: It is strongly recommended that you choose to configure WiFi at this step. -
Please wait for a few seconds, you can tap “Configure WiFi” in “Configure WiFi” interface, then you tap “Skip” in the “WiFi Settings” interface. After, you can set the camera name and tap “Save” in “Set name” interface.
Note: If the adding process fails, please reset your camera and try adding again according to the above method. -
Tapping on the play button in the video box will jump to the “Camera Login” setting interface. For your security, please set a new username and password for your camera before viewing live video.
-
After completing the above steps, you can begin using your camera.
Note: If you choose installation step 7.2, please refer to the following steps for configuring WiFi . After setting your WIFi, you can unplug your network cable and the camera works normally.
Configure WiFi
If you selected “Skip” in step 7, click play to enter the camera credentials
interface > Tap the “ ” button > tap “WiFi Settings” > select your WiFi
network and enter your WiFi’s password. After setting up successfully, you can
view live video without the Ethernet cable.
Other Ways to Access Your Camera
Foscam VMS
Foscam VMS is a new tool for PCs. It does not require plug-ins and is
compatible with Windows & Mac, supporting all Foscam HD cameras and up to 36
cameras at the same time. If you would like to manage multiple cameras, we
suggest you install Foscam VMS. You can download the “Foscam VMS ” Windows
version from foscam.com/vms, and can download the “Foscam VMS” Mac version
from the APP store:
https://apps.apple.com/cn/app/foscamvms/id1521202507?mt=12
Note : For the best experience, please update Foscam VMS to the latest version!
Add the IP Camera
- Run Foscam VMS, then create a local administrator account and login.
- Tap the “+” icon on the Foscam VMS and follow the setup wizard to add your camera.
Please visit foscam.com/downloads to view the user manual and for additional detailed steps.
Foscam Cloud Service
You can access the camera via the Foscam Cloud website:
https://www.myfoscam.com
Some benefits of viewing your camera in the cloud:
It’s simple and convenient to remotely access and manage all your WiFi
security cameras.
Enjoy the latest features first through Foscam Cloud including cloud storage
and more.
Getting started is fast—if you have already registered an account in the
Foscam App, you can directly use the same login credentials for Foscam Cloud.
Hardware Installation
Fixate the camera on your preferred location and use the provided screws to mount it.
Please Note:
Ensure that the rain or water will not reach the connector ports at the end of
the pig tail wiring. These connectors are not weather-resistant.
Important Notice
Camera Username & Password
The camera username & password are used to access and manage your camera.
Having a strong password can significantly improve the security of your
camera.
If you have forgotten either of them, please press the “Reset” button and hold
it for more than 10 seconds while the camera is powered on. After release the
button. The camera will automatically reboot and the default settings will be
restored.
You can then reconnect the camera by following this Quick Setup Guide.
Foscam Cloud Service Account Username & Password
Your Foscam Cloud service account and password may be used to access both the
Foscam App and the Foscam Cloud service website. Therefore, you can register
your account username & password on either one.
Storage Media
Your camera supports cloud, NVR (Network Video Recorder), and Micro SD card
(only supports FAT-32 format) storage formats. If you wish to record and play
back large amounts of video, we recommend using a Foscam NVR device as well.
Firmware Upgrade
You can upgrade the firmware of your camera with the Foscam App by using the
new “One-Key Online Upgrade” feature (Open the Foscam App and Login to the
camera, select Settings > Firmware Upgrade).
You also can download the latest version to upgrade your camera from our
official website foscam.com/upgrades.
Safety Tips
- Please ensure that the proper power supply is used before using the camera.
- Please install the camera securely using the screws provided.
- Please use this product within the temperature range. When the ambient temperature is too high or too low, it may cause product failure.
- To avoid the risk of fre fire or electric shock, please keep your camera connectors in a cool, dry place.
- Please keep the camera out of reach of small children.
- This product is not a toy; children should use the product under under adult supervision.
- Change your default port to a greater range to help ensure the safety of your connection. How to change the default port: please visit foscam.com/downloads to view the
- user manual.
- Check the logs of your Foscam cameras frequently. Foscam Foscam Cameras have embedded logs reminding telling you which IP addresses addresses are accessing the camera.
Product Performance
WLAN frequency range: 2412MHz – 2472MHz and 5725MHz – 5875MHz Maximum
transmission power: < 18.5dBm
Wireless Standard: IEEE802.11b/g/n (2.4GHz)
IEEE802.11a/n/ac (5GHz)
Power Supply: DC 12V 2.0A 24W
Technical Support
If you have problems with your Foscam device, please contact the the reseller
you purchased from, or you can e-mail the headquarter company headquarters
technical support team: support@foscam.com
Your valuable comments and suggestions on improving Foscam products are
welcomed!
References
- Foscam Support - FAQs
- Foscam Support - FAQs
- Foscam Official Website - Security Cameras, NVRs, Baby Monitors, IP Cameras, NVR Kits, Security Kit, Pet Monitors, Cloud Storage Service
- Foscam Open-Information System
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>