Electrolux EIFH/C-2 EEC EIFH/C-3 EEC PTC Heater User Manual

June 3, 2024
Electrolux

ELECTROLUX LOGO

Electrolux EIFH/C-2 EEC EIFH/C-3 EEC PTC Heater

WE THINK ABOUT YOU
Thank you for purchasing an Electrolux appliance. You have chosen a product, backed by decades of professional experience and innovations. Unique and stylish, it was created with care for you. Therefore, whenever you use it, you can be sure that the results will always be excellent. Welcome to Electrolux!

On our website you can:
Find product recommendations, user manuals, maintenance information: http://www.home-comfort.com/support/

Buy a product in your city:http://www.home- comfort.com/search/find-a-store/
While selling this device, dealer must fill “Product details” section located on the inside of the back cover of this manual.

Designation

  • Caution/Important safety information
  • Common information and recommendations
  • Warranty service is performed according to the terms specified in the uwarranty” section.
    Note: In the text of this manual, the fan heater may have such technical names as appliance, device, vehicle etc. This product is only suitable for well insulated spaces or occasional use.

Introduction

Please read and strictly follow the requirements contained in this manual. Please keep the manual and documents confirming the date of purchase of the device in a safe place for easy retrieval and use. The device is intended for air heating in household premises.

Safety regulations

When using the device, observe the general safety rules for using electrical devices. Failure to follow the safety instructions and instructions can result in electric shock, fire and/ or serious injury.

Before using the appliance, please read the following safety precautions carefully:

  • Make sure that the power supply corresponds to that indicated on the label of the appliance.
  • It is forbidden to use the device in rooms: with relative humidity over 93%, with explosive atmosphere; with a biologically active environment; highly dusty environment; with environments that are corrosive to materials. It is forbidden to operate the device if you come into contact with water.
  • Do not use an appliance with a damaged and/or damaged or frayed power coble. Arcing or repeated tripping of the thermal fuse indicates a malfunction of the device.
  • Do not attempt to disassemble, repair or modify the device yourself. Doing so could result in fire or electric shock.
  • Do not use this apparatus near o both, shower or any other container with water. It is forbidden to operate the device if you come into contact with water.
  • Before moving, maintaining, cleaning the appliance, or if it is turned off for an extended period, disconnect it from the mains and let it cool down.
  • The mains cable must be positioned so that it is not stepped on, that it is not abraded, torn, kinked or otherwise damaged. The grill temperature may be too high during operation.
  • Beware of touching it to avoid burns.

Design of the applianceElectrolux EIFH-C-2 EEC EIFH-C-3 EEC PTC Heater
1

  1. Heating element
  2. Air outlet grille
  3. Carrying handle
  4. Device body
  5. Support leg
  6. Air intake grille
  7. Axial fan
  8. On/ Off button
  9. Thermostat knob

The body (4) of the fan heater is made of sheet steel covered with a high- quality polymer coating. The body is mounted on a support leg (5). A fan (7) and a highly efficient sintered metal heating element (1) are located inside the body.

Preparation to the work

Unpack the device and its components from the packaging. Insert the carrying handle (3) into the two holes on top of the fan heater. Insert 2 screws into the screw holes of the air outlet (2) and air inlet (6) grilles and screw the carrying handle (3). Next, insert the support leg (5) with the grooves into the holes in the base of the fan heater and snap into place. If necessary, screw the support leg (5) to the cannon body with two screws through the special holes in the support leg (5).

Technical data

The fan heater can operate in one of two modes:

  • Heating mode;
  • Ventilation mode without heating.

The fan heater has built-in overheating protection. When the body of the electric heater overheats, an automatic thermal fuse turns off the fan heater, eliminating the possibility of a fire and failure of the product itself.

Overheating of the case can come from the following reasons:
The openings in the housing at the air inlet and outlet are blocked by foreign objects or heavily soiled; Uncorrected fan heater; The heat output of the fan heater is much higher than the heat loss of the room in which it operates.

Specifications

Model EIFH/C-2 EEC EIFH/C-3 EEC
Supply voltage, V ~ Hz 220–240 ~ 50 220–240 ~ 50
Maximum power consumption, kW * 2.2 3
Productivity, m3/h 100 150
Rated current, A 9.6 13.6
Protection degree IP 21 IP 21
Electrical protection class I class I class
Heating area, m2* up to 25 up to 35
Appliance size (W×H×D), mm 150×180×170 175×205×180
Packing size (W×H×D), mm 180×150×160 195×175×185
Net weight, kg 1.1 1.6
Gross weight, kg 1.2 1.7

Indicated is a guideline value and may differ depending on actual conditions of use.

Appliance operation
When using the device, observe the safety requirements outlined in this manual. Before turning on the fan heater, the switch key must be in position “2”, and the thermostat knob must be turned to the extreme counterclockwise position.

Fan heater control panel

Electrolux EIFH-C-2 EEC EIFH-C-3 EEC PTC
Heater 2

  1. Mode “1”, on (air heating and, depending on the position of the thermostat, ventilation without heating)
  2. Mode “0” (off).
  3. Thermostat

Turning on the fan heater and operating modes

To turn on the fan heater, connect the mains plug to the mains socket, set the switch button to position “1” (mode “1”). If the ambient temperature is higher than the one set by the thermostat, the fan heater works in ventilation mode without heating. If the ambient temperature is lower than that set by the thermostat, the fan heater operates in the ventilation mode with heating. The thermostat knob sets the required air temperature in the room. The thermostat maintains the set temperature by automatically turning off and on the electric heater (the approximate range of the maintained temperature is from 0 to +40 °C). To increase the desired temperature, turn the thermostat knob clockwise, to decrease – counterclockwise.

Comfort mode
To set the required heating temperature and maintain a constant room air temperature, turn on the appliance at full power by moving the thermostat control knob to the “max” position. When the room temperature reaches a comfortable level for you, slowly turn the thermostat control knob counterclockwise until you hear a click. Thus, the device will remember the temperature that is comfortable for you and will maintain it by automatically switching on and off.

Transportation and storage
The device in the manufacturer’s packaging can be transported by all types of covered transport with the exception of shocks and movements inside the vehicle. The device should be stored in the manufacturer’s packaging in a heated, ventilated room at a temperature of +5 °C to +40 °C and an average monthly relative humidity of 65% (at a temperature of +25 °C).
WARNING : After transportation at subzero temperatures, it is necessary to keep the fan heater in the room where it is supposed to be used without being connected to the network for at least 2 hours.

Completing units

  • Fan heater;
  • Handle;
  • Support leg with latches;
  • Screw (4 pieces);
  • Operation manual;
  • Warranty card;
  • Packing.

Recycling
The time-expired appliance can’t be disposed with household waste (2012/19/EU).

Warranty

Warranty service is performed according to the terms specified in the “Warranty” section.

Warranty:

  • Warranty period for the item is two years from the purchase date. If any defects occur due to defects in materials and/or workmanship during this two-year warranty period, the item should be repaired or replaced.
  • Free maintenance or replacement is possible only in case if convincing evidence is provided, for example a stub, which confirms that the day when the service is requested, is within the warranty period.
  • The warranty does not cover products and/or parts of the product that are subjects to deterioration, may be considered as expendable supplies or which are made of glass.
  • The warranty is void if the defect is caused by damage ensuing by misuse, poor maintenance (for example, a failure occurred due to ingress of foreign objects or liquids) or if changes or repairs were performed by persons not authorized by the Manufacturer.
  • For the correct use of the product, the user must strictly follow all included in the manual instructions, and also must avoid any action or manipulation described as unwanted or indicated so in this manual.
  • These warranty restrictions do not affect your statutory rights.

Support:
The support during and after the warranty period is available in all countries where the product is officially distributed. Please contact your dealer for help.

Date of manufacture
The date of manufacture is indicated on a sticker on the body of the appliance, and also encrypted in Code-128. The date of manufacture is determined as follows:

Electrolux EIFH-C-2 EEC EIFH-C-3 EEC PTC Heater 3

Do not remove and keep safe the serial number on the device’s body. If the serial number sticker is lost or damaged, it will not be possible to restore the production date if necessary.

Manufacturer : CladSwiss AG,
Bahnhofstrasse 27, 6300 Zug, Switzerland.
E-mail:info@cladswiss.com

Made in PRC

Electrolux is a registered trademark used under license from AB Electrolux (publ.). The manufacturer reserves the right to modify the design and characteristics of the device. This manual may contain technical and typing errors. Changes to technical characteristics and assortment are subject to change without notice. Mistakes and typing errors may be permitted in texts and numeric notations. Product design and technical data may vary from the one pictured on the packaging. Please refer to a sales consultant for more detailed information. http://www.home-comfort.com

Information requirment for thе electric local space heaters

Model identifier(s): EIFH/C-2 EEC
ltem| Symbol| Value| Unit| Item| Unit
Heat output| Туре of heat input, for electric storage local space heat- ers only (select one)
Nominal heat output| Pnom| 2.1| kW| manual heat charge control, with inte- grated thermostat| YES
Minimum heat output (indica- tive)|

Pmin

|

2.1

|

kW

| manual heat charge control with room and/or outdoor temperature feedback|

NO

Maximum con- tinuous heat output|

Pmax,c

|

2.1

|

kW

| electronic heat charge control with room and/or outdoor

temperature feedback

|

NO

Auxiliary electricity consumption| fan assisted heat output| NO
At nominal heat output| elmax| N/A| kW| Туре of heat output/room temperature control (select one)
At minimum heat output| elmin| N/A| kW| single stage heat output and nо room temperature control| NO
ln standby mode| elSB| N/A| kW| two оr more manual stages, nо room tem- perature control| NO
| | | | with mechanic thermostat room tempera- ture control| YES
| | | | with electronic room temperature control| NO
| | | | electronic room temperature control plus day timer| NO
| | | | electronic room temperature control plus week timer| NO
| | | | Other control options (multiple selections possible)
| | | | room temperature control, with presence detection| NO
| | | | room temperature control, with open win- dow detection| NO
| | | | with distance control option| NO
| | | | with adaptive start control| NO
| | | | with working time limitation| NO
| | | | with blасk bulb sensor| NO
Contact details| Manufacturer: CladSwiss AG, Bahnhofstrasse 27, 6300 Zug, Switzerland. E-mail: info@cladswiss.com
Information requirment for thе electric local space heaters

Model identifier(s): EIFH/C-3 EEC
ltem| Symbol| Value| Unit| Item| Unit
Heat output| Туре of heat input, for electric storage local space heat- ers only (select one)
Nominal heat output| Pnom| 3.0| kW| manual heat charge control, with inte- grated thermostat| YES
Minimum heat output (indica- tive)|

Pmin

|

3.0

|

kW

| manual heat charge control with room and/or outdoor temperature feedback|

NO

Maximum con- tinuous heat output|

Pmax,c

|

3.0

|

kW

| electronic heat charge control with room and/or outdoor

temperature feedback

|

NO

Auxiliary electricity consumption| fan assisted heat output| NO
At nominal heat output| elmax| N/A| kW| Туре of heat output/room temperature control (select one)
At minimum heat output| elmin| N/A| kW| single stage heat output and nо room temperature control| NO
ln standby mode| elSB| N/A| kW| two оr more manual stages, nо room tem- perature control| NO
| | | | with mechanic thermostat room tempera- ture control| YES
| | | | with electronic room temperature control| NO
| | | | electronic room temperature control plus day timer| NO
| | | | electronic room temperature control plus week timer| NO
| | | | Other control options (multiple selections possible)
| | | | room temperature control, with presence detection| NO
| | | | room temperature control, with open win- dow detection| NO
| | | | with distance control option| NO
| | | | with adaptive start control| NO
| | | | with working time limitation| NO
| | | | with blасk bulb sensor| NO
Contact details| Manufacturer: CladSwiss AG, Bahnhofstrasse 27, 6300 Zug, Switzerland. E-mail: info@cladswiss.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals