beamZ SB400 Stage Blinder User Guide

June 3, 2024
beamZ

beamZ SB400 Stage Blinder top

150.450 V1.2

SB400

QUICK START GUIDE

CONTROL MENU
MENU DESCRIPTION
DMX d001-d512
AUTO RUN Au01 – Au07
Au08 – Au10 LED Running effect
S01 – So02 Sound-controlled strobe effect
STROBE St01- St16
SPEED SP00 – SP16
WHITE u000 – u255
DMX CHANNELS
CHANNEL FUNCTION VALUE DESCRIPTION
1 Dimmer 000-255 Master dimmer 0-100%
2 Strobe 000-001 No function
002-255 Strobe
3 Macro 000-050 No function
051-200 Macro function
201-255 No function
4 Macro speed 000-255 Macro function speed adjustable
5 LED 000-255 LED 1 Dimmer 0-100%
6 000-255 LED 2 Dimmer 0-100%
7 000-255 LED 3 Dimmer 0-100%
8 000-255 LED 4 Dimmer 0-100%

    beamZ SB400 Stage Blinder A02

  1. SAFETY CABLE
  2. TRUSS CLAMP
TROUBLE SHOOTING

The checklist below may help you troubleshoot in the unlikely event that a problem occurs while using the product:

SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION
No response from unit. No power to unit.

Fuse blown or internal fault.

| Check that power is turned on.
Check cables and connections.
Replace mean fuse or contact Beamz support or Beamz authorized service partner. Do not remove base or yoke covers. Do not attempt to replace a fuse or carry out any repairs or service that are not described in this User Manual unless you have both authorization from Beamz support or Beamz authorized service partner.
Unit resets correctly but does not respond (or does not respond correctly) to the controller.| The controller is not connected.

Bad DMX-line.

DMX-line has no end resistance.

Incorrect unit addressing.

A unit is defective and is disturbing data transmission on the DMX-line.

Pin 2 and 3 are reversed in XLR connection.

| Connect controller.
Inspect connections and cables. Correct poor connections. Repair or replace damaged cables.
Insert DMX terminator plug in DMX output socket of last unit on DMX-line.
Check unit address and DMX mode settings.
Unplug DMX IN and OUT connectors and connect them directly together to bypass one unit at a time until normal operation is regained.
Have defective unit serviced by an authorized technician.
Inspect connections and cables. Install a phasereversing cable between the units or swap pin 2 and 3 in the unit, that behaves erratically.
Error after unit reset.| Effect requires mechanical adjustment.| Check unit’s software version and error messages for more information. Contact Beamz support or Beamz authorized service partner.
Light output cuts out intermittently.| Unit too hot.

LEDs damaged

The power supply settings do not match local AC voltage and frequency.

| Allow unit to cool. Reduce ambient temperature. Ensure free airflow around unit. Clean unit if necessary.
Disconnect unit and contact Beamz support or Beamz authorized service partner.
Disconnect unit. Check settings and correct if necessary.

beamZ SB400 Stage Blinder bottom

is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operated DMX effects, static washes, sound-activated club effects, strobes & blacklights, LED lighting, Fog and special effects machines, lasers and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags.

BEAMZLIGHTING.COM

Documents / Resources

| beamZ SB400 Stage Blinder [pdf] User Guide
SB400 Stage Blinder, SB400, Stage Blinder, Blinder
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals