ANGEL ELECTRONICS 2AZCXSLEEPHALO Sleephalo Wireless Phone Charger User Manual
- June 6, 2024
- ANGEL ELECTRONICS
Table of Contents
ANGEL ELECTRONICS 2AZCXSLEEPHALO Sleephalo Wireless Phone Charger
User Manual
Before using your SleepHalo™ we recommend reading this guide to prevent any
damage that could occur due to misuse.
We also recommend registering your product on our website to activate your
2-year warranty.
Visit: www.sleephalo.com/register
Compatibility for Wireless Charging
SleepHalo™ has been designed to be compatible with Qi-enabled phones. A list
can be found on our website.
If your phone is not wireless compatible it can still be used with your
existing wired charger by placing the plugged-in phone onto SleepHalo™. You
will then benefit from the radiation protection offered by SleepHalo™.
Connecting your SleepHalo™
Decide which side of the bed you wish to place your SleepHalo™, noting that the raised protection shield should be between you and the phone. On the underside of the product you can route the power cable in 2 directions. Choose which route is best, plug in the connector to the power port and clip the cable through the rebated area.
Connect SleepHalo™ USB connector into the power adapter.
Plug SleepHalo™ power adapter into a wall socket.
Using your SleepHalo™
To charge wirelessly, the phone must be placed onto SleepHalo™ with the screen
facing up. The indicator LED on the side will change from red to blue once the
hone is correctly placed. Place the phone in the center of SleepHalo™.
If the red LED flashes, this indicates the phone is not aligned correctly. Fully remove and then replace. Correct charging can also be confirmed by checking the the screen of your phone for the charge icon.
| LED Colour | SleepHalo™ Status |
|---|---|
| Red | Standby |
| Blue | Charging |
| Green | Fully Charged (dependent on phone) |
| Flashing | Phone not aligned correctly Or foreign object detected |
How to position SleepHalo™ on the bedside table
When positioning SleepHalo™, position it so that when you are laying down you cannot see the screen of your phone.
SleepHalo™ has rubber feet attached to the bottom to prevent it from slipping. If you have a phone with a magnetic back, then sticky feet can be purchased from our website to hold SleepHalo™ down.
For further set-up information and Troubleshooting please visit our support page at www.sleephalo.com or email us at support@angelelectronics.com
Safety Information
- Using a different power adapter other than the one supplied with SleepHalo™ is at your own risk.
- Do not disassemble SleepHalo™, it is a sealed device.
- Whilst the phone is charging do not cover.
- Do not place anything other than your phone onto SleepHalo™.
- Do not use outdoors or in damp conditions.
- Unplug if SleepHalo™ is not used for extended periods of time.
- If you can see damage to SleepHalo™ do not use it.
- To clean SleepHalo™ unplug and use a soft damp cloth.
- Depending on your phone, you might hear faint noises while your phone charges.
- Do not place anything between your phone and SleepHalo™. Remove anything (credit cards) that are stored in the back of your phone case.
Specification
Power Adapter
- AC Adapter : 100-240V, 50/60 Hz 0.3A
- Output : 5V 1A
SleepHalo™
- Input: 5V 1A
- Output: 5W
- Wireless Range : 5mm
Declaration of Conformity (FCC)
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SleepHalo™ is a trademark of Angel Electronics Ltd ©
Angel Electronics Silverstone Technology Park, Silverstone, NN12 8GX
info@angelelectronics.com
SleepHalo™ User Manual V1.1 E&OE
References
- SleepHalo The world’s first wireless phone charger with radiation protection
- Product Registration - SleepHalo
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>