Sage BJE530/SJE530 Cold Plus Nutri Juicer User Guide

BJE530/SJE530 Cold Plus Nutri Juicer

the Nutri Juicer‰ Cold Plus

BJE530/SJE530

QUICK GUIDE

Sage

SAGE® RECOMMENDS SAFETY FIRST

At Sage® we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.

IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE

• A downloadable version of this
document is also available at
sageappliances.com
• Before using the first time ensure
your electricity supply is the
same as shown on the label on
the underside of the appliance.
• Remove and safely discard
any packaging materials
before first use.
• To eliminate a choking hazard
for young children, safely
discard the protective cover
fitted to the power plug.
• This appliance is for
household use only. Do not
use the appliance for anything
other than its intended use.
Do not use in moving vehicles
or boats. Do not use outdoors.
Misuse may cause injury.
• Fully unwind the power cord
before operating.
• Position the appliance on a
stable, heat resistant, level,
dry surface away from the
edge and do not operate on
or near a heat source such as
a hot plate, oven or gas hob.
• Vibration during operation may
cause the appliance to move.
• Do not let the power cord
hang over the edge of a bench
or table, touch hot surfaces
or become knotted.
• Always ensure the appliance
is turned OFF, unplugged at
the power outlet and has been

allowed to cool before cleaning,
attempting to move or storing.
• Always turn the appliance to
the off position, switch off at
the power outlet and unplug
at the power outlet when the
appliance is not in use.
• Do not use the appliance
if the power cord, plug, or
appliance becomes damaged
in any way. If damaged or
maintenance other than
cleaning is required, please
contact Sage Customer Service
or go to sageappliances.com
• Any maintenance other
than cleaning should be
performed by an authorised
Sage® service centre.
• Children should not play
with the appliance.
• Cleaning of the appliance
should not be carried out
by children unless they are
8 years or older and supervised.
• The appliance and its cord should
be kept out of reach of children
aged 8 years and younger.
• The installation of a residual
current safety switch is
recommended to provide
additional safety when using
all electrical appliances. Safety
switches with a rated operating
current not more than 30mA
are recommended. Consult an
electrician for professional advice.

• Always ensure the appliance is
properly assembled before use.
The appliance will not operate
unless properly assembled.
• Do not use the appliance
on a sink drain board.
• Keep hands, fingers, hair,
clothing as well as spatulas and
other utensils away from moving
or rotating parts during operation.
• Do not use the appliance for
anything other than food and/or
beverage preparation.
• In order to avoid the possible
hazard of the appliance starting
by itself due to inadvertent
resetting of the overload
protection, do not attach an
external switching device (such as
a timer) or connect the appliance
to a circuit that can regularly
switch the appliance on and off.
• Carefully read all instructions
before operation and save for
future reference.
• The appliance can be used by
persons with reduced physical
or mental capabilities or a lack
of experience and knowledge,
only if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
• This appliance shall not be
used by children.
• Do not leave the appliance
unattended when in use.

• Do not push food into the feed
chute with your fingers or other
utensils. Always use the food
pusher provided. Do not place
hand or fingers into the food
chute when it is attached to
the appliance.
• Do not juice stone fruit unless
seeds and/or stones have
been removed.
• Do not operate the juice
extractor without the pulp
and juice container in place.
• Make sure the stainless steel
filter basket has stopped
rotating and the motor has
completely stopped before
releasing the safety locking arm
and/or attempting to move the
appliance, when the juicer is not
in use, and before disassembling,
cleaning and storing.
• Any significant spillage onto
the surface under or around the
appliance, or onto the appliance
itself, should be cleaned and
dried before continuing to use
the appliance.
• Be careful when handling the
stainless steel filter basket as
the small cutting blades at the
base of the filter basket are
very sharp. Mishandling may
cause injury.

• Remove rind from all citrus
fruit before juicing.
• Do not use the appliance if
the rotating sieve (filter basket)
or lid is damaged.
• Always make sure juicer cover
is clamped securely in place
before motor is turned on.
Do not unfasten interlock arm
while juicer is in operation.
The symbol shown
indicates that this appliance
should not be disposed of
in normal household waste.
It should be taken to a local
authority waste collection centre
designated for this purpose or to
a dealer providing this service.
For more information, please
contact your local council office.
To protect against electric
shock, do not immerse the
power plug, cord or appliance in
water or any liquid.

SAVE THESE INSTRUCTIONS

Components

A. Food pusher (not dishwasher safe)
B. Interlocking safety arm Stops juicer operating without cover locked into place.
C. Juicer cover (dishwasher safe)
D. Stainless steel filter basket (dishwasher safe)
E. Pulp container (dishwasher safe)
F. Filter bowl surround (dishwasher safe)
G. 2 Speed control and off dial
H. Overload protection indicator light
I. 2 litre juice jug and sealing lid with built in froth separator (dishwasher safe)
J. Juicing Nozzle Can be placed over spout to juice directly into a cup (dishwasher safe)

Rating Information
220–240V~ 50/60Hz 1200–1300W

Assembly

Before first use
Before using your juicer for the first time, remove
and safely discard any packaging materials and
promotional stickers and labels.
Ensure the power cord is unplugged.
Wash the filter bowl surround, filter basket, juicer
cover, food pusher, pulp container and juice jug
and lid in warm, soapy water with a soft cloth.
Rinse and dry thoroughly.

1. Place motor base on a flat, dry surface
such as a countertop. Ensure that the
juicer is switched to OFF at the dial,
and the power cord is unplugged.
2. Place filter bowl surround on top
of the motor base.

3. Align the arrows at the base of the
stainless steel filter basket with the arrows
on the motor drive coupling and push
down until it clicks into place to create
a secure fit with the motor base.

4. Place the juicer cover over the filter bowl
surround, positioning the lower part of
the feed chute over the stainless steel
filter basket.

5. Raise the safety locking arm up and locate
into the two grooves on either side of the
juicer cover.

6. The safety locking arm should now be
in a vertical position and locked into place
on top of the juicer cover.

7. Slide the food pusher down the food chute
by aligning the groove in the food pusher,
with the small protrusion on the inside of the
top of the feed tube.

8. Place the pulp container into position by
tilting and lifting the motor base slightly.
Insert the pulp container under the juicer
cover on the back ensuring it is supported by
the juicer cover and motor base.
9. Fit the lid to the juice jug and position jug
under juice spout.

Juice jug
Juice can be preserved in the juice jug for up to
3 days by following these steps.

1. Lift the lid off the jug and rotate 180°
2. Press down firmly to replace the lid
3. Store juice in the fridge

NOTE
Storage time depends on the ingredients being
juiced and the freshness of the fruit prior to juicing.
Juice must be stored in the refrigerator between
2°C to 4°C.

Functions

1. Wash your selection of fruit and vegetables
to be juiced. Most fruit and vegetables
such as apples, carrots and cucumbers
will not need to be cut or trimmed to
size as these will fit whole into the feed
chute. Ensure vegetables such as beets,
carrots etc. have all soil removed, are
washed well and trimmed of leaves
before using.
2. Plug the power cord into a 220V – 240V
power outlet.

IMPORTANT
Do not load Feed Chute with produce before
the Juicer has reached the selected speed.

3. Turning the Juicer On
Turn dial to desired speed setting. Turn
Dial to “Low” setting for soft fruits and
vegetables and to “High” setting for hard
fruits and vegetables. See Speed Selector
Guide table on the next page to match
speed and produce type for maximum yield.
“Low” range, while it may not maximise
yield of some produce, allows you to
extract juice at a significantly lower noise.
4. With the motor running, place food into
the feed chute and use the food pusher
to gently guide food down. To extract the
maximum amount of juice, always push
the food pusher down slowly.
5. Full Juice Jug
You can keep juicing until the Juice Jug
is filled to max. level.
6. Continuous Juicing
Having just filled and removed a Juice
Jug with fresh juice, you can place an
empty Juice Jug back onto the nozzle and
continue juicing without disassembly. When
the Pulp Container is near full with pulp, turn
the Dial to “Off”, remove the Pulp Container
only and empty contents. Replace the
empty Pulp Container and turn Dial to
desired speed selection to continue juicing.

SPEED SELECTOR GUIDE

FOOD TYPE SPEED
APPLES High
BABY SPINACH High
BEETS High
BELL PEPPER High
BLUEBERRIES High
BROCCOLI High
CABBAGE High
CARROT High
CELERY High
CITRUS FRUITS (peeled) Low
CUCUMBER High
GINGER High
GRAPES (seedless) Low
HONEYDEW MELON (peeled) High
KALE High
KIWI (peeled) Low
MANGO (peeled, pit removed) High
MINT High
PEACH (pit removed) High
PEARS High
PINEAPPLE (peeled) High
RHUBARB High
SQUASH High
STRAWBERRIES High
TOMATOES High
WATERMELON (peeled) Low
ZUCCHINI High

NOTE
• Do not allow the pulp container to overfill as
this may affect the operation of the appliance.
• The juicer is fitted with a safety device which
safeguards against overheating with excessive
loads. If overheating occurs, the juicer will
automatically activate the overload protection
device and the unit will switch itself off. When
the overload protection is activated, unplug the
juicer from the power outlet for 30 minutes to
allow the unit to cool. Then plug juicer into the
power outlet and use as normal.

WARNING
Never use fingers, hands or utensils to push food
down the feed chute or to clear the feed chute.
Always use the food pusher provided.

The stainless steel filter basket contains small
sharp blades to cut and process fruit and
vegetables. Avoid touching the blades when
handling the filter basket.

Care & Cleaning
Ensure the juicer is turned off by turning the
juicer dial to the OFF position. Then unplug
the power cord.

Cleaning
1. Remove Juice Jug.
2. Remove Pulp Container.
3. Disengage Locking Bar, pull up entire

Juice Collector Assembly and take to sink.
Rinse all parts after use (except the motor base)
under running water to clear away the majority of
juice and pulp. Wash in warm soapy water with a
soft cloth.

To avoid food drying on to the blades, mesh or
transparent parts, rinse and wash as soon as
possible after use.

Pulp container
To minimize cleaning, you can line the pulp container
with a biodegradable bag to collect the pulp.

Motor base
To clean the motor base, wipe with a soft, damp
cloth then dry thoroughly. Wipe any excess food
particles from the power cord.
Do not immerse the motor base in liquids.

Cleaning agents
Do not use abrasive scouring pads or cleaners
on either the motor base or the jug, as they may
scratch the surface. Use only warm soapy water
with a soft cloth.

Dishwasher
Wash all parts (except the motor base) in warm
soapy water with a soft cloth. All parts except for
the motor base and food pusher are dishwasher
safe. However washing parts on a regular base
in the dishwasher can shorten the life of them
due to prolonged exposure to harsh detergents,
hot water and pressure.

Cleaning the parts in the dishwasher also may
cause parts to deteriorate so inspect the parts
regularly and stop using the product if any signs
of damage is noticed.

Filter basket

To ensure consistent juicing results, always clean
the filter basket thoroughly immediately after use.
If pulp is left to dry, it may clog the fine pores of the
filter mesh, which can affect juicing performance.
The filter basket can be soaked in hot soapy water
for 10 minutes, if necessary.

Hold the filter basket under running water and use
brush (supplied with the juicer) in a circular motion
to clear away pulp from the inside of the basket,
including the blades. Turn over to brush away
pulp from the outside of the basket, and repeat
if necessary.

After cleaning, hold up towards a light source to
check that the fine mesh pores are not blocked.
If blocked, soak the filter basket in hot water with
10% lemon juice to loosen, and brush under
running water again.

Do not soak the filter basket in bleach, harsh
chemicals or abrasive cleansers.
Always treat the filter basket with care,
as it can be easily damaged. Do not use if there
is any damage or deformation to the filter mesh.
Filter basket can be washed in the dishwasher
(top shelf).

The center of the filter basket has an array of small,
sharp blades. Do not touch these blades when
handling the filter basket.

Stubborn food stains
Discoloration of the plastic may occur with strongly
colored fruit and vegetables. To help prevent this,
wash parts immediately after use.
If discoloration does occur, the plastic parts can be
soaked in water with 10% lemon juice or can be
cleaned with a non-abrasive cleaner.

Troubleshooting

Juicer will not work when switched ON
• The safety locking arm may not be correctly engaged in the vertical
operating position. Check the top cover is properly aligned and the locking
arm is located firmly into the two grooves on either side of the juicer cover.
• Motor overload protection may have operated (see below).

Overheating with excessive loads
• The juicer is equipped with an internal self-resetting overload to prevent the
motor from damage under heavy or continuous loads. If the motor suddenly
stops working, turn the dial to OFF, and unplug the unit from the power
outlet. Allow the juicer to cool for at least 30 minutes before operating again.
NOTE: The unit MUST be turned off in order for it to cool and be reset.
• Despite this overload protector, we suggest juicing in smaller batches,
without excessive pushing force, to avoid overheating and stalling and to
maintain the life of the motor.

Excess pulp building up in the stainless steel filter basket
• Stop juicing, disassemble to scoop excess pulp off the juicer cover.
Reassemble and continue juicing. Alternating soft and hard ingredients
may help avoid this.

Pulp too wet and reduced extracted juice
• The cleaner the filter, the better the juice yield, and dryer the pulp. Be sure
to thoroughly clean the juicer as soon as possible after each use. Remove
the stainless steel filter basket and thoroughly clean mesh walls with a
cleaning brush. Rinse the filter basket under hot water. If the fine mesh
holes are blocked, soak the basket in a solution of hot water with 10%
lemon juice to unblock the holes or wash in the dishwasher (top shelf).
This will remove excess fiber build up which could be inhibiting the flow.

Juice leaks between the rim of the juicer and the juicer cover
• Try a slower juicing speed (if possible) and push the food pusher down the
feed chute more slowly.

Juice sprays out from spout
• The juice is being extracted too High; try a slower juicing speed (if possible)
and push the food pusher down the feed chute more slowly.

Motor appears to stall when overload protection LED flashes
• Wet pulp can build up under the juicer cover and stall the juicer if the juicer
is used excessively without cleaning. If this occurs, disassemble and follow
the cleaning instructions to clean the filter bowl surround, the stainless
steel filter basket and the juicer cover. The juicer can also stall if excessive
force is used to push produce down the feed chute. If this occurs, ensure
that a more gentle pressure is used to push produce down the chute.
• The juicer will automatically stop operating if too much food is being
processed at one time. Try processing a smaller amount per batch. To
continue juicing, reset the juicer by turning the juicer OFF and back ON.
• Turn on the juicer before putting ingredients in the chute. Pressing
ingredients down before the juicer reaches full speed can cause the motor
to stall or overload. Use gentle to moderate pressure on the pusher. Lower
pressure produces a better juice yield.
• Hard fruit and vegetables will put excess strain onto the motor if a low
speed is selected. Refer to the juicing guide to determine the correct speed
for the fruit and vegetables selected for juicing.

Overload protection LED light flashing during the use
• This indicates the motor speed is slowed down to an inefficient level.
This may be caused by excessive pushing force on the pusher or too much
pulp building up on the lid or in pulp pin. Use moderate pushing force on
the food pusher and regularly clean the lid and pulp bin to ensure the juicer
is operating at optimal speed.

Overload Protection LED is on
• This indicates motor overload protection is activated. To reset the unit,
turn the dial to OFF, unplug the juicer and let the motor cool down for
25–30 minutes, then plug the juicer back in.

If any of the above issues persist, or if you have questions, stop use of the juicer and contact Sage® Customer Service.

Guarantee

2 YEAR LIMITED GUARANTEE
AND 5 YEAR LIMITED MOTOR
GUARANTEE
Sage Appliances guarantees this product for
domestic use in specified territories for 2 years for
all parts of the product and 5 years for the product’s
motor from the date of purchase against defects
caused by faulty workmanship and materials.
During this guarantee period Sage Appliances will
repair, replace, or refund any defective product (at
the sole discretion of Sage Appliances).
All legal warranty rights under applicable national
legislation will be respected and will not be
impaired by our guarantee. For full terms and
conditions on the guarantee, as well as instructions
on how to make a claim, please visit
www.sageappliances.com.

BRG Appliances Limited
Unit 3.2, Power Road Studios,
114 Power Road, London, W4 5PY
Freephone (UK Landline): 0808 178 1650
Mobile Calls (National Rate): 0333 0142 970

Sage

www.sageappliances.com
Registered in England & Wales No. 8223512
Registered in Germany No. HRB 81309 (AG Düsseldorf)
Registered in France No. 879 449 866 RCS

Due to continued product improvement, the products illustrated or photographed in this document may vary slightly from the actual product.

Copyright BRG Appliances 2021

References

• Sage Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>