Shenzhen Core Lmage XC005 Car Stereo System Instruction Manual

Core Lmage XC005 Car Stereo System
Instruction Manual

XC005 Car Stereo System

1. Turn off the car engine
2. Insert the MicroSD card into the recorder card slot
3. Fix the recorder on the front windshield with the double-sided tape provided by the machine
4. Plug the car charger into your car cigarette lighter
5. Connect the car’s USB port to the car charger with a charging extension cord
6. Adjust the lens position to make sure the lens is level with the ground
7. Start the engine and check that the machine is properly mounted (Pay attention to)When the machine is installed correctly, the machine starts to record, and the video  indicator light flashes, please pay attention to check whether the picture on the display screen is normal

Power Supply Connection Diagram

1. USB Power Port
2. Car Cigarette Lighter

Wiring and installation of the rear camera

• The installation method of the rear camera varies according to the installation position. Confirm the installation position and then select an appropriate installation method.
• After determining the installation position, clean the oil and dust on the surface of the installation position first. If the paste is not firm, the rear camera may fall off  during driving.
• Tear off the release paper of the double-sided adhesive tape on the camera bracket, stick it in the confirmed installation position, and press it firmly.
• Adjust the Angle of the rear camera while confirming the image on the LCD screen.
• It is suggested that the rear camera is better installed outside the car. This camera has waterproof function, don’t worry about it.
• For the sake of safe driving, please arrange the wires properly and do not interfere with driving.
• Please do not cut the rear extension cable for lengthening or refit, which may damage the machine or vehicle, and the rear camera will not work stably.

Introduction to the function of the dashcam

1. Power interface (type-c)
   Connect to DC 5V power supply to power the driving recorder. When the car turns off, it will automatically stop recording and save the recorded video file.

2. AV pull back camera interface
   Connects to the standard rear camera AV-in port.

3. the OK key
   Function A: Video recording function
   On the recording screen, press the [OK] key to start recording, and press the [OK] key again to stop recording. Function B: Confirm function.
   On the menu page or playback preview page, press the OK key to confirm the selection function.

4. [M] key (Menu key/Mode key/lock key)
   Function A: Menu key function
   Press the [M] key in the video interface to enter the recording image menu interface. Press the [V] down key again to enter the video interface.
   On the recording screen, press [M] twice to enter the system menu screen. Press [M] again to return to the recording screen. Function B: Mode key.
   Long press [M] on the video screen to switch between the video recording screen and playback screen
   Function C: Lock key.
   Press the [M] key to lock the current video file while recording.

5. [A] Up key/Video recording key /wifi switch Function A: up button selection function On the menu page/video playback preview page, press [A] to select the function.
   Function B: Enables the recording shortcut switch
   In the video screen, press the up key [A] to open the video recording. At the same time, the screen will display the video recording open mark 0. Press [A] again.
   The up button disables recording and the on-screen recording will change to
   Function C: wifiK switch function
   In the video interface, long press [A] up button to open wifi. The wifi connection interface is displayed, and the
   wifi name and password are displayed. Long press [A] up button again to close wifi and return to the video interface.

6. [V] down button/camera preview switch button
   Function A: Scroll down button selection function
   Press [V] Down on the menu page/video playback preview page to select the function.
   Function B: Switch function
   Short press [A] up button in the video interface of insertion and pullback to switch the front and back video images. There are four modes: front camera preview, front +  rear small window camera picture preview, front + rear left and right split screen preview, and rear camera picture preview.

7. [Power] key
   In THE SHUTDOWN state, press [POWER] button to TURN on the power of the machine, and the machine will start to work automatically. In the boot state, long  press the [power] button for 3 seconds, the machine will automatically save the video file and user Settings and shut down.

8. MicroSD card slot
   Insert the MicroSD card, and the video file will be stored in the MicroSD card. Memory card usage: Please determine the insertion direction of the MicroSD card. If the  insertion direction is incorrect, the unit and the MicroSD card may be damaged. Please use the high-speed MicroSD card that conforms to the SDHC specifications.  Support for 8 ~ 128 G.

9. [RESET] RESET key
   In the case that the machine is dead and cannot be started normally, click the button in the reset hole with a small needle and restart the machine after reset.

The main interface

Power on automatically start recording and display the camera preview interface

Video playback
To enter the video playback preview screen, hold down the M key in the video stop state.

Press the up and down keys to select a video file to play, and press the OK key to play the current video file.
Video File Identifier
2022031509332_0000003F F Indicates the front camera video file.
2022031509332_0000003R R indicates the rear camera video file
In short video playback screen press the M key can be set into the playback interface, short press the button to delete or protect file operations, delete option is to delete the  current file and delete all two options, can only delete the cycle of ordinary video files, lock emergency files need to select the unlock current protection optionsor unlock all  files to delete the lock file short press the M key to return To the main interface of video file, long press M key in the main interface of video playback to return to the main interface of recording.

Setting up

In the video stop state, press M key to enter the video setting screen video

1. Resolution; The Settings can be switched between 2K P30, 1080P P30, and default 2K P30.

2. Loop recording: Set the segment duration of loop recording :1 minute, 2 minutes and 5 minutes.
   The default duration is 1 minute.

3. WDR:WDR technology restores dark and bright details to make shooting clearer. On or Off, on by default.

4. Gravity sensing: According to the gravity sensing sensitivity, low, medium, high and three modes can be set.
   Different sensitivities correspond to the corresponding file locking sensitivity. This machine has built-in collision sensor (G-sensor). In case of serious vehicle collision,  the recorder will lock the current image data at the time of the accident, and the locked image will be saved as a special file, which will not be cyclically overwritten.

5. Audio recording: Turn on or off audio recording when recording, and turn on by default.

6. Date label: on or off, on by default.

7. Preview mode: before recording, after recording, before large after small and before small after four modes.
   This mode is the preview screen displayed on the boot screen.

8. Encoding: Video recording encoding mode has two ways: H264 and H265.

After turning on WiFi, long press the up button again to turn off WiFi.

1. WiFi: Turn on or off WiFi. Long press the upper button in the video preview screen to quickly turn on WiFi.

2. Date & time: press the OK key to set the date and time. In order to effectively record the date and time of collecting evidence of driving safety accidents.
   Please set the correct time before using the machine.

3. Volume: On or off, on by default.

4. Language setting: Click the language setting function to switch the language.

5. Frequency of light source: 50HZ and 60HZ can be selected by clicking on it. The default is 50HZ.

6. Screen saver backlight: The screen backlight can be set to turn off the countdown time, including off,
   1 minute, 3 minutes, 5 minutes, and off. If it is steady on, the screen backlight is turned off by default.

7. GPS watermarking: You can set the position, longitude, latitude, and time date of the video file to display the watermarking, and the default display is enabled.

8. Time zone setting: The user can select the time according to the local time. After GPS positioning, the time, date and time will be automatically updated to the local time.

9. Formatting: You can format the TF card and back up important data regularly. Formatting the microSD card will delete all unrecoverable files in the microSD card.  Please format the microSD card regularly. If used for a long time, the recorder will stop recording due to the insufficient capacity of locked files. It is recommended to  format once every 1-2 weeks.

10. Default Settings: Click Restore factory Settings. The system will prompt you whether to restore factory Settings.

11. Version: Click to view the relevant information of the system version number. The QR code below is the installation and download link of the mobile APP (LuckyCam).

Download APP on mobile phone

1. Enter the Settings in the machine, find the version number and click to view the APP download two-dimensional code, and scan the two-dimensional code for  installation and download or scan the following two-dimensional code directly for installation and download.
   http://a.app.qq.com/o/simple.jsp?pkgname=com.ntk.LuckyCam&fromcase=40003

2. Before connecting to WiFi, users need to turn on the WiFi function of the host and click on the homepage Turn on the WiFi function and will appear WiFi Name WiFi  password (default 12345678, the user can change the password after connecting the mobile APP), the host cannot operate after the WiFi is turned on, and the host can  only be operated after the WiFi is turned off.

3. After downloading the APP, open the WIFI function of the mobile phone, connect the hotspot name displayed on the machine, enter password 12345678, wait for the  successful connection between the mobile phone and the machine, open the mobile APP[LuckyCam], click the camera position below, the mobile APP will automatically  connect to the machine, and then the mobile phone will display the preview picture of the camera on the machine. The machine will turn off any  operations and only show a preview of the camera.

Matters needing attention

Disclaimer
The traffic recorder is a recording device for the image and sound of a vehicle during its journey. It is only used as an auxiliary reference in case of an accident.
Special note: The machine must be in normal working state to record video files.
However, the image will be damaged or lost in the following circumstances;

1. If the MicroSD card is removed during recording, the last video file may be damaged or lost.
2. If the video is powered off illegally, the last video file may be damaged or lost.
3. Video files are damaged or lost due to a destructive collision during recording.
4. The memory card is loose due to a large collision during the recording process, which will damage the video file or cause the loss of the video file.
5. Don’t squeeze the dashcam at will.
6. If the tachograph is abnormal, press the reset button, and the tachograph will power off and restart under the MicroSD card slot in the body.
   [Attention] When the machine is installed correctly, the machine starts to record, and the video indicator light flashes. Please pay attention to check whether the screen  is normal, if the screen is inverted, please timely contact us.
   [Attention] Please format the MicroSD card in the machine menu for the first time.

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this  device must accept any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not  installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and  on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>