REAL-EL STAB SLIM-300 Automatic Voltage Regulator User Manual

REAL-EL STAB SLIM-300 Automatic Voltage Regulator User Manual

1. BUYER RECOMMENDATIONS

• Unpack the device Make sure there are no accessories left in the box. Check up the device for damage; if the product was damaged during transportation, address the firm, which carried out the delivery; if the product functions incorrectly, address the dealer at once.

• Check up the package contents and availability of the warranty Make sure the warranty card
  has a shop stamp, a legible signature or the seller’s stamp and purchase date, and the goods number corresponds to that in the warranty card. Remember: in case of warranty card loss or discrepancy of numbers you forfeit the right for warranty repairs.

• Do not switch on the device immediately after you bring it into a room from environment with negative temperature! After unpacking, the device should be kept in conditions of room temperature for at least 4 hours.

• Before installing and using the device, read this Manual carefully and keep it for future

2.APPLICATION

Automatic voltage regulator (AVR) is designed for providing various equipment with high-quality stable electric power supply in conditions of significant and continuous deviations of mains voltage and protecting consumer devices against overload, influence of high frequency and impulse interferences.

3. SAFETY PRECAUTIONS

Before using this device, please read the safety rules carefully:
ϜIt is strongly forbidden to open the cover of the device, there is high voltage inside. If some problems occur, please read the operation manual carefully and address an authorized service
center. For the list of authorized service centers please go to www.real- el.com.
ϜDo not let liquid get inside the device, it can cause short circuit or electric shock.
ϜIn case there are signs of improper operation of the device (sparkling, unusual smells, etc.), unplug the device from the mains immediately and address your nearest authorized service center.
ϜIt is forbidden to connect the automatic voltage regulator to devices with power consumption higher than its maximum output power. It can cause breakdown of the device.
ϜThis device is not intended for use by persons (including children) with reduced physical, mental capabilities, lack of experience or knowledge; use of the device by such persons is permitted only under the condition of supervision or instructions for the use of household appliances by persons responsible for their safety.
Ϝ Children should be supervised by authorized personnel to exclude their playing with the appliance.
ϜDo not use the appliance with a damaged power cord or plug, or after handling liquids, falling or any other damage. To avoid electric shock, do not attempt to disassemble or repair the appliance yourself. If necessary, contact a specialized service center.

It is strongly forbidden to operate the device in the following conditions:

• LQGXVW\HQYLURQPHQWRUHQYLURQPHQWFRQWDLQLQJKLJKO\LQԜDPPDEOHJDV
• at temperature higher than 40 °C or lower than 0 °C;
• at humidity level higher than 90 %;
• in direct sunlight or next to heating elements;
• in vibration areas;
•  outdoors.

Ϝ,QFDVHRIԛUHXVHRQO\SRZGHUԛUHH[WLQJXLVKHUDVZDWHUFDQFDXVHHOHFWULFVKRFN
ϜThe automatic voltage regulator should be installed in proximity to power supply, then it will be easier to unplug the device if necessary.

Caution! There is high voltage inside on the insulation elements which can result in electric shock.

4. PACKAGE CONTENTS

ϜAutomatic voltage regulator – 1 pc
Ϝ Operation Manual – 1 pc
Ϝ Warranty card – 1 pc

Features

ϜHigh precision of output voltage
ϜCPU control
ϜProtection against high or low output voltage
ϜWall mount Slim design metal case
ϜWide range of input voltages 150-270 V
ϜDigital displays of input/output voltage
ϜToroidal transformer with built-in restorable thermal protection
ϜOptional 6s or 180s Switch On Delay time

Operation Manual

5. DESCRIPTION

• Digital display of the output voltage level

• L » – low voltage protection;

• H » – high voltage protection;

• C » – transformer temperature protection

• POWER : LED (green) lights up when there is a input voltage $ Digital display of the input voltage level

• DELAY : LED (yellow) EOLQNVDWZRUNLQJRԚGHOD\
  & PROTECTION: LED (red) lights up in case of accident (high/ low voltage protection operation, transformer thermal overload)

•  Wall mounting holes

• ( Output socket (the STAB SLIM-2000 has 2 output sockets) Delay selection button (180 or 6 s): while pressing the delay time will be 180 s, when not pressed – 6 seconds

• RESET/OFF: power switch with built-in fuse + Built-in power cord
  

6. MOUNTING

PSRUWDQW %HIRUH PRXQWLQW WKH UHJXODWRU PDNH VXUH WKDW DOO Н[LQJ elements durable fastened to the wall!
ϜFor securely wall mounting it is necessary to determine the type of wall material (wood, brick, concrete, drywall, and etc.) for corresponding fastener selection.
ϜMounting stabilizer location should be close to the wall outlet, considering the stabilizer power cord length.
ϜNext, make a mounting fasteners (not included) to the wall, considering the wall mounting holes location ‘ on the stabilizer rear panel (see Fig. 2).
Ϝ7KHQKDQJWKHVWDELOL]HURQԛ[LQJHOHPHQWV

Automatic Voltage Regulator

7. INSTALLATION

Attention! Before connecting the regulator, make sure that all consumer devices connected to it are off.
ϜBefore installing the AVR, please make sure that total power of all voltage consumers is lower than AVR power. Taking into account the starting load and power factor of voltage consumers, it is necessary to apply power margin factor of 1.2–1.5; for such equipment as air conditioners, fridges and other electric motors it should be 1.5–2.
Attention! When choosing an AVR, it is necessary to know that reduction of input voltage
LQFUHDVHVYDOXHRILQSXWFXUUHQWZKLFKPHDQVWKDWPD[LPXPSRZHURI$95LVUHGXFHGWRR
Such dependence is shown in the graph below:

Note. Adhere strictly to such dependence. If the condition stated above is not adhered to, warranty servicing becomes void!
ϜPlug the stabilizer power cord + in the wall outlet.
ϜTurn on stabilizer with switch * (RESET position).
ϜIf the AVR operates properly, green LED # illuminates, and yellow LED % will blink. At the same time the digital indicator ” will show the input voltage. The total delay makes 6 or 180 s depending on the “DELAY” button “RESET/ OFF” ) position. After the delay time yellow LED %WXUQVRԚDQG digital indicator $ will show the output voltage of the regulator. And only after that you can turn on the connected devices, consumers.
ϜWhen the mains voltage exceeds the allowable rate (lower threshold is 150 V, upper threshold is
270 V) the red LED & illuminates, the AVR disconnects the load automatically.
Attention! It is recommended to switch off the AVR and every connected consumer device when the power supply is dropped.

8. PAUSE FUNCTION

ϜThe Pause mode feature is designed to protect equipment in case of frequent drops of the mains supply. This is particularly important for consumer appliances with electric motors or compressors.
After power supply has been recovered, the AVR switches on within 6 or 180 seconds, depending on the ” DELAY ” button ” RESET/ OFF ” position.

9. PROTECTION FUNCTION AGAINST HIGH AND LOW INPUT VOLTAGE, OVERLOAD AND

OVERHEAT
ϜThe stabilizer is equipped with an circuit overvoltage and undervoltage protection. In the case of PDLQVYROWDJHGHYLDWLRQRYHU9RUEHORZ9LW WXUQVRԚ WKHORDGDXWRPDWLFDOO\$W WKHVDPH time red LED & illuminates. When the input voltage range returning to 150-270 V the stabilizer automatically resumes operation.
ϜIn case of overload or short-circuit AVR power switch will triggered. After elimination overload cause or short circuits, press AVR power switch (RESET position), and stabilizer will resume operation.

10. TROUBLESHOOTING

2.      There is no voltage in the power supply network.

3.      The fuse has activated. 4.The load connected is too powerful.

| 1.    Press the switch once again.

2.    Make sure that power supply is available.

3.    Disconnect the AVR from the power supply and reset the circuit breaker

4.    Disconnect some load.

The AVR is turned on, but there is no output voltage.| The AVR is out of order.| If the problem is not eliminated, please address an authorized service center.
The AVR often produces clicking sounds.| Input voltage is very unstable.| It is normal. The AVR regulates output voltage.
The AVR has disconnected the load. Active red indicator.| Input voltage is beyond possible regulation range of 150 – 270 V.| When input voltage is normalized, the AVR tuns on automatically.

If none of the above methods can solve the problem, please seek professional advice at your
nearest service center. Never attempt to repair the product by yourself.

11. SPECIFICATIONS

V/50 Hz
Output voltage| ~230 ± 8 % V/50 Hz| ~230 ± 8 % V/50 Hz| ~230 ± 8 % V/50 Hz| ~230 ± 8 % V/50 Hz
Switching time| y 10 ms| y 10 ms| y 10 ms| y 10 ms
Short circuit protection| available| available| available| available
Environment temperature| 0 – 40 °C| 0 – 40 °C| 0 – 40 °C| 0 – 40 °C
Humidity| up to 90 %| up to 90 %| up to 90 %| up to 90 %
Dimensions| 330 × 160 × 60 mm| 330 × 160 × 60 mm| 330 × 160 × 60 mm| 370 × 200 × 60 mm
Weight| 2.2 kg| 2.6 kg| 3.2 kg| 5 kg

Notes:

• Technical specifications given in this table are supplemental information and cannot give occasion to
• Technical specifications and package contents are subject to change without notice due to the improvement of

TM REAL-EL production

.

Models: STAB SLIM-300, STAB SLIM-500, STAB SLIM-1000, STAB SLIM-2000
Manufacturer: ENEL GROUP OU, Katusepapi tn 6, Lasnamäe linnaosa, Tallinn,
Harju maakond, 11412, Estonia. Made in China.
® Registered Trademark of ENEL GROUP OU. Estonia.

Read More About This Manual & Download PDF:

References

• REAL-EL

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>