ever SOLO High Resolution DAC and Headphone Amplifier Instruction Manual

June 3, 2024
ever SOLO

ever SOLO High Resolution DAC and Headphone Amplifier

Introduction

Thank you for choosing Eversole DAC-Z6.
DAC-Z6 is a compact and exquisite fully-balanced DAC and headphone amplifier. The decoding solution is XMOS 316 and dual ES9068 DAC chips, which support up to DSD512, PCM 768Khz@32Bit, and MQA decoding. Good decoding quality is guaranteed due to the low noise and distortion for D/A conversion.
Two independent channels correspond to two ES9068 DAC chips respectively for D/A conversion, so that channel interference are effectively avoided. High- precision resistors and fully balanced circuits are designed for lossless amplification for XLR, RCA, and headphone output. Channel separation, dynamic range, and sound integrity are greatly improved.
Multiple inputs on DAC-Z6 are available for hi-res digital audio decoding. USB DAC input can be connected to a computer and streamer; Type-C is to connect mobile devices like mobile phones or tablets; Optical and Coaxial are to connect streamers and CD players. DAC-Z6 can also connect mobile devices by Bluetooth, just like a Bluetooth decoder, it is BT5.0 and supports APTX HD, LDAC, etc.
The professional headphone driving circuit in DAC-Z6 supports good indicators and strong drive. As a high-performance headphone amplifier, high and low gain modes are optional, and headphones between 16-300 ohm impedance can be easily driven.
Eversole DAC-Z8 is the perfect partner for high-fidelity audio equipment or high-end headphones. The exceptional preamp performance, good sound quality, and strong headphone driving force will bring you with authentic HiFi music experience.
Please read this manual before using the device so that you could use it correctly.

Specification

Chassis Aviation aluminum alloy
Display Screen 3-inch TFT Screen
DAC ES 9068AS*2
Audio Processor XMAS XU316
OPA Chip RT6563D*5
Power Low noise switching power supply, AC 110-240V 50/60Hz

Bluetooth Audio
Input| Qualcomm QCC5125 Bluetooth module, BT5.0
Support SBC/AAC/aptX/aptX LL/aptX HD/LDAC Bluetooth protocol
USB-B DAC Input| Compatible with Windows (7, 10), Mac, Android, and IOS
Up to stereo DSD512, PCM 768KHz 32Bit, and MQA
USB-C DAC In| Compatible with Windows (7, 10), Mac, Android, and IOS
Up to stereo DSD512, PCM 768KHz 32Bit, MQA
Optical Audio Input| Up to stereo PCM 192KHz 32Bit, DSD64 Dop, and MQA
Coaxial Audio Input| Up to stereo PCM 192KHz 32Bit, DSD64 Dop, and MQA
analog audio
Output| Preamp output: XLR (balanced), RCA;
Headphone amp output: 6.35mm single-ended
USB Port| USB2.01 (only for firmware upgrade)
Control Methods| Remote control, mobile APP control, and knob control
Recommended
Headphone
Impedance| 16-3000 (low gain mode:16-320/high gain mode: 32-3000)
Rated Power| 9W
Dimensions| 270mm(W)
187mm(D) SOmm(H)
Packing List| Remote control
1, power tableful, USB cable1, product manual1
Analog Audio| XLR Audio Output
---|---
Output level(Vrms): 4.1Vrms@OdBFS
THD+N@A-wt: 0.000062%@1kHz (-124c113@lkHz)
THD+N@No-wt: 0.000069%@1kHz (-123dB@lkHz)
Noise@No-wt: <1.2uVrms
SNR @No-wt: 133dB@lkHz
Frequency response: 20Hz-20kHz(±0.1dB)
Crosstalk: -130dB@lkHz
DNR @No-wt: 133dB@lkHz
RCA Audio Output
Output level (Vrms): 2.3Vrms@OdBFS
THD+N@A-wt: 0.000086%@1kHz(-121dB@lkHz)
THD+)@No-wt: 0.000097%@1kHz(-120d13@lkHz)
Noise @No-wt: <1.5uVrms
SNR @No-wt: 126dB@lkHz
Frequency response: 20Hz-20kHz(±0.1dB)
Crosstalk: -123dB@lkHz
DNR@No-wt: 126dB@lkHz
Headphone
Low gain mode
Output level(Vrms): 1.2Vrms@OdBFS
Maximum undistorted power: 45 mW@32()
THD+N@A-wt: 0.00015%@1kHz(-116dB@lkHz)
THD+N@No-wt: 0.00018%@1kHz(-115dB®lkHz)
Noise @No-wt: <2uVrms
SNR@No-wt: 124dB@lkHz
Frequency response: 20Hz-20kHz(±0.1dB)
DNR @No-wt: 119dB@lkHz
High gain mode
Output level(Vrms): 2.3Vrms@OdBFS
Maximum undistorted power: 17.6 mW@3000
THD+N@A-wt: 0.00016%@1kHz(-116c1B@lkHz)

Hardware Introduction

Front panel

ever-SOLO-High-Resolution-DAC-and-Headphone-Amplifier-
\(1\)

Control knob
Volume adjustment:
The knob can control the volume when the device is in playback status. Rotate clockwise to increase volume while counterclockwise to decrease volume.
*Volume can be adjusted with step 0.5dB-3dB in the DAC setting.
Setting menu:
Short pressing the knob will access the setting menu. Rotate left/right to navigate the menu upward/downward. Short press the knob again to confirm or access the sub-menu.
Audio source selection:
Long press the knob to select the audio source, and rotate left/right to choose left/right audio source channels.

Rear panel

ever-SOLO-High-Resolution-DAC-and-Headphone-Amplifier-
\(2\)

Output

  1. Headphone output Connect a headphone with a 6.35mm single-ended jack to a DAC-Z6 headphone jack. Note: Select the suitable gain mode in DAC setting to adapt to headphones with different sensitivities and impedances. Headphone input has a higher priority than XLR/RCA, when it is in the mode of headphone output, the signal output of XLR/RCA will be disconnected.

  2. RCA output Connect DAC-Z6 RCA output to a power amplifier or active speaker RCA input by an RCA audio cable.

  3. XLR balanced output Connect DAC-Z6 XLR output to power amplifier or active speaker XLR input by XLR audio cable.
    ever-SOLO-High-Resolution-DAC-and-Headphone-Amplifier-
\(3\)In order to reduce the possible signal interference of the RCA and XLR simultaneous output, XLR and RCA can be output separately by setting in the menu. Higher audio indicators and better sound quality can be obtained through separate output.
    Input

  4. Optical/Coaxial input
    Connect this device with S/PDIF devices like a media players and the CD players by an Optical/Coaxial audio cable.
    Please set the signal source to Optical/Coaxial.

  5. USB DAC Input
    Connect the computer to the USB DAC input of this device by USB-A to USB-B cable. The computer is the digital audio source, this device is used as a computer sound card to decode audio signals.
    Please select the signal source to “USB DAC IN”.

Notes:

Please refer to the File Download part below to download Windows driver.
EVERSOLE DAC-Z6 is working as the audio output device when connecting with the computer, the settings are as follows.
Windows: Download and install the driver on the computer, find “Control Panel>Hardware and Sound >Sound >Playback”, then select “EVERSOLE USB AUDIO”.
Mac:  No driver is needed to be installed, find “System Preferences

Sound>Output”, then select “EVERSOLE USB AUDIO”.

Remot controlever-SOLO-High-Resolution-DAC-and-Headphone-Amplifier-
\(4\)

Basic Setting

  1. Long press then rotate the knob or press ” ” key on remote control to switch input source.

  2. Settings
    Short press the knob or press “  ” key on remote control.

  3. Output port Enter the setting menu > Output port > XLR output/ RCA output/ XLR and RCA output.

  4. Headset gain Enter the setting menu > DAC > Headset gain, select high gain or low gain.

  5. Votome control steps
    Enter the setting menu > DAC > Volume control steps, adjust the suitable volume step. “Power-on volume” is to select the volume when powering on, customize the volume or keep the last volume.

  6. Filter
    Enter the setting menu > DAC > Filter, adjust DAC filtering characteristics for DSD or PCM to output different sound styles.

ES9068AS DAC (PCM) CHARACTERSTICS

FILTER| IMPULSE RESPONSE| CHARACTERISTIC| Distance| Edge
---|---|---|---|---
Fast Roll-Off,
Linear Phase
Filter| | Low order reverb,
natural| Far| Neutral
Slow Roll-
Off, Minimum
Phase Filte| | Intermediate reverb,
warm| Middle| Neutral
Hybrid, Fast
Roll-Off,
Minimum
Phase Filter| | High order reverb,
mellow| Close| Sharp
7. language
Enter the setting menu > General > Language, select language for menu and user interface.

  1. VU meter
    Enter the setting menu > General > VU meter, select VU meter mode in for the playback interface according to your preferences.

  2. Energy Saver
    Enter into Menu —>”General”—>”Energy Saver” to adjust the Screen Brightness, Standby and Screen Off Settings.
    Screen Brightness:  Adjust the brightness levels according to your preference.
    Standby: Select the time interval that you want the device to standby when no playback.
    The screen display will be turn off and DAC circuit will be cut off. The device will go back to work status when system detects the input of audio source or when we switch  audio source manually and press POWER key.
    Screen Off: Select the time interval to automatically turn off the screen when no operation is performed on the device. The screen will light up again once operating.

  3. Knob
    Enter the setting menu > General > Knob, set up the brightness level of the ambient light and customize function for short pressing the knob(system menu or input source selection).

  4. Disable Remote
    This function is for the situation when 2 or more EVERSOLO DACs in the same environment, so that DACs will not be controlled at the same time. Enter into Menu —> “General > ” — >”Other” —>”Disable Remote: Disable/Enable”
    Note:  If the device cannot be controlled by remote, please check whether remote is disabled.

  5. Firmware upgrade
    Download the firmware package on EVER SOLO official website to a U disk, connect the U disk to DAC-Z6 USB A port. Access system menu> About> Upgrade to upgrade firmware, wait for the device to restart automatically after upgrading the firmware successfully.
    Note:  Don’t unplug the U disk or power the device off during the firmware upgrade period.

MQA (Master Quality Authenticated)

The DAC – Z6 includes MQA technology, which enables you to play back MQA audio files and streams, delivering the sound of the original master recording. The DAC – Z6  LED glows green or blue to indicate that the unit is decoding and playing an MQA stream or file, and denotes provenance to ensure that the sound is identical to that of the  source material. It glows blue to indicate it is playing an MQA Studio file, which has either been approved in the studio by the artist/producer or has been verified by the  copyright owner. ever-SOLO-
High-Resolution-DAC-and-Headphone-Amplifier- \(19\)

MQA (Master Quality Authenticated)
MQA is an award-winning British technology that delivers the sound of the original master recording. The master MQA file is fully authenticated and is small enough to stream  or download.
DAC-Z6 adopts MQA technology to receive and decode MQA audio and provide master-level sound.
Visit mqa.co.uk for more information.
MQA and the Sound Wave Device are registered trade marks of MQA Limited © 2016

File Download

Download firmware, USB driver and controller app on the DOWNLOADS page of official website: www.eversolo.com 
Or scan the QR codes below to download.
When downloading the driver, please unzip the package, double click .exe file and complete the installation via the instruction.

Driver/App download

https://www.eversolo.com/Support/release_apk.html

Special note:
EVERSOLO will upgrade firmware from time to time in order to improve user experience, so that this manual might differ with the situation of real product. The functions or  parameters of this device are subject to adjustment without prior notice.
For more information, please visit our official website: www.eversolo.com
Safety Warning

  1. No water splashing or dripping, don’t put objects with liquids like vases on the device.
  2. The socket should be put aside the device for easy operation and no occlusions.
  3. It is a Class | device,there must be grounding measures inside the box when using.

Safe using below 2000m altitude.

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device  must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the  user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution:  Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals