GOBOS 041901 Moving Head Boreal 450 Zoom Instruction Manual
- June 3, 2024
- GOBOS
Table of Contents
GOBOS 041901 Moving Head Boreal 450 Zoom
Unpacking
Thank you for purchasing the fixture. Every unit has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit have arrived intact. In the case, the damage has been found or parts are missing, please contact the manufacturer or your dealer for further instructions. Do not return this unit to your dealer without first contacting them.
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING THE FIXTURE. SAVE IT FOR FUTURE REFERENCE.
Warning!
To prevent or reduce the risk of electrical shock or fire, do not expose this
unit to rain or moisture.
PLEASE consider that damages caused by manual modifications to the device are not subject to warranty.
Caution!
There are no user-serviceable parts inside this unit. Do not attempt any
repairs yourself; doing so will void your manufactures warranty. In the
unlikely event your unit may require service please contact the manufacturer
or your dealer.
PLEASE recycle the shipping carton whenever possible.
General Instructions:
To optimize the performance of this product, please read these operating
instructions carefully to familiarize you with the basic operations of this
unit. These instructions contain important safety information regarding the
use and maintenance of this unit.
Features
- Multi Colors
- Color Strobe
- Electronic Dimming 0 100%
- DMX 512 protocol
- Master/Slave synchronization
- LCD operation menu with function buttons
- Daisy Chain Units Together in DMX Mode
Safety Precautions
- To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture
- Do not spill water or other liquids into or onto your unit.
- Be sure that the local power outlet match of the required voltage for your unit.
- Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
- Disconnect from the main power before making any type of connection.
- Do not remove the cover under any conditions. There are no user-serviceable parts inside.
- Never operate this unit when its cover is removed.
- Never plug this unit into a dimmer pack
- Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
- Do not attempt to operate this unit, if it becomes damaged.
- This unit is intended for indoor use only; use of this product outdoors voids all warranties.
- During long periods of nonuse, disconnect the unit’s main power.
- Always mount this unit in a safe and stable matter.
- Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
- Cleaning The fixture should be cleaned only as recommended by the manufacturer. See Cleaning” for details.
- Heat The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
- The fixture should be serviced by qualified service personnel when:
- The power supply cord or the plug has been damaged.
- Objects have fallen, or liquid has been spilled into the appliance.
- The appliance has been exposed to rain or water.
- The appliance does not appear to operate normally or exhibit a marked change in performance.
Technical Specifications
Electrical
- Power supply :……………….…electronic auto-ranging
- Input voltage range :……………supply 90-250V, 50/60Hz
- Fuse :…………………………… 5 A@230V
- Power consumption :……………450W@230V, power factor=0.98
Optic
- Light source: TW (RGBW 15W) LED X30PCS
- LED life expectancy: 60,000 hours
- Dimmer: Smooth dimmer from 0-100% RGBW color mixing + CTC 8°-60°linear zoom
Motorized
- Pan/Tilt
- Pan movement range: 450°
- Tilt movement range: 300°
- 16-bit movement resolution
- Automatic Pan/Tilt position correction
- Pan movement 0°-450°at max…….Speed: 2.2 sec.
- Tilt movement 0°-300°at max…….. Speed: 1.2 sec.
- LCD operation
- Built-in demo sequences
- Silent fans cooling
- Strong three-phase motors
- Stand-alone operation
- Supported protocols: DMX512
- 2 DMX modes (13, 16 control channels)
Connection
- DMX data in/out: Locking 3-pin and 5-pin XLR
- AC power input: 1.5m power cord with plug
Rigging
- Mounting points: 2 pairs of 1/4-turn locks
- Mounting horizontally or vertically via 2 Omega brackets
Temperatures
- Maximum ambient temperature: 45℃
- Maximum housing temperature: 75℃
Minimum distances
- Min. distance from flammable surfaces: 3.0m
- Min. distance to lighted object: 2.0m
- Total heat dissipation: 1350 BTU/h (calculated)
- Pack size: 520(L) x 390(W) x 460(H) mm
- Weight (net): 13kg
- Warranty: 1 Year
Set-Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for the fixture, The model is Auto power supply, It is workable in 90-250V/50~60Hz. Please make sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture.
Connection to the mains
For protection from electric shock, the fixture must be earthed! Install a
suitable plug on the power cord, note that the cores in the power cord are
colored according to the following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualified electrician.
| Core (EU) | Core (US) | Connection | Plug Terminal Marking |
|---|
Brown Light blue
Yellow/Green
| Black White Green| Live Neutral Earth| L N
DMX512 connection
The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input
and output. The sockets are wired in parallel. Only use a shielded twisted-
pair cable designed for RS-485 and 3-pin or 5-pin XLR plugs and connectors in
order to connect the controller with the fixture or one fixture with another.
DMX-output
XLR mounting sockets (rear view):
DMX-input
XLR mounting plugs (rear view):
DMX Linking:
To ensure proper DMX data transmission, when using several DMX fixtures try to
use the shortest cable path possible. The order in which fixtures are
connected in a DMX line does not influence the DMX addressing. For example; a
fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at
the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
Building a serial DMX chain:
Connect the DMX output of the first fixture in the DMX chain with the DMX
input of the next fixture. Always connect one output with the input of the
next fixture until all fixtures are connected.
Caution:
At the last fixture, the DMX cable has to be terminated with a terminator.
Solder a 120Ω resistor between Signal (－) and Signal (＋) into a 3-pin XLR plug
and plug it in the DMX output of the last fixture.
Operating Modes: You can use the fixture in 4 ways:
- Auto Mode – The unit automatically chases through the different colors and built-in programs.
- Slave Mode – The unit is available to work by slave mode.
- DMX control mode – This function allows you to control each individual fixture’s traits with a standard DMX 512 controller.
- The sound control-This function allows you to activate fixtures by sound.
DMX Mode:
Operating through a DMX controller give the user the freedom to create their
own programs tailored to their own individual needs. This function also allows
you to use your fixtures as spotlights.
Chart Size(mm)
Touch Buttons: There are five buttons under the LCD display below:
Normally, the LCD will display the current DMX address code of the fixture,
as like, When the first line reads: “Select Menu<>”, press Menu to enter the
main menu; press Up/Down to scroll in the menu or submenu options; Press Enter
to confirm your selection, and the first line will change to “Select Value
DISPLAY MENU
DMX CHANNEL MODE
| Reduced Mode | Standard Mode | Value | Function |
|---|---|---|---|
| 1 | 1 | 000-255 | Master dimmer |
2
| ****
2
| 000-010| Off
011-110| Strobe fast-slow
111-115| Open
116-165| Pulse strobe1 slow-fast
166-170| Open
171-220| Pulse strobe 2 slow-fast
221-230| Open
231-245| Random strobe
246-266| Open
3| 3| 000-255| Pan
| 4| 000-255| Pan fine
4| 5| 000-255| Tilt
| 6| 000-255| Tilt fine
*| 7| 000-255| Pan/Tilt speed fast-slow
5| 8| 000-255| 15°-60° Zoom
6
| ****
9
| ****
207-255
191-206
184-190
180-183
179
175-178
174
172-173
168-171
162-167
157-161
151-156
149-150
147-148
146
145
142-144
138-141
137
134-135
131-133
129-130
128
127
126
| < Color Macro >
Alice Blue Congo Blue Dark Steel Blue Deep lavender Lilac Tint Daylight Blue Flame Red Bastard Amber Deep Orange Pale Gold Apricot
Bright Blue Primary Green Special lavender Pale Lavender
Deep Golden Amber Medium Blue
Bright Pink Mauve Dark Green Leaf Green Dark Blue Light Blue Steel Blue
Med Blue Green
| | 125
123-124
121-122
120
119
118
117
115-116
114
113
112
110-111
100-109
089-099
078-088
068-077
062-067
049-061
046-048
045
035-044
032-034
031
030
029
027-028
023-026
020-022
019
018
017
016
015
014
013
012
011
010
000-009
| Peacock Blue Magenta Dark Pink Middle Rose Light Salmon English Rose Light Rose Orange
Deep Amber Straw
Light Amber Spring Yellow Dark yellow green Just Blue
Sky Blue Lavender
Light Lavender Pink Carnation Medium Pink Light Pink Sunrise Red Dark Amber Gold Amber Medium Amber Fire
Surprise Peach Straw Tint Medium Yellow Black
White 5000°K White 3700°K White 7000°K Magenta Yellow
Cyan Blue Green Red
No function
---|---|---|---
7| 10| 000-255| CTO
8
| ****
11
| ****
133-255
010-132
000-009
| Built-in programs
Slow-Fast Fast->Slow
Open
9| 12| 000-255| Red color intensity
10| 13| 000-255| Green color intensity
11| 14| 000-255| Blue color intensity
12| 15| 000-255| White color intensity
---|---|---|---
13
| ****
16
| 072-255| No function
064-071| Backlight Off
056-063| Backlight On
010-055| Reset
000-009| No function
Rigging the fixture
Caution:
The fixture may cause severe injuries when crashing down! If you have doubts
concerning the safety of a possible installation, do not install the moving
head! Before rigging makes sure that the installation area can hold a minimum
point load of 10 times the fixture’s weight.
When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) in a distance of min. 1.0 m.
CAUTION!
Use an appropriate clamp to ring the fixture on the truss.
Follow the instructions mentioned at the bottom of the base. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.
- Securing the fixture via one safety wire
- Securing the fixture via two safety wires
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output.
- Use normal glass cleaner and a soft cloth to wipe down the outside casing.
- Clean the external optics with glass cleaner and a soft cloth every 20 days.
- Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).
TROUBLESHOOTING
Listed below are a few common problems the user may encounter, with solutions.
Replacing fuse
Only replace the fuse by a fuse of the same type and rating. Before replacing
the fuse, unplug mains lead!
If you need to replace the main fuse, follow the instructions:
- Remove the rear cover of the base by unscrewing 6 fastening screws.
- Remove the old fuse from the fuse holder.
- Install the new fuse into the fuse holder.
- Replace the rear cover back to the base.
The unit does not respond to DMX:
- Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 5 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Note:
All information is subject to change without prior notice.
Rua Chile, 678 São Bernardo do Campo SP – Brasil 09668-100 – Tel: +55 11 4368.8291 www.gobos.com.br. gobos@gobos.com.br.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>