GOBOS 041801 Moving Head Solar 17R Par no Case Instruction Manual

GOBOS 041801 Moving Head Solar 17R Par no Case

Unpacking: Thank you for purchasing Solar 17R. Every unit has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit have arrived intact. In the case, the damage has been found or parts are missing, please contact the manufacturer or your dealer for further instructions. Do not return this unit to your dealer without first contacting her.
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING THE FIXTURE. SAVE IT FOR FUTURE REFERENCE.

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

PLEASE consider that damages caused by manual modifications to the device are not subject to a warranty.

Caution! There are no user-serviceable parts inside this unit. Do not attempt any repairs yourself; doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact the manufacturer or your dealer.
PLEASE recycle the shipping carton whenever possible.
General Instructions: To optim11 the performance of this product, please read these operating instructions carefully to familial, you with the basic operations or! this unit. These instructions contain important safety information regarding the use and main! 11011 of 11111 unis!.

Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
• Do not spill water or other liquids into or onto your unit.
• Be sure that the local power outlet matches the required voltage for your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal shortage.
• Disconnect from the main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user-serviceable parts inside.
• Never operate this unit when it”s cover is removed.
• Never plug this unit into a dimmer pack.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6″ (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only; use of this product outdoors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in a safe and stable matter.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See “Cleaning” for details.
• Heal -The appliance should be situated away from heat· sources such as radiators, heat registers, stoves, or other appliances

(including amplifiers} that produce heat.
The fixture should be serviced by qualified service personnel when:

• A. The power-supply cord or the plug has been damaged.
• B. Objects have fallen, or liquid has been spilled into the appliance.
• C. The appliance has been exposed to rain or water.
• D. The appliance does not appear to operate normally or exhibit a marked change in performance.

Technical Specifications Electrical

• Power supply: ……. electronic auto-ranging
• Input voltage range …. supply 100-250V, 50/60Hz
• Power consumption …. 550W

Optic

• Light source: YOON HR! 350W Lamp
• LED life expectancy: 2200 hours
• Lens: High-precision optical lens
• Strobe: Dual lens strobe (0.5-9times/second} Dimmer; Smooth dimmer from 0-100%

Feature

• Color W110 I 13 color+white
• Rotating gobo wh I 12 gobos+ white
• Static gobo wheel. 17 fixed gobos+white Prism:12 -facets circular rotating prism Zoom: 2.5°-35°
• Focus: Linear adjustment

Motorized

• Payment
• Pan movement range: 540°
• n11 movement range: 270′
• 8biU16 bit movement solution, optional Automatic Panm1I position correction
• Pan movement o• -540°at max
• Tilt movement 0°-270°at max…

LCD operation

• Built-in demo sequences
• Silent fans cooling
• Strong two-phase motors
• Stand-alone operation
• Supported protocols: DMXS12
• 2 OMX modes (16/24 control channels)

Connection

• DMX data in/out: Locking 3-pin and 5-pin XLR AC power input: 1. Sm power cord with plug

Rigging

• Mounting points: 2 pairs of 1 /4-turn locks
• Mounting horizontally or vertically via 2 Omega brackets ·

Temperatures

• Maximum ambient temperature: 45 ‘C
• Maximum housing temperature: 75 ‘C

Minimum distances

• Min. distance from flammable surfaces: 3.0m
• Min. distance to lighted object: 2.0m
• Dimension: 386(L) x 365(W) x 589(H) mm
• Weight (net): 19kg
• Warranty: 1 Year

Set-Up:

• Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for the unit, The model is Auto power supply, and II is workable in 100-250V/50-60Hz. Please make sure your unit voltage matches the wall outlet voltage before attempting to operate your fixture.

Connection to the mains

• For protection from electric shock, the fixture must be earthed! Install a suitable plug on the power cord, note that the cores in the power cord are colored according to the following table. The earth has to be connected! If you have any doubts about proper installat1on, consult a qualified electrician.

DMX512 connection
The fixture is equipped with both 3-pin and 5-pin XLR sockets for OMX input and output. The sockets are wired in parallel Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.

• OMX oulpul
• XLR mounting sockets (rear view):
• OMX-input
• XLR mounting plugs (rear view):

OMX Linking: To ensure proper OMX data transmission, when using several OMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in an OMX line does not influence the OMX addressing. For example; a fixture assigned an OMX address of 1 may be placed anywhere in an OMX line, in the beginning, in the end, or anywhere in the middle. When a fixture is assigned an OMX address of 1, the OMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the OMX chain.
Building a serial OMX-chain:

Connect the OMX output of the first fixture in the OMX chain with the OMX input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.
Caution: Al the last fixture, the OMX-cable has to be terminated with a terminator. Solder a 1200 resistor between Signal (-) and Signal ( +) into a 3-pin XLR-plug and plug it in the OMX output of the last fixture.

Operating Modes: You can use the fixture in 4 ways:

• Auto Mode – The unit will automatically chase through the different colors and built-in programs.
• Slave Mode – The unit will run under slave mode.
• OMX control mode – This function will allow you to control each individual fixture’s traits with a standard OMX 512 controller.
• Sound control mode- When music play. The unit will work with music beats.
• OMX Mode : Operating through an OMX controller gives the user the freedom to create their own programs tailored to their own individual needs. This function also allows you to use your fixtures as spotlights.

1. This function will allow you to control each individual fixture’s traits with a standard OMX 512 controller.
2. The fixture has 16/24 two OMX channels to operate. Please see “OMX Values and Functions· for the OMX traits.
3. To run your fixture in OMX mode. plug in the fixture via the XLR connections to any standard OMX controller. Set your desired OMX address following the setup specifications that come with your OMX controller.

Hanging Drawing

CAUTION!

• Use an appropriate clamp to ring the fixture on the truss.
• Follow the instructions mentioned at the bottom of the base.
• Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.
• Securing the fixture via one safely wire
• Securing the fixture via two safety wires

1. Fixture
2. 0mega hokier
3. Clamp
4. Trust
5. Safety chain

Menu Map

DMX Chart

Dimension(mm)

Cleaning

1. Due to fog residue, smoke, and dust cleaning of the internal and external optical lenses must be carried out periodically to optimize light output.
2. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
3. Clean the external optics with glass cleaner and a soft cloth every 20 days.
4. Always be sure to dry all parts completely before plugging the unit back in.
5. Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, water)

TROUBLESHOOTING

1. Listed below are a few common problems the user may encounter, with solutions.

The unit does not respond to DMX

1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 5 may be ‘hot). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected

PLEASE Note: All information is subject to change without prentice

• Rua Chile, 678

• São Bernardo do Campo SP Brasil

• 09668-100 Tel: +55 11 4368.8291
  

• www.gobos.com. br –
  

• gobos@gobos.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>