lowes 5069596 Uolfin 5 Light Matte Gold 3 Light with Classic Candle Style Chandelier User Manual

lowes 5069596 Uolfin 5 Light Matte Gold 3 Light with Classic Candle Style

Chandelier

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

ACCESSORIES & QTY ENCLOSED

• (A) Wire connector (3)
• (B) Anchor (4)
• (C) Mounting screw (2)
• (D) Wood screw (4)

PARTS TYPE & QTY INCLUDING:

• (E) Mounting plate assembly (1)
• (F) Green ground screw (1)
• (G) Ball knob (2)
• (H) Canopy (1)
• (I) Loop (4)
• (J) Quick link (4)
• (K) Chain (2)
• (L) Iron tube (2)
• (M) Iron frame (1)
• (N) Socket (5)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre-installation

   • Step A1: Carefully pass the fixture wires through iron tubes (L), then screw iron tubes (L) onto iron frame (M).
   • Step A2: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
   • Step A3: Attach quick links (J) to chains (K) and loops (I) on canopy (H) and on the top of iron tubes (L). Carefully weave the fixture wires through chain (K) in and out of every other link and stop just when you reach the top of chain (K). Gently pull the wires to ensure the wires are not stressed.

3. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

4. Make installation

   • Step B1: Unscrew ball knobs (G) and carefully remove the mounting plate assembly (E).

   • Step B2: Carefully pass the supply wires from the outlet box through the mounting plate (E). To drill the holes on the wall for anchors (B), attach the mounting plate (E) to the outlet box with mounting screws (C) and mark the holes. Unscrew mounting screws (C) and remove mounting plate (E), drill holes and gently knock anchors (B) into the holes until anchors (B) are level with the wall. Secure mounting plate (E) to the outlet box with mounting screws (C) and wood screws (D).

   • Step B3: If needed, shorten the length of the fixture wires. At this point, the remaining wire length measured above the mounting plate assembly (E) is at least 6″.

   • Step B4: Make wire connections
     Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
     Connect ground wires according to the below chart
     Connect wires according to the below chart
     Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

   • Step B5: Raise canopy (H) to the ceiling and secure canopy (H) in place by tightening ball knobs (G) onto the pre-assembled mounting screws on mounting plate assembly (E).

   • Step B6: Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
     

5. Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

+1 850 296 2377 Working hours : Mon – Fri 9:00 a.m. – 16:00 p.m. EST uolfin@newdecorworld.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>