myenergi ZAPPI-DMPOST Zappi Dual Mounting Pedestal Installation Guide
- June 4, 2024
- Myenergi
Table of Contents
- myenergi ZAPPI-DM POST Zappi Dual Mounting Pedestal
- Product Overview
- Purpose of this document
- Warranty and Liability
- Safety
- Box contents
- Appearance
- Installation
- Maintenance, cleaning, and repair
- Decommissioning the pedestal
- Disposal
- Technical Data
- Technical Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
myenergi ZAPPI-DM POST Zappi Dual Mounting Pedestal
Product Overview
The zapping Pedestal is designed for mounting the zapping EV charger. It can accommodate either a single zapping or two zappers mounted back to back.
Purpose of this document
These installation instructions contain the information required to ensure correct and safe installation. These instructions should be read fully and understood before you begin installation and should be retained for the lifetime of the product.
Warranty and Liability
myenergi shall not assume liability for defects or damage that are the result of failing to follow the installation instructions. The liability exclusion particularly applies for:
- Installation by untrained personnel
- Improper use
- Repairs not carried out by myenergi
- Use of non-genuine parts
Safety
Intended use
This stand is intended for the mounting of the energy-zapping EV Charger(s) in
free space, independent of wall mounting. It should not be used to mount
anything other than the energy-zapping EV Charger(s). One pedestal can mount
up to two zappy chargers, one on either side.
Qualifications of installation personnel
These installation instructions are intended for suitably qualified
installation personnel only.
General safety information
The pedestal for the myenergi zappy EV Charger(s) has been developed,
produced, tested, and documented according to the relevant safety and
environmental requirements and regulations. For electrical safety information
refer to the zapping EV Charger specific instructions. Ensure only persons who
have read these instructions have access to the pedestal.
Box contents
- 1nr zappi Pedestal
- 6nr M6 x 25 Button Head Socket Screws (3nr per side Come as part of pedestal)
- 2nr grommets (1nr per side)
- 1nr Installation Guide
Appearance
Installation
Observe the safety information provided in section 4. In addition to these installation instructions follow and comply with the local regulations relating to the operation, installation, and environmental protection. Install the pedestal only in combination with the application of the Operating and Installation instructions of the myenergi zappy Pedestal
Required tools / Materials
Tool
Description
Suitable 10mm Fixings (To be determined by installer based on substrate depth
etc.)| For fixing base plate to concrete substrate.
---|---
4mm Allen Key/Hex Key| For mounting of the zappi EV charging
station.
Cabling tools| For making all connections
General tools, drills, etc.| For mounting the pedestal.
Suitable 10mm Fixings (To be determined by the installer based on substrate depth etc.) 4mm Allen Key/Hex Key Cabling tools General tools, drill, etc. For fixing the base plate to the concrete substrate. For mounting of the zappi EV charging station. For making all connections For mounting of the pedestal.
Location requirements
- If a pedestal is installed in close proximity to a road or public parking place an adequate collision barrier/guard/protector must be installed.
- Should you install more than one pedestal in the same location you should ensure there is at least a 200mm gap between the two.
- The surface you are mounting to should be fully level and flat.
Mounting base
- It is the responsibility of the installer to ensure the base for mounting the stand is of a suitable build-up and thickness and the fixings used to secure the pedestal are adequate enough for the substrate you are mounting to.
General;
- The electrical supply cables must come out of the concrete at the center of the pedestal’s baseplate and have an excess of at least 1500mm
Step-by-step instructions
These instructions are for the installation of the pedestal only and should be
read in conjunction with the zappi operation and installation manual.
- Step 1: Remove from box and recycle packaging.
- Step 2: Remove rubber grommet as necessary on the side you will be mounting your zappi(s) and slice down the center line to create an opening.
- Step 3: Feed cable through the base plate and up the pedestal to the hole and through the grommet.
- Step 4: Fix base plate of pedestal down to substrate using fixings suitable for thickness and material, as necessary.
- Step 5: Remove screws from the head of the pedestal and keep them safe for later use.
- Step 6: Refer to mounting instructions in “zappi Operation and Installation Manual”.
Note: Use screws supplied with pedestal. Use washers supplied with zappi charger. Step 7: Make electrical connection as per instructions in “zappi Operation and Installation Manual”.
Maintenance, cleaning, and repair
Maintenance
The pedestal does not require any maintenance.
Cleaning
DANGER High voltages Danger of fatal electric shock Never clean the pedestal
with a high-pressure cleaner or similar device.
-
Clean the installation only with a dry cloth. Do not use aggressive cleaning agents, wax, or solvents.
NOTE -
Do not use alkaline cleaning agents. Alkaline cleaning agents can cause a discoloring of the pedestal. b Tree resin could also cause discoloration.
Repair
Unauthorized repair of this pedestal is not permitted.
Decommissioning the pedestal
- In case the pedestal is to be decommissioned it should be carried out by an authorized electrician.
- Decommission the charging station(s) in accordance with the “zappi Operation and Installation Manual”.
- Dismantle the pedestal. b Dispose of the pedestal in accordance with the national regulations.
Disposal
- Dispose of packaging in the corresponding recycling container in accordance with national regulations.
Technical Data
Specification | Details |
---|---|
Weight (kg) | 8.3kg |
Material | Aluminum |
Corrosion Protection | Powder coated |
Colour | RAL 9005 (Black) |
Dimensions | See figures 1 and 2 below |
Technical Support
If you experience any issues during or pedestal set-up, please contact our technical support team by scanning the QR Code below. https://myenergi.com /manual-support/ Please contact us directly for the quickest solution.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>