SDI TECHNOLOGIES B54A Bluetooth Headphones User Manual

June 3, 2024
Sdi Technologies

SDI TECHNOLOGIES B54A Bluetooth Headphones

Wireless Headphones

CHARGE BEFORE USE

SDI-TECHNOLOGIES-B54A-Bluetooth-Headphones-FIG-1

CHARGING THE HEADPHONES

MUST ALWAYS BE CONDUCTED BY AN ADULTSDI-TECHNOLOGIES-B54A-Bluetooth-
Headphones-FIG-2

POWER ON/OFF

  • Press and hold the Power/MFB Button for 3 seconds to turn headphones ON.
  • Press and hold the Power/MFB Button for 5 seconds to turn OFF.

BLUETOOTH PAIRING

MUST ALWAYS BE CONDUCTED BY AN ADULT

  • When the headphones are powered ON, they will automatically enter pairing mode.
  • Select ‘ekids B54’ on your Bluetooth-enabled device to connect.
  • Once paired, the headphones will automatically try to connect to the most recent connected device. To manually pair, when headphones are ON, press and hold the + and
  • Buttons at the same time for 3 seconds to enter pairing mode. To reset Bluetooth, press and hold the + and – Buttons at the same time for 7 seconds.

CONTROLS

  • Short press Power/MFB Button to play/pause audio.
  • Double press + Button to skip to next track / double press – Button for previous track.
  • Short press + Button to turn the volume up one step. Press and hold to ramp up volume.
  • Short press – Button to turn volume down one step. Press and hold to ramp down volume.
  • Short press Power/MFB Button to answer or end a call.
  • Press and hold Power/MFB Button to decline an incoming call. When a call is in progress, press and hold Power/MFB Button for 2 seconds to transfer between phone/headphones.
    Note : Once headphone are paired, they will auto power off after 60 min of no audio activity. If the headphones are not paired, the unit will power off after 3 minutes.

AUDIO CABLE (included with select models)

  • Use a 3.5mm audio cable for optional wired listening. (Please use adult supervision when using an audio cable, greater than 300mm (12 in) for wired listening.)

LED INDICATOR

  • LED flashes red/blue while in Bluetooth pairing mode, and flashes blue when connected. A voice prompt will alert you when the battery is low. The LED glows solid red while charging, and turns OFF when the headphones are fully charged.

ONE YEAR LIMITED WARRANTY – For product support and warranty please visit: www.ekids.com/support

To prevent possible hearing damage, do not listen at high volume levels for long periods.

WARNING: For your safety, do not use headphones if they would prevent you from hearing warning sounds, such as while riding a bike, crossing the street, etc.

I MPORTANT SAFETY INSTRUCTIONS

Please heed all warnings, read and follow all instructions and keep these instructions handy for future reference. Do not use or charge this product near a water source, and clean only with dry cloth. Do not block any ventilation openings. Keep product away from heat sources. Only use an UL/ETL certified charging adapter (not included), and the supplied USB charging cable. Never leave unattended when charging.

GENERAL BATTERY PRECAUTIONS

Never use or charge a battery if it appears to be leaking, or in any way abnormal. Avoid charging battery when the temperature is not within 5°C – 35° C (41° – 95° Fahrenheit). Never expose a battery to any liquid, or to excessive heat such as direct sunlight or fire. Never leave in an unventilated vehicle where excessive internal temperatures may be encountered. Always keep batteries out of the reach of infants and small children. Always charge lithium devices on a non-flammable surface – wooden tables/ carpeted floors are not recommended charging surfaces. If the unit is to be unused for an extended period of time, such as a month or longer, charge the unit fully before storage.

WARNING/DISPOSAL OF UNIT – Do NOT attempt to change or disassemble the built-in battery. Doing so will void the warranty and could cause personal injury and damage to your device. Do not dispose of batteries in the household trash or fire. Always dispose of used batteries/electronics in accordance with the prevailing community regulations. To find a drop-off location near you, visit www.call2recycle.

THIS IS NOT A TOY.

FCC Information

FCC ID: EMOB54A
IC: 986B-B54A
HVIN : B54a

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3 (B) / NMB-3(B)
ISED statements
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device. This device comply with ISED RF exposure requirement, users can obtain Canadian information on RF exposure and compliance.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
©2022 All Rights Reserved. Questions? Visit www.ekids.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals