SDI TECHNOLOGIES B38 Series Wireless Headphones User Manual
- June 9, 2024
- Sdi Technologies
Table of Contents
SDI TECHNOLOGIES B38 Series Wireless Headphones
CHARGE BEFORE USE
**CHARGING THE HEADPHONES – MUST ALWAYS BE CONDUCTED BY AN ADULT
**
POWER ON/OFF
- Press and hold the Multi-Function Button (MFB) for 2 seconds to turn headphones ON.
- Press and hold the Multi-Function Button (MFB) for 3 seconds to turn OFF.
VOLUME SWITCH
- Use the volume switch to select High, Medium, or Low. The unit is factory set to Low, which is the recommended listening level.
BLUETOOTH PAIRING – MUST ALWAYS BE CONDUCTED BY AN ADULT
- When the headphones are ON, they will automatically enter pairing mode.
- Select ‘ek-B38VM’ on your Bluetooth-enabled device to connect.
- Headphones will automatically connect to your Bluetooth device whenever it is in range. To manually pair, press and hold the MFB for 5 seconds to enter pairing mode. To reset Bluetooth, press the MFB 3 times while in pairing mode.
CONTROLS
- Short press the MFB to play/pause audio.
- Use Next/Previous Track Buttons to navigate tracks.
- Short press the MFB to answer/end an incoming phone call.
- Press and hold the MFB for 2 seconds to reject an incoming phone call.
- Press and hold the MFB for 2 seconds to access Siri/Google Assistant.
Note: Headphones will automatically power OFF after 15 minutes of no activity.
AUX CABLE
- Use a 3.5mm aux cable (not included) for optional wired listening. (Please use adult supervision when using an aux cable, greater than 300mm (12 in) for wired listening.)
LED INDICATORS
- LED flashes red/blue while in Bluetooth pairing mode, and flashes blue when connected.
- LED flashes red when battery is low, glows solid red while charging, and turns solid blue when the headphones are fully charged.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
FCC Information
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B) / NMB-3(B)
ISED statements
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device. This device comply with ISED RF exposure requirement, users can obtain Canadian information on RF exposure and compliance.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING: For your safety, do not use headphones if they would prevent you
from hearing warning sounds, such as while riding a bike, crossing the street,
etc.
IMPORTANT SAFETY INSTRUCTIONS – Do not use or charge this product near a
water source, and clean only with dry cloth. Do not block any ventilation
openings. Keep product away from heat sources. Only use accessories specified
by the manufacturer. Never leave unattended when charging.
GENERAL BATTERY PRECAUTIONS – Never use or charge a battery if it appears
to be leaking, or in any way abnormal. Avoid charging battery when the
temperature is not within 5°C – 35° C (41° – 95° Fahrenheit). Never expose a
battery to any liquid, or to excessive heat such as direct sunlight or fire.
Always keep batteries out of the reach of infants and small children. Always
charge lithium devices on a non-flammable surface – wooden tables/ carpeted
floors are not recommended charging surfaces.
WARNING/DISPOSAL OF UNIT – Do NOT attempt to change or disassemble the
built-in battery. Doing so will void the warranty and could cause personal
injury and damage to your device. Do not dispose of batteries in the household
trash or fire. Always dispose of used batteries/electronics in accordance with
the prevailing community regulations. To find a drop-off location near you,
visit www.call2recycle.com
THIS IS NOT A TOY.
Documents / Resources
| SDI
TECHNOLOGIES B38 Series Wireless
Headphones
[pdf] User Manual
B38A, EMOB38A, B38 Series Wireless Headphones, B38 Series, Wireless
Headphones, Headphones
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>