Surenoo STP0144E-128128 Series TFT LCD Panel User Manual

June 3, 2024
Surenoo

STP0144E-128128 Series TFT LCD Panel
User Manual

STP0144E-128128 Series TFT LCD Panel

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
STP0144E-128128 Series
TFT LCD PANEL USER MANUAL
Please click the following image to buy the sampleSurenoo STP0144E-128128
Series TFT LCD Panel fig 1 Potter Hao Surenoo Technology 0086-17820607849 info@surenoo.com http://www.surenoo.com

http://qr.kakao.com/talk/THom9tzJN5OMzvx1vTL1V.LvnEc-
https://wa.me/qr/4GGOIDYZ2PXXN1https://line.me/ti/p/oas8BmVLVd
https://u.wechat.com/EAK0B_l2YfPLwx3tRqiKkf4

Shenzhen Surenoo Technology Co.,Ltd.
www.surenoo.com
Skype: Surenoo365
Reference Controller Datasheet
TFT LCD Panel Selection Guide
GC9106

REV NO. REV DATE CONTENTS REMARKS
V0 2021-9-8 First release Preliminary

GENERAL INFORMATION

Item Contents Unit
LCD Type TFT/TRANSMISSIVE
Viewing Direction Free O’Clock
Outline Dimensions (W ´ H´T) 29.5(W ) ×36.5 (H)×2.45(T) mm
Viewing area 26.1×27.1 mm
Active area 25.5(W) x26.5(H) mm
Number of Dots 128RGB x 128 Dots
Pixel pitch (W ´ H) 0.153*0.153 mm
Driver IC CTC+GC9106
Interface Type MCU8
Input voltage 2.8V
Module Power consumption TBD MW
Colors 262K
Backlight Type LED

Surenoo STP0144E-128128 Series TFT LCD Panel fig 2

ABSOLUTE MAXIMUM RATINGS

Item Symbol Min Max Unit
Supply voltage for logic VDD -0.3 4.6 V
Input voltage VIN -0.3 VDD+ 0.3 V
Operating temperature TOP -20 70
Storage temperature TST -30 80
Humidity RH 90%(Max60 °C) RH

ELECTRICAL CHARACTERISTICS

Item Symbol Min Typ Max Unit
Supply voltage for logic VDD 2.7 2.8 2.9 V
Input Current Idd TBD TBD mA
Input voltage ‘H’ level VIH 0.7VDD VDD V
Input voltage ‘L’ level VIL VSS 0.3VDD V
Output voltage ‘H’ level VOH 0.8VDD VDD V
Output voltage ‘L’ level VOL VSS 0.2VDD V

BACKLIGHT CHARACTERISTICS

Item Symbol Min Typ Max Unit Condition
Forward voltage Vf 3.0 3.2 3.4 V If=2*20mA
Number of LED      LED 2 Piece
Connection mode P Parallel

Using condition: constant current driving method If=40mA(+/-10%).

ELECTRO-OPTICAL CHARACTERISTICS

Parameter Symbol Values Unit Notes
Min Typ Max
Transmittance(LCM) T(%) 5
Contrast Ratio (LCM) C/R 150
Response Time (TFT) Tr+Tf 50
Surface Luminance (LCM) Iv 100
CIE Color Coordinate (LCM) Rx 0.5156 0.5656 0.6156
Ry 0.2620 0.3120 0.3620
Gx 0.2714 0.3214 0.3714
Gy 0.5400 0.5900 0.6400
Bx 0.0946 0.1446 0.1946
By 0.0415 0.0915 0.1415
Wx 0.23 0.26 0.29
Wy 0.26 0.29 0.32
Viewing Angle (TFT) θl 45
θr 45
θu 35
θd 15

INTERFACE DESCRIPTION

Note: The voltage power of the interface logic pin depend on IOVCC and GND, Such as DBn, IMn and function pins

PIn.NO. Name
1 LED-K
2 LED-A
3 GND
4 VDD2.8V
5 10VCC41.8/2.8V)
6 NC
7 /CS
8 /RESET
9 RS
10 AIR
11 /RD
12 DB7
13 DB6
14 DB5
15 DB4
16 DB3
17 DB2
18 DB1
19 DBO
20 GND

REFERENCE APPLICATION CIRCUIT

Please consult our technical department for detail information.

RELIABILITY TEST CONDITIONS

No. Test Item Test condition Inspection after test
1 High Temperature Storage 80℃±2℃ 96H Inspection after 2~4hours storage at

room temperature,the sample shall be free from defects:
2| Low Temperature Storage| -30℃±2℃ 96H|
---|---|---|---
3| High Temperature Operation| 70℃±2℃ 48H
4| Low Temperature Operation| -20℃±2℃ 48H
5| High Temperature/Humidity Storage| 60℃±2℃ 90%RH 48H
6| Temperature Cycle| -30℃: 30min
:70℃: 30min
7| Vibration Test (package state)| 10Hz~55Hz~10Hz, X/Y/Z| Not allowed cosmetic and electrical defects.
8| Dropping test

| 08m     LCD≥3.0inch

INSPECTION CRITERION

PRECAUTIONS FOR USE OF LCD MODULES

11.1 Handling Precautions
11.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc.
11.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water.
11.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary.
11.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully.
11.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents:
— Isopropyl alcohol
— Ethyl alcohol
Solvents other than those mentioned above may damage the polarizer.
Especially, do not use the following:
— Water
— Ketone
— Aromatic solvents
11.1.6 Do not attempt to disassemble the LCD Module.
11.1.7 If the logic circuit power is off, do not apply the input signals.
11.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment.
a. Be sure to ground the body when handling the LCD Modules.
b. Tools required for assembly, such as soldering irons, must be properly ground.
c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions.
d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated.
1.2 Storage precautions
11.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps.
11.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is:

Temperature : 0℃ ~ 40℃
Relatively humidity: ≤80%

11.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas.
11.3.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.

www.surenoo.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals