Surenoo Technology SLC1602I Series LCD Module User Manual Shenzhen Surenoo Technology Co.,Ltd. LCD Module
- October 30, 2023
- Surenoo Technology
Table of Contents
SLC1602I Series LCD Module
Shenzhen Surenoo Technology Co.,Ltd. LCD Module
Model No.: 3ASLC1602I
Reference Controller Datasheet: ST7032
Character LCD Selection Guide: Page 01 of 20
Website: www.surenoo.com
Skype: Surenoo365
Contents
- Ordering Information
- 1602I Series Table
- Specification
- Display Specification
- Mechanical Specification
- Electrical Specification
- Optical Specification
- Outline Drawing
- Electrical Spec
- Pin Configuration
- Absolute Maximum Ratings
- Electrical Characteristics
- Inspection Criteria
- Acceptable Quality Level
- Definition of Lot
- Condition of Cosmetic Inspection
- Module Cosmetic Criteria
- Screen Cosmetic Criteria (Non-Operating)
- Screen Cosmetic Criteria (Operating)
Product Usage Instructions
-
Refer to the ordering information table to select the
appropriate model number for your LCD module. -
Refer to the specification section to understand the technical
details of the LCD module, including display, mechanical,
electrical, and optical specifications. -
Refer to the outline drawing section to understand the physical
dimensions of the LCD module. -
Refer to the electrical spec section to understand the pin
configuration, absolute maximum ratings, and electrical
characteristics of the LCD module. -
Refer to the inspection criteria section to understand the
acceptable quality level, definition of lot, and cosmetic criteria
for the LCD module and screen.
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
SLC1602I Series
LCD MODULE USER MANUAL
Please click the following image to buy the sample
Model No.:3ASLC1602I
www.surenoo.com
Shenzhen Surenoo Technology Co.,Ltd. www.surenoo.com Skype: Surenoo365
Reference Controller Datasheet
Character LCD Selection Guide
ST7032
Page: 01 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
CONTENTS
15B0H
1. ORDERING INFORMATION – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 04
18BH
U
1.1 1602I Series Table- – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
04
19B4H
H
1.2 1602I Series Image- – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
05
20B15H
H21B
2. SPECIFICATION – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 06
21B8HU
U
2.1 Display Specification- – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 06
2B194H
2.2 Mechanical Specification – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – 06
23B015H
2.3 Electrical Specification – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 06
24B1H
H
2.4 Optical Specification – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 06
25B1H
3. OUTLINE DRAWING- – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 07
26B31HU
U
4. ELECTRICAL SPEC – – — – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 08
21B8HU
U
4.1 Pin Configuration – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 08
2B194H
4.2 Absolute Maximum Ratings – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 09
23B015H
H
4.3 Electrical Characteristics – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 09
24B1H
H H
5. INSPECTION CRITERIA – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – 10
H31B2869
5.1 Acceptable Quality Level – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 10
32B970H
H
5.2 Definition of Lot – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 10
3B0281H
H
5.3 Condition of Cosmetic Inspection – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 10
34B129H
H
5.4 Module Cosmetic Criteria – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – 11
35B204H
5.5 Screen Cosmetic Criteria (Non-Operating) – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 13
36B14H
H
5.6 Screen Cosmetic Criteria (Operating) – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 14
37B42H
H
6. PRECAUTIONS FOR USING – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – 16
38B54H
6.1 Handling Precautions – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – 16
39B641H
6.2 Power Supply Precautions- – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – 17
40B3752H
6.3 Operating Precautions – – – – – – – – – – – – – – – – – – — – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – 17
41B386H
6.4 Mechanical/Environmental Precautions – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – 17
42B397H
6.5 Storage Precautions – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – 17
43B08H
6.6 Others – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 17
4B139H
45B20H
www.surenoo.com
Page: 02 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
7. USING LCD MODULES – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 18 H
7.1 Liquid Crystal Display Modules – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – 18
46B31H
7.2 Installing LCD Modules – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 18
47B2H
H
7.3 Precaution for Handling SUR Modules – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – 19
48B53H
7.4 Electro-Static Discharge Control- – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – 19
49B6H
7.5 Precaution for Soldering to LCM- – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
19
50B47H
7.6 Precaution for Operation – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 20
51B486H
H
7.7 Limited Warranty – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 20
52B497H
H
7.8 Return Policy – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – 20
53B048H
TEST CODE – – – – – – – – – – – – – – – – – – —— – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – —- – – – – I1-I4 53B048H
www.surenoo.com
Page: 03 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
1. ORDERING INFORMATION
54B197
1.1 SLC1602I Series Table
Model No.
SLC1602I
Interface
SPI
Display
16*02
Outline Size Viewing Area Area Area
(MM)
(MM)
(MM)
Without PCB
41.50*24.30 Without PCB
37.60*13.80
41.50*33.30
34.21*8.76
Voltage (V) 3.3V
Controller Mark Color Code
ST7032S or Equal
1602I1 Without PCB
1602I2 With PCB
IMAGE
www.surenoo.com
Page: 04 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
1.2 SLC1602I Series Image *The number of series image is in accordance with number of the above series table 1.1.
www.surenoo.com
Page: 05 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
2. SPECIFICATION
58B214039
2.1 Display Specification
40B59376
ITEM
60B574
Resolution
63B057
Display Connector
6B308
Operating Temperature
70B648
Storage Temperature
73B0689
Touch Panel Optional Font Chip Optional
82B796
*Sunlight Readable
82B796
2.2 Mechanical Specification ITEM
86B30
Outline Dimension
89B63
Visual Area
92B86
Active Area
94B18
Character Size Dot Size
96B308
Dot Pitch
9B63
Net Weight
102B96
2.3 Electrical Specification ITEM
106B3
IC Package
109B637
Controller
12B0967
Interface
15B209
2.4 Optical Specification ITEM
19B63
LCD Type
12B9653
Backlight Color
125B96
Viewing Direction
128B56
LCD Duty
13B2856
LCD Bias
134B2859
STANDARD VALUE
61B584
16 Characters x 2 Lines
64B158
I1:10P-1.5-Pin / I2: 8P-2.54-Pin
67B419
-20 ~ +70
71B685
-30 ~ +80
74B16890
N/A N/A
83B07
UNIT
62B594
—
65B29
—
68B5270
72B698
75B2691
—
81B75
—
84B17
STANDARD VALUE
87B41
I1: 41.5(W) ×24.3(H) × 3.9(T) (MAX) / I2: 41.5(W) ×33.3(H) × 4.9(T) (MAX)
90B874
37.60(W) × 13.80(H) 34.21(W) × 8.76(H) 1.81(W) × 4.13(H) 0.33 × 0.49
97B418
0.37 × 0.52
10B974
20.0 ± 15% grams (typical)
103B97
UNIT
8B52
mm
91B85
mm
93B087
mm
95B28
mm mm
98B52
mm
10B985
g
104B98
STANDARD VALUE
107B4
COG
10B742
ST7032S or Equal
13B072
Serial SPI
16B309
UNIT
108B52
—
1B085
—
14B08
—
17B4
STANDARD VALUE
120B74
Refer to 1.1 SLC1602I Series Table
123B0754
Refer to 1.1 SLC1602I Series Table
126B30
6:00
129B63
1/16
132B9657
1/5
135B2960
UNIT
12B85
—
124B85
—
127B46
Clock
130B2746
Duty
13B02758
Bias
136B0
www.surenoo.com
Page: 06 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
3. OUTLINE DRAWING
459B1376
SLC1602I1(Without PCB Adapter)
Model No.:3ASLC1602I
SLC1602I2(With PCB Adapter)
www.surenoo.com
Page: 07 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
4. ELECTRICAL SPEC
4.1 Pin Configuration
48B139562
SLC1602I1(Without PCB Adapter)
Pin No 1 2
Pin Name XV0S V0S
Descriptions Bias Voltage (Insert 1uF Capacitor between them)
3
VGS
Bias Voltage (Insert 1uF Capacitor between VGS and VDD)
4
VDD
Logic Power Supply, +3.3V
5
VSS
Ground ,0V
6
D7(SDA) Serial Data
7
D6(SCLK) Serial Clock
8
CSB
Chip Selection
9
A0(RS) Register Selection Signal (H: Data Register; O: Command Register)
10
RSTB
Reset Pin
SLC1602I2(With PCB Adapter)
Pin No 1
Pin Name LEDA
Descriptions Backlight Power Supply, +3.3V
2
VSS
Ground ,0V
3
VDD
Logic Power Supply, +3.3V
4
A0(RS) Register Selection Signal (H: Data Register; O: Command Register)
5
RSTB
Reset Pin
6
CSB
Chip Selection
7
SCLK
Serial Clock
8
SDA
Serial Data
Model No.:3ASLC1602I
www.surenoo.com
Page: 08 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
4.2 MAXIMUM ABSOLUTE LIMIT (Ta =25°C) White LED Backlight(2PCS LEDs) 3.0V (16-30mA)
4.2.1
VDD – VSS -0.3
3.3
LCD
V0-XV0
-0.3
5.1
LCD
VG
-0.3
-20
-30
3.6 7 4 +70 +80
V V V
4.2.2 DC
VDD VLED VIHC VILC VOHC VOHC
IDD ILED
IOH = 0.2mA IO0 = 1.2mA VDD = 3.0V VLED=3.0V
MIN
TYPE MAX
2.7
3.3 4.5
2.9
3.0 3.1
0.8xVDD –
VDD
VSS –
0.2xVDD
0.8xVDD –
VDD
VSS –
0.2xVDD
–
0.3
16
20
30
V V V V V V mA mA
www.surenoo.com
Page: 09 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
5. INSPECTION CRITERIA
286B3094
5.1 Acceptable Quality Level
H287B4130
Each lot should satisfy the quality level defined as follows
28B5
PARTITION
289B63
A. Major
29B86
B. Minor
295B8
AQL
290B874
0.4%
293B087
1.5%
296B30
DEFINITION
291B85
Functional defective as product
294B18
Satisfy all functions as product but not satisfy cosmetic stanard
297B41
5.2 Definition of Lot
298B5436
One lot means the delivery quantity to customer at one time.
29B63
5.3 Condition of Cosmetic Inspection INSPECTION AND TEST
301B2985
-FUNCTION TEST
302B96
-APPEARANCE INSPECTION
30B297
-PACKING SPECIFICTION
304B1298
INSPECTION CONDITION
305B29
– Put under the lamp (20w¡Á2) at a distance 100mm from
306B
– Tilt upright 45 degree by the front (back) to inspect LCD appearance.
307B41
AQL INSPECTION LEVEL
308B52
– SAMPLING METHOD: MIL-STD-105D
309B6
– SAMPLING PLAN: SINGLE
310B74
– MAJOR DEFECT: 0.4% (MAJOR)
31B085
– MINOR DEFECT: 1.5% (MINOR)
312B096
– GENERAL LEVEL: II/NORMAL
31B07
www.surenoo.com
Page: 10 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
5.4 Module Cosmetic Criteria
438B15209
NO.
Item
Judgment Criterion
1 Difference in Spec.
None allowed
2 Pattern Peeling
No substrate pattern peeling and floating
3 Soldering defects
No soldering missing
No soldering bridge
No cold soldering
4 Resist flaw on substrate Invisible copper foil(0.5mm or more)on substrate pattern
5 Accretion of metallic
No soldering dust
Foreign matter
No accretion of metallic foreign matters(Not exceed0.2mm)
6 Stain
No stain to spoil cosmetic badly
7 Plate discoloring
No plate fading,rusting and discoloring
8 Solder amount
a. Soldering side of PCB
1.Lead parts
Solder to form a’Filet’ all around the lead. Solder should not hide the lead form perfectly.(too much) b.Components side (In case of `Through Hole PCB’)
Solder to reach the Components side of PCB
Partition Major Major Major Major Minor Minor Minor
Minor Minor Minor
2.Flat packages
Either toe'(A) orheal’ (B) of
the lead to be covered by `Filet’.
A
B
Lead form to be assume over Solder.
Minor
3.Chips
(3/2) Hh(1/2)H
h
H
Minor
www.surenoo.com
Page: 11 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
9 Backlight defects 10 PCB defects 11 Soldering defects
1.Light fails or flickers.(Major) 2. Color and luminance do not correspond to
specifications.
(Major) 3.Exceeds standards for display’s blemishes, foreign matter,
dark lines or scratches.(Minor)
Oxidation or contamination on connectors. 2. Wrong parts, missing parts, or
parts not in specification. 3.Jumpers set incorrectly.(Minor) 4.Solder(if
any)on bezel,LED pad,zebra pad,or screw hole
pad is not smooth.(Minor) Minor if display functions correctly.Major if the
display fails.
1. Unmelted solder paste. 2. Cold solder joints,missing solder connections,or
oxidation. 3. Solder bridges causing short circuits. 4. Residue or solder
balls. 5. Solder flux is black or brown. Minor if display functions
correctly.Major if the display fails.
See list
See list
Minor
www.surenoo.com
Page: 12 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
5.5 Screen Cosmetic Criteria (Non-Operating)
No. Defect
1 Spots 2 Lines 3 Bubbles
Polarizer
Judgment Criterion
In accordance with Screen Cosmetic Criteria (Operating) No.1.
In accordance with Screen Cosmetic Criteria (Operation) No.2.
in
Size: d mm
Acceptable Qty in active area
d0.3
Disregard
0.3<d1.0
3
1.0<d1.5
1
1.5<d
0
Partition
Minor Minor Minor
4 Scratch
In accordance with spots and lines operating cosmetic criteria, When the Minor
light reflects on the panel surface, the scratches are not to be remarkable.
5 Allowable density Above defects should be separated more than 30mm each other.
Minor
6 Coloration
Not to be noticeable coloration in the viewing area of the LCD panels.
Minor
Back-lit type should be judged with back-lit on state only.
7 Contamination
Not to be noticeable.
Minor
www.surenoo.com
Page: 13 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
5.6 Screen Cosmetic Criteria (Operating)
No.
Defect
1 Spots
A) Clear
Judgment Criterion
Size:d mm d0.1
0.1<d0.2 0.2<d0.3
0.3<d
Acceptable Qty in active area Disregard 6 2 0
Partition Minor
Note: Including pin holes and defective dots which must be within one pixel Size. B) Unclear
Size:d mm d0.2
0.2<d0.5 0.5<d0.7
0.7<d
Acceptable Qty in active area Disregard 6 2 0
2 Lines
A) Clear
Minor
L 5.0 2.0
8
(0) (6)
0.02 0.05
0.1
Note: () Acceptable Qty in active area L – Length (mm) W -Width(mm)
-Disregard
B) Unclear
8
L 10.0 (6)
2.0 0.05
(0) 0.3
See No.1 W
See No.1 W
0.5
Clear’ = The shade and size are not changed by Vo.Unclear’ = The shade and
size are changed by Vo.
www.surenoo.com
Page: 14 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
No.
Defect
Judgment Criterion
3 Rubbing line
Not to be noticeable.
4 Allowable density Above defects should be separated more than 10mm each other.
5 Rainbow
Not to be noticeable.
6 Dot size
To be 95%~105%of the dot size (Typ.) in drawing.
Partial defects of each dot (ex.pin-hole) should be treated as’spot’.
(see Screen Cosmetic Criteria (Operating) No.1)
7 Brightness (only back-lit Module)
Brightness Uniformity must be BMAX/BMIN2 – BMAX :Max.value by measure in 5 points – BMIN : Min.value by measure in 5 points Divide active area into 4 vertically and horizontally. Measure 5 points shown in the following figure.
Partition
Minor Minor Minor
Minor
8 Contrast Uniformity
Contrast Uniformity must be BmAX/BMIN2 Measure 5 points shown in the following figure. Dashed lines divide active area into 4 vertically and horizontally. Measuring points are located at the inter-sections of dashed line.
Minor
Note: BMAX Max.value by measure in 5 points. BMIN Min.value by measure in
5 points. O Measuring points in 10mm.
Note: (1) Size : d=(long length + short length)/2 (2) The limit samples for
each item have priority. (3) Complexed defects are defined item by item, but
if the number of defects is defined in above table, the total number should
not exceed 10.
www.surenoo.com
Page: 15 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
(4) In case of concentration’, even the spots or the lines ofdisregarded’
size should not be allowed. Following three situations Should be treated as
`concentration’.
-7 or over defects in circle of 5mm. -10 or over defects in circle of 10mm -20 or over defects in circle of 20mm
6. PRECAUTIONS FOR USING
319B6452
HED 6.1 Handling Precautions H320B17458 H This device is susceptible to
Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions. 321B85
SUR display panel is made of glass. Do not subject it to a mechanical shock by
dropping it or impact. If 32B196 SUR display panel is damaged and the liquid
crystal substance leaks out, be sure not to get any in your 32B017 mouth. If
the substance contacts your skin or clothes, wash it off using soap and water.
Do not apply excessive force to the SUR display surface or the adjoining areas
since this may cause the 324B18 color tone to vary. The polarizer covering the
SUR display surface of the LCD module is soft and easily scratched. Handle
this 325B19 polarizer carefully. If SUR display surface becomes contaminated,
breathe on the surface and gently wipe it with a soft dry 326B0 cloth. If it
is heavily contaminated, moisten cloth with one of the following Isopropyl or
alcohol. Solvents other than those above-mentioned may damage the polarizer.
Especially, do not use the Water. 327B41 Exercise care to minimize corrosion
of the electrode. Corrosion of the electrodes is accelerated by water 328B5
droplets, moisture condensation or a current flow in a high-humidity
environment. Install the SUR LCD Module by using the mounting holes. When
mounting the LCD module make 329B6 sure it is free of twisting, warping and
distortion. In particular, do not forcibly pull or bend the cable or the
backlight cable. Do not attempt to disassemble or process SUR LCD module.
30B274 NC terminal should be open. Do not connect anything. 31B285 If the
logic circuit power is off, do not apply the input signals. 32B96 To prevent
destruction of the elements by static electricity, be careful to maintain an
optimum work 3B027 environment. -Be sure to ground the body when handling SUR
LCD modules. 34B128 -Tools required for assembling, such as soldering irons,
must be properly grounded. 35B29 -To reduce the amount of static electricity
generated, do not conduct assembling and other work under dry 36B0 conditions.
-The LCD module is coated with a film to protect the display surface. Exercise
care when peeling off this 37B41 protective film since static electricity may
be generated.
www.surenoo.com
Page: 16 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
6.2 Power Supply Precautions Identify and, at all times, observe absolute
maximum ratings for both logic and LC drivers. Note that there is
38B524619
some variance between models. Prevent the application of reverse polarity to
VDD and VSS, however briefly.
340B7
Use a clean power source free from transients. Power-up conditions are
occasionally jolting and may
341B85
exceed the maximum ratings of SUR modules. The VDD power of SUR module should
also supply the power to all devices that may access the
342B96
display. Don’t allow the data bus to be driven when the logic supply to the
module is turned off. 43B07
45B32198
6.3 Operating Precautions DO NOT plug or unplug SUR module when the system is
powered up.
345B29
Minimize the cable length between SUR module and host MPU.
346B0
For models with backlights, do not disable the backlight by interrupting the
HV line. Unload inverters
347B1
produce voltage extremes that may arc within a cable or at the display.
Operate SUR module within the limits of the modules temperature
specifications.
348B52
6.4 Mechanical/Environmental Precautions
349B652
Improper soldering is the major cause of module difficulty. Use of flux
cleaner is not recommended
350B47
as they may seep under the electrometric connection and cause display failure.
351B48
Mount SUR module so that it is free from torque and mechanical stress.
352B496
Surface of the LCD panel should not be touched or scratched. The display front
surface is an easily
35B047
scratched, plastic polarizer. Avoid contact and clean only when necessary with
soft, absorbent cotton dampened with petroleum benzene. Always employ anti-
static procedure while handling SUR module.
354B18
Prevent moisture build-up upon the module and observe the environmental
constraints for storage tem
35B249
Do not store in direct sunlight
356B0
If leakage of the liquid crystal material should occur, avoid contact with
this material, particularly ingestion.
357B41
If the body or clothing becomes contaminated by the liquid crystal material,
wash thoroughly with water and soap
468B352
6.5 Storage Precautions When storing the LCD modules, avoid exposure to direct
sunlight or to the light of fluorescent lamps.
359B6
Keep SUR modules in bags (avoid high temperature / high humidity and low
temperatures below 0C
360B574
Whenever possible, SUR LCD modules should be stored in the same conditions in
which they were
361B58
shipped from our company.
458B3629
6.6 Others Liquid crystals solidify under low temperature (below the storage
temperature range) leading to defective
36B057
orientation or the generation of air bubbles (black or white). Air bubbles may
also be generated if the module is subject to a low temperature. If SUR LCD
modules have been operating for a long time showing the same display patterns,
the display
364B158
patterns may remain on the screen as ghost images and a slight contrast
irregularity may also
www.surenoo.com
Page: 17 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
appear. A normal operating status can be regained by suspending use for some
time. It should be noted that this phenomenon does not adversely affect
performance reliability. To minimize the performance degradation of the LCD
modules resulting from destruction caused by static
365B29
electricity etc., exercise care to avoid holding the following sections when
handling the modules. -Exposed area of the printed circuit board.
36B0
-Terminal electrode sections.
69B3845 362B 367B41
7. USING LCD MODULES HH
7.1 Liquid Crystal Display Modules
369B14507
SUR LCD is composed of glass and polarizer. Pay attention to the following
items when handling. Please keep the temperature within specified range for
use and storage. Polarization degradation, bubble
371B685
generation or polarizer peel-off may occur with high temperature and high
humidity. Do not touch, push or rub the exposed polarizers with anything
harder than an HB pencil lead (glass,
372B69
tweezers, etc.). N-hexane is recommended for cleaning the adhesives used to
attach front/rear polarizers and reflectors
37B06
made of organic substances which will be damaged by chemicals such as acetone,
toluene, ethanol and isopropylalcohol. When SUR display surface becomes dusty,
wipe gently with absorbent cotton or other soft material
374B168
like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging
the display surface. Wipe off saliva or water drops immediately, contact with
water over a long period of time may cause
375B269
deformation or color fading.
376B0
Avoid contacting oil and fats.
37B41
Condensation on the surface and contact with terminals due to cold will
damage, stain or dirty the polarizers.
378B52
After products are tested at low temperature they must be warmed up in a
container before coming is contacting with room temperature air. Do not put or
attach anything on SUR display area to avoid leaving marks on.
379B6
Do not touch the display with bare hands. This will stain the display area and
degradate insulation
380B74
between terminals (some cosmetics are determinated to the polarizers).
381B75
As glass is fragile. It tends to become or chipped during handling especially
on the edges. Please
382B796
avoid dropping or jarring.
38B07
7.2 Installing LCD Modules Cover the surface with a transparent protective
plate to protect the polarizer and LC cell.
384B17259
When assembling the LCM into other equipment, the spacer to the bit between
the LCM and the fitting
386B0
plate should have enough height to avoid causing stress to the module surface,
refer to the individual
387B41
specifications for measurements. The measurement tolerance should be±0.1mm.
www.surenoo.com
Page: 18 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
7.3 Precaution for Handling LCD Modules Since SUR LCM has been assembled and
adjusted with a high degree of precision; avoid applying
389B6
excessive shocks to the module or making any alterations or modifications to
it. Do not alter, modify or change the shape of the tab on the metal frame.
390B874
Do not make extra holes on the printed circuit board, modify its shape or
change the positions of
391B85
components to be attached. Do not damage or modify the pattern writing on the
printed circuit board.
392B86
Absolutely do not modify the zebra rubber strip (conductive rubber) or heat
seal connector.
39B087
Except for soldering the interface, do not make any alterations or
modifications with a soldering iron.
394B18
Do not drop, bend or twist SUR LCM.
395B28
7.4 Electro-Static Discharge Control Since this module uses a CMOS LSI, the
same careful attention should be paid to electrostatic discharge as
397B41
for an ordinary CMOS IC. Make certain that you are grounded when handing LCM.
398B52
Before remove LCM from its packing case or incorporating it into a set, be
sure the module and your body
39B6
have the same electric potential. When soldering the terminal of LCM, make
certain the AC power source for the soldering iron does not leak.
40B397
When using an electric screwdriver to attach LCM, the screwdriver should be of
ground potentiality to
401B3985
minimize as much as possible any transmission of electromagnetic waves
produced sparks coming from the commutator of the motor. As far as possible
make the electric potential of your work clothes and that of the work bench
the ground
402B396
potential. To reduce the generation of static electricity be careful that the
air in the work is not too dried. A relative
403B97
humidity of 50%-60% is recommended.
7.5 Precaution for Soldering to SUR LCM Observe the following when soldering
lead wire, connector cable and etc. to the LCM.
46B0158392
-Soldering iron temperature : 280±10
406B3
-Soldering time: 3-4 sec.
407B1
-Solder: eutectic solder.
408B52
If soldering flux is used, be sure to remove any remaining flux after
finishing to soldering operation. (This
409B63
does not apply in the case of a non-halogen type of flux.) It is recommended
that you protect the LCD surface with a cover during soldering to prevent any
damage due to flux spatters. When soldering the electroluminescent panel and
PC board, the panel and board should not be detached
410B7
more than three times. This maximum number is determined by the temperature
and time conditions mentioned above, though there may be some variance
depending on the temperature of the soldering iron. When remove the
electroluminescent panel from the PC board, be sure the solder has completely
melted,
41B085
the soldered pad on the PC board could be damaged.
www.surenoo.com
Page: 19 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
7.6 Precaution for Operation Viewing angle varies with the change of liquid
crystal driving voltage (VO). Adjust VO to show the best
413B07
contrast. Driving the SUR LCD in the voltage above the limit shortens its
life.
41B08
Response time is greatly delayed at temperature below the operating
temperature range. However, this
415B209
does not mean the LCD will be out of the order. It will recover when it
returns to the specified temperature range. If SUR display area is pushed hard
during operation, the display will become abnormal. However, it will
416B30
return to normal if it is turned off and then back on. Condensation on
terminals can cause an electrochemical reaction disrupting the terminal
circuit. Therefore,
417B
it must be used under the relative condition of 40, 50% RH. When turning the
power on, input each signal after the positive/negative voltage becomes
stable.
418B52
7.7 Limited Warranty Unless agreed between SUR and customer, SUR will replace
or repair any of its LCD modules which are
49B163 420B17
found to be functionally defective when inspected in accordance with SUR LCD
acceptance standards (copies available upon request) for a period of one year
from date of shipments. Cosmetic/visual defects must be returned to SUR within
90 days of shipment. Confirmation of such date shall be based on freight
documents. The warranty liability of SUR limited to repair and/or replacement
on the terms set forth above. SUR will not be responsible for any subsequent
or consequential events.
7.8 Return Policy No warranty can be granted if the precautions stated above
have been disregarded. The typical
42B196
examples of violations are: -Broken LCD glass.
423B017
-PCB eyelet damaged or modified.
42B18
-PCB conductors damaged.
425B19
-Circuit modified in any way, including addition of components.
426B30
-PCB tampered with by grinding, engraving or painting varnish.
427B1
-Soldering to or modifying the bezel in any manner.
428B5
Module repairs will be invoiced to the customer upon mutual agreement. Modules
must be returned with
429B63
sufficient description of the failures or defects. Any connectors or cable
installed by the customer must be removed completely without damaging the PCB
eyelet’s, conductors and terminals .
430B27
That’s the end of the datasheet
www.surenoo.com
Page: 20 of 20
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
Serial Test Code
/======================================================================================/
/* ST7032 Test Code
*/
/======================================================================================/
include <reg51.H>
sbit cs1=P3^2; sbit reset=P1^1; sbit rs=P310; sbit sclk=P1^2; sbit sid=P1^3;
sbit key=P2^0; #define uchar unsigned char #define uint unsigned int
/======================================================================================/ char code CGRAM_code[]={ 0x1f,0x1f,0x1f,0x1f,0x1f,0x1f,0x1f,0x1f, 0x1f,0x11,0x11,0x11,0x11,0x11,0x11,0x1f, 0x1f,0x00,0x1f,0x00,0x1f,0x00,0x1f,0x00, 0x00,0x1f,0x00,0x1f,0x00,0x1f,0x00,0x1f, 0x0a,0x0a,0x0a,0x0a,0x0a,0x0a,0x0a,0x0a, 0x15,0x15,0x15,0x15,0x15,0x15,0x15,0x15, 0x0f,0x09,0x0f,0x09,0x0f,0x09,0x11,0x00, 0x08,0x0f,0x12,0x0f,0x0a,0x1f,0x02,0x02, }; char code CGRAM[]= {0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x07};
char code japanese1[]= {0xb0,0xb1,0xb2,0xb3,0xb4,0xb5,};
char code japanese2[]= {0xb6,0xb7,0xb8,0xb9,0xba,0xbb,};
/**/ void delay(int i) {
int j,k; for(j=0;j<i;j++) for(k=0;k<110;k++); }
/**/
void delay_us(int i)
{
int j,k;
for(j=0;j<i;j++)
431B285
for(k=0;k<1;k++);
}
/P2.0 GND /
431B285
void waitkey()
www.surenoo.com
(Test Code) Page: I1 of I4
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
{ repeat: if (P2&0x01) goto repeat; else delay(500); if (P2&0x01) goto repeat;
else; delay(400);
}
/ LCD / void transfer_command(int data1) {
char i; cs1=0; rs=0; for(i=0;i<8;i++) {
sclk=0; if(data1&0x80) sid=1; else sid=0; sclk=1; delay_us(5);
data1=data1<<=1; } cs1=1; }
/ LCD / void transfer_data(int data1) {
char i; cs1=0; rs=1; for(i=0;i<8;i++) {
sclk=0; if(data1&0x80) sid=1; else sid=0; sclk=1; delay_us(5);
data1=data1<<=1; } cs1=1; }
/ LCD MODULE/ void initial_lcd() {
transfer_command(0x38); transfer_command(0x01); delay(5); transfer_command(0x06); delay(5); transfer_command(0x0c); delay(5); transfer_command(0x39); transfer_command(0x1c); delay(5);
/function select/ /clear screen/
/setdisplay mode/ 431B285
/turn on display/
/extension instruc431B285 tion/ //
www.surenoo.com
Model No.:3ASLC1602I (Test Code) Page: I2 of I4
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
transfer_command(0x6d); delay(5); transfer_command(0x55); delay(5); transfer_command(0x7a); delay(5);
// //, 0x54-0x57 //, 0x70-0x7f
}
void write_CGRAM() {
int i;
transfer_command(0x38); /extension instruction/ transfer_command(0x40); //set position
for(i=0;i<64;i++) {
transfer_data(CGRAM_code[i]); }
}
/57 / void disp_char(int line,int column,char code dp) {
int i; transfer_command(0x80+(line-1)*0x40+(column-1)); //set position
for(i=0;i<16;i++) {
transfer_data(*dp); dp++; }
}
/57 */ void disp_CGRAM() {
int i,j;
for(j=0;j<8;j++)
{
transfer_command(0x80); //set position
for(i=0;i<16;i++)
{
transfer_data(CGRAM[j]);
}
transfer_command(0xc0); //set position
for(i=0;i<16;i++)
{
transfer_data(CGRAM[j]);
}
431B285
waitkey();
}
}
www.surenoo.com
Model No.:3ASLC1602I (Test Code) Page: I3 of I4
SHENZHEN SURENOO TECHNOLOGY CO.,LTD.
Model No.:3ASLC1602I
/Main Code/ void main(void) {
reset =0; delay(20); reset =1; delay(100); initial_lcd(); write_CGRAM();
while(1) {
disp_char(1,1,”SLC1602I-888”); /11 / disp_char(2,1,”*Character COG”);
/ 2 1 / waitkey(); disp_char(1,1,japanese1); / 2 1 /
disp_char(2,1,japanese2); / 2 1 / waitkey(); disp_char(1,1,”SURLCD
1602I-888″); /11 / disp_char(2,1,”*2018/01/02 COG*”); / 2 1 / waitkey();
disp_char(1,1,”0123456789 123”); / 1 1 / disp_char(2,1,”Character
COG”); / 2 1 / waitkey(); disp_char(1,1,”xxxxxxxxxxxxxx”); / 1 1 /
disp_char(2,1,”cccccccccccccc”); / 2 1 / waitkey(); disp_CGRAM();
waitkey(); } }
www.surenoo.com
(Test Code) Page: I4 of I4
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>