Lightcloud LCBLUECONTROL-W Controller User Manual

June 3, 2024
Lightcloud

Lightcloud-LCBLUECONTROL-W-Controller-LOGO

Lightcloud LCBLUECONTROL-W Controller

Lightcloud-LCBLUECONTROL-W-Controller-PRODUCT

Hello

The Lightcloud Blue Controller is a remotely controlled device used to enable switching and dimming. The Controller converts any standard 0-10V LED fixture to a Lightcloud Blue-enabled fixture which can be configured and controlled using the Lightcloud Blue mobile app.

Product Features

  • Wireless Control & Configuration
  • Switching up to 3.3A
  • 0-10V Dimming
  • Power Monitoring
  • Patent Pending

Contents

Lightcloud-LCBLUECONTROL-W-Controller-
FIG-1

Specifications & Ratings

  • PART NUMBER LCBLUECONTROL/W
  • Power Consumption
  • <0.6W(Standby)–1W(Active)
  • LOAD SWITCHING CAPACITY
  • LED/Fluorescent Incandescent
  • 120V~1A/120VA 120V~3.3A/400W
  • 277V~1A/250VA 277V~1.5A/400W
  • OPERATING TEMPERATURE
  • Max Temp: -4°F to 113°F (-20°C to 45°C)
  • INPUT
  • 120~277VAC, 50/60Hz
  • DIMENSIONS:
  • 1.3” (D) x 2.5”(L)
  • WIRELESS RANGE
  • 60 ft.
  • RATINGS:
  • IP20 Indoor

Setup & Installation

  1. Turn off power

WARNING

Find a suitable location

  • Lightcloud Blue devices should be positioned within 60 ft. of each other.
  • Building materials such as brick, concrete, and steel construction may require additional Lightcloud Blue devices to extend around an obstruction.

Install the Lightcloud Blue Controller in the junction box
The Lightcloud Blue Controller can be mounted into a junction box, with the radio module always outside any metal enclosure. If no sensor is used, then the second modular cable can be tied off and placed inside the fixture or box .Lightcloud-LCBLUECONTROL-W-Controller-FIG-4

Install luminaire

  • Install the fixture with integrated Lightcloud Blue Controller to a constant power source.
  • Do not place Lightcloud Blue-controlled fixtures down the circuit from any other switching devices such as switches, sensors, or time clocks.

Turn power on

Verify power and local control
Confirm Status Indicator is blinking red. Confirm local control using the Device Identification Button.Lightcloud-LCBLUECONTROL-W-Controller-
FIG-5

Enable Device Pairing Mode
Press and hold for 10s to reset the device to factory settings and into pairing mode.
Commission

  1. Download Lightcloud Blue App from the Apple® App store or Google® Play.
  2. Tap the ‘+ Add Devices’ button in the Lightcloud Blue App to add the Controller while it is in pairing mode.
  3. Use the App to configure settings.

Functionality

Configuration

  • All configuration of Lightcloud Blue products may be performed using the Lightcloud Blue app.

Emergency default

  • If communication is lost, the Controller may optionally fall back to a specific state, such as turning the attached luminaire on.
  • [ Warning: Any wires not in use must be capped off or otherwise insulated. ]
  • WE’RE HERE TO HELP:
  • 1 (844) LIGHTCLOUD 1844-544-4825
  • support@lightcloud.com

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that inter-ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
  • To comply with the FCC’s RF exposure limits for general population / uncontrolled exposure, this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION: Changes or modifications to this equipment not expressly approved by RAB Lighting may void the user’s authority to operate this equipment.

Lightcloud Blue is a Bluetooth mesh wireless lighting control system that allows you to control RAB’s various compatible devices. With RAB’s patent- pending Rapid Provisioning technology, devices can be quickly and easily commissioned for residential and large commercial applications using the Lightcloud Blue mobile app. Each device in a system can communicate with any other device, eliminating the need for a Gateway or Hub and maximizing the control system’s reach. Learn more at www.rablighting.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals