FEIT ELECTRIC FLD30-RGB-LED Multi-Color LED Flood Light with RF Remote Control Installation Guide
- June 3, 2024
- Feit Electric
Table of Contents
FLD30-RGB-LED Multi-Color LED Flood Light with RF Remote Control
Installation Guide
FLD30-RGB-LED Multi-Color LED Flood Light with RF Remote Control
IMPORTANT,
RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Safety Information
READ ALL INSTRUCTIONS
- All safety and operating instructions in this manual must be followed before using this product.
- Follow all safe guards stated in the manual, in addition to normal safety precautions in working with electrical devices. Always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury.
- Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or for the wet location portable luminaire. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety.
- Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW,SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.
- To disconnect, tum off the unit, then remove the plug from the outlet. Do not tum off by pulling on the cord.
- To reduce the risk of fire, Keep away from combustible materials while in operation.
- To reduce the risk of injury, close supervision is necessary when this product is used near children.
- Suitable for Wet Locations.
- Must not be connected to a dimmer.
- Operating Temperature: -4°F to 113°F (-20°C to 45°C).
- This product is not user-serviceable. Do not attempt to open the product enclosure for any reason.
- Unplug from outlet before installing this product.
SAVE THESE INSTRUCTIONS
Maintenance and Care
Regularly clean the lens with a non-abrasive cleaning cloth. The same care
should be provided for the bracket.
FCC Statement
Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance
Information Responsible Party: Feit Electric Company 4901 Gregg Road, Pico
Rivera, CA 90660 Unique Identifier: FLD30/RGB/LED
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Note: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the ealer or an experienced radio/TV technician
for help. Any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Limited Warranty
This product is warranted to be free from defects in workmanship and
materials for up to 1 year from date of purchase. If the product fails within
the warranty period, please contact Feit Electric at info@feit.com
or visit feit.com/contact-us for instructions on
replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces
do not allow the exclusion of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from
state to state or province to province.
WARNING: RISK OF SHOCK. House electric current can cause painful shock or
serious injury unless handled properly.
WARNING: When using outdoor use portable luminaires, basic safety
precautions should always be followed to reduce the risk of fire, electric
shock, and personal injury.
WARNING: Use only three-wire outdoor extension cords that have three-
prong grounding plugs and grounding receptacles that accept the appliance’s
plug. Do not use an extension cord near water or in areas where water may
accumulate. Keep away from pools or spas. Keep plugs dry.
WARNING: Eye damage caused by high light intensity. Never look directly
into the light source.
BATTERY WARNING:
Risk of fire, explosion, and bums. Do not disassemble, crush, heat above
100° C / 212° F or incinerate. REPLACE ONLY WITH one CR2032 battery. DISPOSE
OF USED BATTERY PROMPTLY. KEEP AWAY FROM CHILDREN. DO NOT DISASSEMBLE AND DO
NOT DISPOSE OF IN FIRE. When replacing battery, ensure the new battery is
installed correctly with regard to polarity (+ and -) as shown on remote.
CAUTION:
Dispose of used battery promptly according to local recycling or waste
regulations. Clean battery contacts and also device contacts prior to
installing battery. Ensure the battery is installed correctly with regard to
polarity (+ and —). Remove battery from remote when not being used for an
extended period of time. Remove used battery promptly.
WARNING:
- WARNING – KEEP BATTERIES OUT OF REACH OF CHILDREN
- Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns and potential perforation of the esophagus.
- If you suspect your child has swallowed or inserted a button battery, immediately seek urgent medical assistance.
- Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if compartment is not secure.
- Dispose of used button battery immediately and safely. Flat battery can still be dangerous.
This product contains a button battery. If swallowed, it could cause severe Injury or death In Just 2 hours. Seek medical attention Immediately.
Pre-Installation
HARDWARE INCLUDED
NOTE: Parts not shown to actual size. 
| Part | Description | Quantity |
|---|---|---|
| A | Multi-Color LED Flood Light | 1 |
| B | Remote Control | 1 |
| C | Mounting Stake | 1 |
| D | Mounting Screw | 1 |
| E | L-Shaped Tool | 1 |
Description
Flood Light with Color Memory Function
- 100-240VAC 60Hz, 30W
- 110° Beam Angle
- IP66 Water Resistant
ON/OFF Button Instruction
- ON: Press once to turn the Flood Light on.
- OFF: Press and hold for two seconds to turn the Flood Light off.
- CYCLE: Press when the Flood Light is on to cycle through the colors, fade mode, then off.
Installation
Mounting with Ground Stake
-
Insert Ground Stake
Find the desired location. Plant the mounting stake (C) by firmly pressing it into the soil, use a rubber mallet (not included) if necessary, until the entire stake is in the ground. NOTE: If the soil is hard, dig or wet the ground, to make it easier to plant the stake.
WARNING:
These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with this install guide, current electrical codes and/or the current National Electric Code (NEC). -
Attach LED Flood Light to Mounting Stake
Install LED Flood Light to mounting stake (C) by inserting mounting screw (D) through the middle slot of the mounting stake. Tighten screw with L-shape tool (E). -
Adjust the LED Flood Light Angle
Pivot the Flood Light vertically into your desired position/angle. Once set, tighten the Pivoting Bolt using the L-shape tool (E).
NOTE:
Device can be mounted on the wall, ceiling or floor.
Remote Control Instructions
Set Timer
- Choose a three, six or 12 hour interval using the timer buttons.
- The light will turn on once every day for the selected interval until the timer is canceled or the device is unplugged.
- To cancel the timer, press one of the timer buttons rapidly three times until the Flood Light flashes twice indicating the timer has been canceled.
Create a Custom Color
- Press the MIX1, MIX2, or MIX3 button.
- Create a custom color by mixing red, green, and blue using the up or down arrows.
Mode Description
- Auto: Rotate through different modes.
- Flash: Turns color on and off.
- FadeMix: Smoothly transitions through custom colors.
- Fade7: Smoothly transitions through seven preset colors.
- CycleMix: Rotates through custom colors.
- Cycle7: Rotates through seven preset colors.
Control Multiple Flood Lights with One Remote
Multiple Flood Lights can be controlled together by pairing them to one
remote.
How to Pair to a New Remote
Plug in the Flood Light you would like to pair. Within three seconds, press
and hold the power button on the new remote. The Flood Light will blink three
times and be controlled by that remote. It will no longer be controlled by the
original remote.
How to Unpair
To make it so no remote controls the Flood Light, plug in your Flood Light.
Within three seconds press and hold the power button on the remote it is
currently paired with. The Flood Light will flash six times to show it is
unpaired. The Flood Light can be controlled by the ON/OFF button on the unit
or later paired with another remote.
NOTE: Obstructions can reduce the range of the remote. Test the remote
performance before installation.
**** Thank you for your purchase. Questions, comments
or feedback? We’d love to hear from you.
Visitfeit.com/helpforsupport.
FEIT ELECTRIC COMPANY
PICO RIVERA, CA. USA
www.feit.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>