Surenoo STP0177D-128160 Series TFT LCD Panel User Manual

June 3, 2024
Surenoo

Surenoo STP0177D-128160 Series TFT LCD Panel

General Description

MODEL NO

| STP0177D-128160
---|---
Display Mode

| Transmissive
Display Format

| Graphic 128RGB*160 Dot-matrix
Input Data

| 8080-8
Viewing Direction

| 12 o’clock
Drive

| ST7735S

Mechanical Specification

Item Specifications Unit

Dimensional outline

| 34.00(W)45.83(H)2.40MAX(T)| mm
Resolution

| 128RGB*160| dots
LCD Active area

| 28.03 (W)*35.04 (H)| mm
Pixel size

| 0.219(W)*0.219(H)| mm

Mechanical Dimension

Surenoo STP0177D-128160 Series TFT LCD Panel-fig3

Electrical Maximum Ratings

Item

| Symbol

| Min

| Max

| Unit

| Note

---|---|---|---|---|---
Supply voltage VDDI

| ****

V

| ****

1.8

| ****

3.3

| ****

V

| ****

Supply voltage VDD

| ****

V

| ****

2.8

| ****

3.3

| ****

V

| ****

Operating temperature | ****

T OPR

| ****

20

| ****

70

| | ****

Storage temperature

| ****

T STR

| ****

30

| ****

80

| | ****

Brightness characteristic&Power dissipation

Item

| Symbol

| Min

| Typical

| Max

| ****

Unit

---|---|---|---|---|---
LED module Forward voltage

| ****

V LED

| 2 9| ****

3.1

| ****

3.3

| ****

V

LED module current

| ****

I LED

| ****

| ****

18

| ****

| ****

mA

LCD Surface Luminance

| ****

L S

| ****

180

| ****

200

| ****

| C d / m 2
LCD Surface brightness uniform

| ****

L D

| ****

80

| ****

| ****

| %
LCD power dissipation

| ****

P LCD

| ****

| ****

0.11

| ****

| W

Module Function Description

Display Pin


PIN No.

| ****

Symbol

| ****

Description

| ****

Notes

---|---|---|---
1| LED-K| Cathode of Backlight

| ****

2| LED-A| Anode of Backlight (2.9V-3.3V Typical:3.1V)

| ****

3| GND| Ground

| ****

4| VDD| Power Supply for LCD.

| ****

5-6| NC| No connection

| ****


7

| ****

CSX

| -Chip selection pin Low enable.

High disable.

| ****


8

| ****

RESX

| -This signal will reset the device and it must be applied to properly initialize the chip.

-Signal is active low.

| ****



9

| ****


DCX

| -Display data/command Selection Pin in MCU Interface.

DCX=’1’: display data or parameter.) DCX=’0’: command data

| ****



10| WRX| -Write enable in MCU parallel interface.

| ****


11

| ****

RDX

| -Read enable in 8080 MCU parallel interface.

-If not used, please fix this pin at VDDI or GND.

| ****

12-19| DB7-DB0| MCU parallel interface data bus.

| ****

20| GND| Ground

| ****

STP0177D-128160

Surenoo STP0177D-128160 Series TFT LCD Panel-fig4

Response time&Contrast ratio

Item


| Symbol


| Condition


| Remark| Unit


---|---|---|---|---
Min.


| Typ.


| Max.


Response time

| Tr+Tf| θ=0°| –| 30| 60| ms
Contrast ratio

| CR| θ=0°| 200| 300| –|

Surenoo STP0177D-128160 Series TFT LCD Panel-fig5

Surenoo STP0177D-128160 Series TFT LCD Panel-fig14

Viewing Angle

Item


| Symbol


| Condition


| Remark| Unit


---|---|---|---|---
Min.


| Typ.


| Max.




Viewing angle

| Top

| CR≥10

| 40| 50| –| ****


Deg.

Bottom

| CR≥10

| 50| 60| –
Left

| CR≥10

| 50| 60| –
Right

| CR≥10

| 50| 60| –

Surenoo STP0177D-128160 Series TFT LCD Panel-fig6

Reliability Trial

NO.


| ITEM


| CONDITION


| CRITERION


---|---|---|---
1| High Temperature Non-Operating Test| 80℃120Hrs| No Defect Of
 | Operational
2| Low Temperature Non-Operating Test| -30℃
120Hrs| Function In Room
 | Temperature Are
3| High Temperature/Humidity Non Operating Test| 60℃90%RH120Hrs| Allowable
 |
4| High Temperature Operating Test| 70℃72Hrs|
 |
5| Low Temperature Operating Test| -20℃
72Hrs|
 |
6| Thermal Shock Test| -20 ℃ (30Min) n 70 ℃|
 | (30Min) *10CYCLES|

Inspection standards

Glass defect

NO Defect item Criteria Remark

1

| Dimension Unconformity

(Major defect)

| By Engineering Drawing|



2

| Cracks

(Major defect)

| 1.        Linear cracks panel

【Reject】

2.        Nonlinear crack contrast by limited sample

| ****




3

| Glass extrude the conductive area

(minor defect)

| a: disregards and no influence assemblage.

1)       b≤1/3Pin width(non bonding area)

【Accept】

  1. bonding area≤0.5mm

【Accept】

| A: Length, b: Width



4

| Pin-side ,conductive area damaged

(minor defect)

| (a c: disregards)

b≤1/3of effective length for bonding electrode

【Accept】

| a: length, b: Width, c: Thickness


5| Pin-side,non-conductive

area damaged

| 1)Damage area don’t touch the ITO

(Inclueling contraposition mark,

| a: Length, b: Width c:

Thickness

 | (minor defect)| except scribing mark)

【Accept】

2)  C<T b≦BM1/3of width

【Accept】

3)  c=T

b not touch the seal glue

【Accept】

4)  a disregards

| ****
---|---|---|---





6

| Non-pin-side damage

(minor defect)

| c<T

1)b exceeds 1/3Bm

【Reject】

c=T

b not touch the seal glue

【Reject】

| c: Thickness b: width of

damage

LCD appearance defect(View area)

NO Defect item Criteria Remark




1

| ****


Fiber、glass cratch、polarizer scratch/folded

(minor defect)

| Specification| Allowable| note1:L: Length, W: Width note2: disregard if out of AA


W≦0.03mm| disregard
0.03mm<W≦0.05mm;

L≦3.0mm

| 2
0.05mm<W≦0.1mm;

L≦3.0mm

| 1
W>0.1mm;L>3.0mm| 0



2

| Polarizer bubble、 concave and convex

(minor defect)

| φ≦0.2mm| disregard| note1: φ=(L+W)/2,L:Length,

W :Width

note2:disregard if out of AA

0.2mm<φ≦0.3mm| 2
0.3mm<φ≦0.5mm| 1
0.5mm<φ| 0



3

| ****

Black dots、dirty dots、 impurities、eye winker

(minor defect)

| φ≦0.15mm| disregard| note2:disregard if out of AA


0.15mm <φ≦0.25mm| 2
0.25mm<φ≦0.3mm| 1
0.3mm<φ| 0



4

| ****

Polarizer prick

(minor defect)

| φ≦0.1mm| disregard| note1: φ=(L+W)/2,L=Length,

W=Width

note2:the distance between two dots>5mm

0.1mm<φ≦0.25mm| 3
φ>0.25mm| 0

Package Method

Surenoo STP0177D-128160 Series TFT LCD Panel-fig13

Surenoo STP0177D-128160 Series TFT LCD Panel-fig2

Shenzhen Surenoo Technology Co.,Ltd. www.surenoo.com
Skype: Surenoo365

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals